• 한국전기전자재료학회논문지
• /
• 제11권11호
• /
• pp.1028-1034
• /
• 1998

Bi-2223 superconductor is known as one of the candidates for practical superconducting wires. Ag-sheathed Bi-2223 superconducting wires were fabricated using the powder-in-tube(PIT) method. When the 19-filaments wire was immersed in liquid nitrogen(77K), maximum critical current density Jc of 62 A/$mm_2$ at 0T was achieved. The critical current density has been shown to depend on the mechanical properties such as tensile stress and bending strain in Ag-sheathed Bi-2223 superconducting wires. The tensile strain for Jc degradation onset was in the range of 0.12~0.3%. In the case of 19-filaments wire, the bending strain is estimated to be smaller than 0.3% for the reasonable Jc value. The observed degradation of the critical current density due to strain effect is inevitable and can be attributed to the formation of microcracks within the superconducting core.

• 콘크리트학회논문집
• /
• 제16권6호
• /
• pp.767-776
• /
• 2004

폴리머콘크리트는 시멘트 콘크리트에 비해 강도와 내구성에 탁월한 성능을 가지고 있기 때문에 건설현장에서도 다양한 용도로 개발되어 널리 사용되고 있다. 그러나 폴리머콘크리트는 그 결합재로 쓰이는 수지의 비용이 높아 경제적인 면에서는 다소 불리하여 기존의 수지를 대체할 수 있는 결합재에 관한 연구가 진행되고 있다. PET를 재활용한 폴리머콘크리트는 산업폐기물을 재활용하여 경제적인 건설 신소재를 개발할 수 있어 그 영역이 점차 확대 될 것으로 전망된다. 본 연구에서는 프리캐스트 제품 및 구조부재로의 응용과 자원 재활용을 목적으로 PET 재생 불포화 폴리에스터수지를 이용하여 고강도의 폴리머콘크리트를 제조하고 이에 대한 응력-변형률 거동 특성을 파악하여 실험결과와 이론적 근거를 바탕으로 PET 재활용 폴리머콘크리트의 응력-변형률 곡선의 모델식을 얻고자 하였다. 실험 결과 수지 사용량의 증가에 따라 최대 응력과 최대 변형률이 함께 증가하였으나 증가폭에 한계가 있는 것으로 나타났으며 응력-변형률 곡선의 기울기는 상온보다는 고온양생이 더 크게 나타났다. 실란의 첨가는 강도증진의 효과뿐만 아니라 최대하중 이후의 압축 연화거동에 효과적인 것으로 나타났다. 또한 위와 같은 응력-변형률 거동 특성을 통하여 PET 재활용 폴리머콘크리트 응력-변형률 곡선의 수정 모델식을 제안하였으며 PET 재활용 폴리머콘크리트의 특성을 정확히 예측하였다.

• 한국지반공학회논문집
• /
• 제16권4호
• /
• pp.95-105
• /
• 2000

공중낙하법에 의해 만든 등방압밀 모래공시체를 미소변형률 측정장치를 사용한 평면변형률압축시험을 실시하여 미소변형률에서 파괴후까지의 전단강성계수에 대한 이방성을 연구하였다. 세계각국의 주요 연구기관에서 사용되고 있는 7종류의 연구용 표준사 공시체를 멤브레인의 관입에 의한 오차와 변위를 외부에서 측정함으로 하여 생기는 오차(bedding error)등의 영향을 제거하여 측정한 최대주응력방향의 변형률과 최소주응력방향의 변형률을 각각 0.0001%에서 10%까지 넓은 범위에 걸친 응력-변형률 관계를 얻었다. 그 결과 최대전단강성계수 Gmax는 퇴적면과 최대주응력 $\sigma$1이 이루는 각도 $\delta$에 관계없이 일정하였다. 그러나 정규화한 Gmax는 모래의 종류에 따라 달랐다. 또 전단강성계수의 변형률 수준과 응력 수준에 대한 의존성은 $\delta$가 감소함에 따라 증가하였다.

