• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.158-164
• /
• 2004

In the present work, the numerical model was refined to predict the thermal analysis of energy storage in a fixed beds during charging mode. The governing energy equations of both fluid and the solid particles along with their initial and boundary conditions are derived using a two-phase, one dimensional model. The refined model is carried out by taking into account change of (air density , air specific heat) with air temperature and also by taking into considerations heat losses from bed to surrounding. Finite difference method was used to obtain solution of two governing energy equations of both fluid and solid particles through a computer program especially constructed for this purpose. The temperature field for the air and the solid are obtained, also energy stored inside the bed is computed. A comparison between refined model and non refined model is done. Finally using refined model the effect of bed material (Glass, Fine clay ,and aluminum ), and air flow rate per unit area Ga (0.3, 0.4, and 0.5 kg/$m^2$-s) on energy storage characteristics was studied.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.6
• /
• pp.789-797
• /
• 2006

This study was conducted to establish the refined model for prediction of flocculation/sedimentation efficiency in factual drinking water treatment plants using model tree technique. In order to carry out machine leaning for determining each linear model, five parameters; time, coagulant dose, raw water turbidity, SCD and conductivity, which were measured and collected from the field (K_DWTP), were selected and used. The existing analytical models developed by previous researchers were used only to examine closely the mechanism of flocculation rather than to apply it for practical purpose. The refined model established using model tree technique in this study could predict the factual sedimentation efficiency accurately (below 9% of average absolute error). Also, in aspect of engineering convenience, without any additional manipulation of parameters, it can be applied to practical works.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.4
• /
• pp.225-236
• /
• 2005

The primary goal of the study is to provide a newly refined data model, an information exchange foundation of modeling operation for rapid prototyping, as one among non-milling STEP-NC modules. The previous data model has been first modified and refined by reflecting specific user requirements. Second, subsidiary information such as fabrication history as well as traditional process information has been introduced into the newly refined model in order to consolidate the model functionality. In short, the main contribution of the study is to provide a foundation where a newly refined data model is utilized easily and conveniently for practical rapid prototyping fabrication within the newly constructed STEP-NC environment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.1-10
• /
• 2001

As computer power is increased, refined finite element models are employed for structural analysis. However, it is difficult and expensive to use refined models in the design stage. The refined models especially cause problems in the preliminary design where the design is frequently changed. Therefore, simplified models are needed. The simplification process is regarded as an empirical technique. Simplified and equivalent finite element model of a structure has been studied and used in the preliminary design. A general approach to establish the simplified and equivalent model is presented. The generated simple model has satisfactory correlation with the corresponding refined finite element model. An optimization method, the Goal Programming algorithm is used to make the simple model. The simplified model is used for the design change and the changed design is recovered onto the original design. The presented method was verified with three examples.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.8
• /
• pp.2030-2038
• /
• 1995

In this study, three turbulent flame propagation models are compared using experimentally measured data of a 4 valves/cylinder spark-ignition engine. First two conventional models are B.K model and GESIM combustion model. The burning rates calculated from the two models are compared with the burning rates calculated from measured pressure data using the one-zone heat release analysis. GESIM combustion model predicts burning rates closer to the data acquired from the experiment in wide operating ranges than B-K model does. The third model is refined based on GESIM combustion model by including the effect of flame stretch, turbulent length scale band pass filter and a variable that considers flame size and the area of flame contacting the cylinder wall surface. The refined combustion model predicts burning rates closer to experimental results than GESIM combustion model does. Also, the refined combustion model predicts flame radius close to the experimental result measured by using optical fiber technique.

• Structural Engineering and Mechanics
• /
• v.84 no.3
• /
• pp.423-435
• /
• 2022

In this article, we present torsion-bending analysis of a composite FGM beam with an open section, according to the advanced and refined theory of 1D / 3D beams based on the 3D Saint-Venant's solution and taking into account the edge effects. The (initially one-dimensional) model contains a set of three-dimensional (3D) displacement modes of the cross section, reflecting its 3D mechanical behaviour. The modes are taken into account depending on the mechanical characteristics and the geometrical form of the cross-section of the composite FGM beam. The model considered is implemented on the CSB (Cross-Section and Beam Analysis) software package. It is based on the RBT/SV theory (Refined Beam Theory on Saint-Venant principle) of FGM beams. The mechanical and physical characteristics of the FGM beam continuously vary, depending on a power-law distribution, across the thickness of the beam. We compare the numerical results obtained by the three-beam theories, namely: The Classical Beam Theory of Saint-Venant (Classical Beam Theory CBT), the theory of refined beams (Refined Beam Theory RBT), and the theory of refined beams, using the higher (high) modes of distortion of the cross-section (Refined Beam Theory using distorted modes RBTd). The results obtained confirm a clear difference between those obtained by the three models at the level of the supports. Further from the support, the results of RBT and RBTd are of the same order, whereas those of CBT remains far from those of higher-order theories. The 3D stresses, strains and displacements, obtained by the present study, reflect the 3D behaviour of FGM beams well, despite the initially 1D nature of the problem. A validation example also shows a very good agreement of the proposed models with other models (classical or higher-order beam theory) and Carrera Unified Formulation 1D-beam model with Lagrange Expansion functions (CUF-LE).

• Steel and Composite Structures
• /
• v.18 no.6
• /
• pp.1353-1368
• /
• 2015

A finite element model is presented for the analysis of composite steel-concrete beams based on a refined high-order theory. The employed theory satisfies all the kinematic and stress continuity conditions at the layer interfaces and considers effects of the transverse normal stress and transverse flexibility. The global displacement components, described by polynomial or combinations of polynomial and exponential expressions, are superposed on local ones chosen based on the layerwise or discrete-layer concepts. The present finite model does not need the incorporating any shear correction factor. Moreover, in the present $C^1$-continuous finite element model, the number of unknowns is independent of the number of layers. The proposed finite element model is validated by comparing the present results with those obtained from the three-dimensional (3D) finite element analysis. In addition to correctly predicting the distribution of all stress components of the composite steel-concrete beams, the proposed finite element model is computationally economic.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.17-23
• /
• 2004

In the present work, the numerical model was refined to predict the thermal analysis of energy storage in a fixed beds during (charging ,storing, discharging) mode. The governing energy equations of both fluid and the solid particles along with their initial and boundary conditions are derived using a two-phase, one dimensional model. The refined model is carried out by taking into account change of (air density , air specific heat) with air temperature and also by taking into considerations heat losses from bed to surrounding. Finite difference method was used to obtain solution of two governing energy equations of both fluid and solid particles through a computer program especially constructed for this purpose. The temperature field for the air and the solid are obtained, also efficiency of energy stored inside the bed is computed. Finally using refined model the effect of air flow rate per unit area Ga (0.2, 0.3, and 0.4 kg/$m^2$-s), and inlet air temperature (200, 250, 300 $^{\circ}C$) on energy storage characteristics was studied in three mode ( charging ,storing, discharging). The rock particles of diameter 1 em is used as bed material in this research.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.1
• /
• pp.77-84
• /
• 2022

The experimental work has been carried out for the study of pyrolysis of oil samples used in industrial and utility boilers in Korea. For five oil samples, the characteristics of pyrolysis have been investigated with a thermogravimetric analyzer (TGA), and their kinetic parameters were obtained and compared each other. The rate order of pyrolysis rate for five oils were as follows: by-product fuel oil, pyrolysis oil, diesel, a heavy oil and refined oil. The pyrolysis of refined oil has been successfully described by the three step, first order reaction model while the single step reaction model has been used for other oils. For the reaction temperature over 550 K, the reactivity of refined oil was very poor compared with other oils.

• Wind and Structures
• /
• v.20 no.1
• /
• pp.59-74
• /
• 2015

A coupled model system for Wind Resource Assessment (WRA) was studied. Using a mesoscale meteorological model, the Weather Research and Forecasting (WRF) model, global-scale data were downscaled to the inner nested grid scale (typically a few kilometers), and then through the coupling Computational Fluid Dynamics (CFD) mode, FLUENT. High-resolution results (50 m in the horizontal direction; 10 m in the vertical direction below 150 m) of the wind speed distribution data and ultimately refined wind farm information, were obtained. The refined WRF/FLUENT system was then applied to assess the wind resource over complex terrain in the northern Poyang Lake region. The results showed that the approach is viable for the assessment of wind energy.