• Journal of Mechanical Science and Technology
• /
• 제14권2호
• /
• pp.152-158
• /
• 2000

The contents of this paper include the evaluation of corrosion characteristics and the behaviour of stress corrosion cracking (SCC) for the weldment and post weld heat treatment (PWHT) specimen and parent of HT -60 steel using a slow strain rate test (SSRT) in synthetic seawater. Corrosion characteristics were obtained from the polarization curves by potentiostat, and SCC phenomena were evaluated through the parameters such as reduction of area and time to failure by comparing the experimental results in corrosive environment with those obtained in air. Corrosion rate of the weldment was the fastest, followed by parent and PWHT specimen. SCC phenomena between the weldment of HT-60 steel and synthetic seawater were shown. Besides, SCC was dependent upon the pulling speed greatly. Maximum severity of SCC was obtained at a speed of $10^{-6}mm/min$, whereas SCC could not be seen almost at $10^{-4}mm/min$. The resistance to SCC for PWHT specimen was improved considerably compared that of the weldment at $10^{-6}mm/min$. In case of SCC failure, it was verified from SEM examination that brittle mode and lots of pits could be seen at the fractured region near the surface of the specimen.

• 국제초고층학회논문집
• /
• 제9권4호
• /
• pp.325-334
• /
• 2020

This paper aims to evaluate the interfacial stress concentrations on connection between vertical through-plate and H-beam in CFT column. Full-scale experiments were performed on three specimens with varying thickness of the vertical through-plate to investigate the interfacial stress concentration factor in the connections. The specimens underwent brittle failure at the location where the steel beam is connected to the vertical through-plate before the steel beam reached its plastic moment. The strain data of the part were analyzed, and the sectional analyses were conducted to determine appropriate residual stress models. In addition, the stress concentration factor was quantified by comparing the analytical local behavior in which the stress concentration is not reflected and the experimental data reflecting the stress concentration. The results showed that the maximum reduction of the stress concentration factor due to an increase in the thickness of the vertical through-plate is 50.3%.

• 콘크리트학회논문집
• /
• 제13권3호
• /
• pp.195-205
• /
• 2001

본 연구는 화재에 노출된 철근콘크리트 부재의 휭 강도를 평가하기 위한 해석적 연구로서, 고온을 받는 단면에 대한 모멘트-곡률 관계를 구하는 것이다. 해석적 방법으로는 부재 단면에 대한 열전도 해석을 수행한 후 여러 가지 가열 조건에 대한 콘크리트와 철근의 응력-변형률 관계를 이용하여 모멘트-곡률 관계의 해석을 수행한다. 본 연구의 해석 결과는 다음과 같다. (1) 고온에 대한 철근콘크리트 부재의 잔존 휭 강도는 가열시간, 콘크리트 피복두께, 인장철근비의 영향을 받는다. (2) 고온을 받은 후의 잔존 휭 강도는 최소 철근비일 때는 상온시의 강도를 회복하지만, 최대 철근비의 50%일 때와 최대 철근비 일 때는 회복하지 않는 경향을 나타낸다. (3) 최대 철근비를 가진 철근콘크리트 부재는 가열 후 냉각상태에 대하여 철근이 항복하기 전에 콘크리트가 한계상태에 도달하는 경향을 나타낸다.

• 대한토목학회논문집
• /
• 제42권4호
• /
• pp.501-508
• /
• 2022

지하수위 회복을 위한 함양정 운영시 필요 기술은 지반이 파괴에 도달하지 않는 최대 주입압을 결정하는 것이다. 고전적인 토질역학에 기초한 수치해석과 실내시험을 통하여 사질토와 점성토의 항복에 도달하는 최대 주입압력을 추론하였다. 수치해석에서는 주입압력에 따른 점성토의 구속압력 감소에 따른 파괴시, 사질토는 유출동수 경사에 따른 파이핑 발생시 주입압력을 최대 한계압으로 결정하였다. 실내시험에서는 간극수압이 높아지는 것을 배압 증가를 통하여 구현하였으며, 사질토 경우 유효응력이 0이 되기전 최대 배압의 93 %에서 급격한 체적변형이 발생하였다. 점성토의 경우는 유효응력이 0에 도달할 경우 방사방향 변형율이 1.5 %에 도달하였으나 급격한 체적변형이 발생하지 않았다. 따라서 상기 결과에 근거하여 함양정의 최대 주입압력을 수치해석과 실내시험으로 결정할 수 있었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.97-97
• /
• 2009

The use of thin plate increases due to the need for light weight in large ship. Thin plate is easily distorted and has residual stress by welding heat. Therefore, the thin plate should be carefully joined to minimize the welding deformation which costs time and money for repair. For one effort to reduce welding deformation, it is very useful to predict welding deformation before welding execution. There are two methods to analyze welding deformation. One is simple linear analysis. The other is nonlinear analysis. The simple linear analysis is elastic analysis using the equivalent load method or inherent strain method from welding experiments. The nonlinear analysis is thermo-elastic analysis which gives consideration to the nonlinearity of material dependent on temperature and time, welding current, voltage, speed, sequence and constraint. In this study, the welding deformation is analyzed by using thermo-elastic method for PCTC(Pure Car and Truck Carrier) which carries cars and trucks. PCTC uses thin plates of 6mm thickness which is susceptible to welding heat. The analysis dimension is 19,200mm(length) * 13,825mm(width) * 376mm(height). MARC and MENTAT are used as pre and post processor and solver. The boundary conditions are based on the real situation in shipyard. The simulations contain convection and gravity. The material of the thin block is mild steel with $235N/mm^2$ yield strength. Its nonlinearity of conductivity, specific heat, Young's modulus and yield strength is applied in simulations. Welding is done in two pass. First pass lasts 2,100 second, then it rests for 900 second, then second pass lasts 2,100 second and then it rests for 20,000 second. The displacement at 0 sec is caused by its own weight. It is maximum 19mm at the free side. The welding line expands, shrinks during welding and finally experiences shrinkage. It results in angular distortion of thin block. Final maximum displacement, 17mm occurs around welding line. The maximum residual stress happens at the welding line, where the stress is above the yield strength. Also, the maximum equivalent plastic strain occurs at the welding line. The plastic strain of first pass is more than that of second pass. The flatness of plate in longitudinal direction is calculated in parallel with the direction of girder and compared with deformation standard of ${\pm}15mm$. Calculated value is within the standard range. The flatness of plate in transverse direction is calculated in perpendicular to the direction of girder and compared with deformation standard of ${\pm}6mm$. It satisfies the standard. Buckle of plate is calculated between each longitudinal and compared with the deformation standard. All buckle value is within the standard range of ${\pm}6mm$.

• 대한치과보철학회지
• /
• 제38권3호
• /
• pp.348-357
• /
• 2000

The purpose of this study is to examine the effect of partial osseointegration situation on bone loading patterns around two different free-standing screw shaped implants (Nobel Biocare, Gothenburg, Sweden and Degussa-Huls, Hanau, German). Two dimensional axisymmetric Finite element models of two implants(10mm length and 4mm diameter) were created according to different bone quantity, quality and osseointegration ratio in maxilla and mandible bone. At the same time uni-cortical and hi-cortical fixation were analyzed. Generally, full bond case showed less stress than partial bond case in overall area and mandibular model showed less amount of stress than that of maxilla model. Maximum stress of the Branemark implant is higher than that of ANKYLOS regardless of bonding ratio at crestal and apex region. However, more stress concentration was noted in ANKYLOS implant at screw body area especially in mandible. The effect of bicortical fixation on crestal bone stress reduction is dramatical in mandible however, there was no significant effect in maxillary case. The effect of partial bond on stress distribution was more significant at screw body and apex region than in crestal region. Partial bond cases demonstrated greater stress accumulation in trabecular bone than cortical bone. It is concluded that the more accurate model of implant and bone which affects stress and strain distribution is needed to mimic in vivo behavior of implants.

• The Journal of Advanced Prosthodontics
• /
• 제11권3호
• /
• pp.169-178
• /
• 2019

PURPOSE. While dental implants have displayed high success rates, poor mechanical fixation is a common complication, and their biomechanical response to occlusal loading remains poorly understood. This study aimed to develop and validate a computational model of a natural first premolar and a dental implant with matching crown morphology, and quantify their mechanical response to loading at the occlusal surface. MATERIALS AND METHODS. A finite-element model of the stomatognathic system comprising the mandible, first premolar and periodontal ligament (PDL) was developed based on a natural human tooth, and a model of a dental implant of identical occlusal geometry was also created. Occlusal loading was simulated using point forces applied at seven landmarks on each crown. Model predictions were validated using strain gauge measurements acquired during loading of matched physical models of the tooth and implant assemblies. RESULTS. For the natural tooth, the maximum vonMises stress (6.4 MPa) and maximal principal strains at the mandible ($1.8m{\varepsilon}$, $-1.7m{\varepsilon}$) were lower than those observed at the prosthetic tooth (12.5 MPa, $3.2m{\varepsilon}$, and $-4.4m{\varepsilon}$, respectively). As occlusal load was applied more bucally relative to the tooth central axis, stress and strain magnitudes increased. CONCLUSION. Occlusal loading of the natural tooth results in lower stress-strain magnitudes in the underlying alveolar bone than those associated with a dental implant of matched occlusal anatomy. The PDL may function to mitigate axial and bending stress intensities resulting from off-centered occlusal loads. The findings may be useful in dental implant design, restoration material selection, and surgical planning.