• Proceedings of the IEEK Conference
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.437-440
• /
• 1998

We studied phosphorus doping effect on the epitaxial growth of $Si_{1-x}Ge_{x}$ film with high Ge fraction on Si substates at 550.deg. C by LPCVD. In a low $Ph_{3}$ partial pressure region such as below 1.25 mPa, the phosphorus dopant concentration increased linearly with increasing $PH_{3}$ partial pressure while the deposition rate and the Ge fraction were constant. In a higher $PH_{3}$ partial pressure region, the phosphorus dopant concentration and the deposition rate decreased, while the Ge fraction slightly increased. The deposition arate and the Ge fraction increased with increasing $GeH_{4}$ partial pressure while the phophours dopant concentration decreased. But the increasing rate of Ge fraction with incrasing $PH_{3}$ partial pressure was reduced at a high $GeH_{4}$ partial pressure. According to test results, it suggests that high surface coverage of phosphorus atoms suppress both the $SiH_{4}$ adsorption/reasction and the $GeH_{4}$ adsorption/reaction on the surfaces, and the effect is more stronger on $SiH_{4}$ than on $GeH_{4}$. In a higher $PH_{3}$ partial pressure region, the epitaxial growth is largely controlled by surface coverage effect of phosphorus atoms. The phosphorus surface coverage was slimited at a high $GeH_{4}$ partial pressure because adsorbed Ge atoms effectively suppresses the adsorption of phosphorus atoms.

• Journal of Bio-Environment Control
• /
• 제32권4호
• /
• pp.513-520
• /
• 2023

Korean melon (Cucumis melo L.) is an environment in which most farming work can affect the increase in musculoskeletal diseases, and the stems are attracted to the ground in order to grow no-heating cultivation. In this study, growth and productivity were compared according to the type of high-bed. The narrower the surface area at the bottom of the high-bed, the faster the initial growth, which was advantageous. The bed is which the height if 70 cm, the surface temperature has risen due to the increase in direct solar radiation inflow since April, requiring side light blocking to block the inflow of solar radiation. In terms of fruit quality, the 200 cm width treatment had higher fruit sugar content and better hardness than the 160 cm treatment. From April to September, the total yield was 6.8 kg/plant of treatment A, 8.7 kg/plant of treatment B, 5.8 kg/plant of treatment C, treatment B mainly 50% higher than treatment C, and 27% higher than treatment A. Therefore, the bed form suitable for Korean melon high bed is 200 cm wide, 40 cm high between the surface and the bed, and the surface of the passage between the beds is 30cm high from the ground to the bed.

• Journal of the Korean Society for Heat Treatment
• /
• 제29권3호
• /
• pp.124-131
• /
• 2016

GaN and InN epilayers with nucleation layer (LT-buffer) were grown on (0001) sapphire substrates by radio-frequency plasma-assisted molecular beam epitaxy (RF-MBE). As-grown and annealed GaN and InN nucleation layers grown at various growth condition were observed by reflection high-energy electron diffraction (RHEED). When temperature of effusion cell for III source was very low, diffraction pattern with cubic symmetry was observed and zincblende nucleation layer was flattened easily by annealing. As cell temperature increased, LT-GaN and LT-InN showed typical diffraction pattern from wurtzite structure, and FWHM of (10-12) plane decreased remarkably which means much improved crystalline quality. Diffraction pattern was changed to be from streaky to spotty when plasma power was raised from 160 to 220 W because higher plasma power makes more nitrogen adatoms on the surface and suppressed surface mobility of III species. Therefore, though wurtzite nucleation layer was a little hard to be flattened compared to zincblende, higher cell temperature led to easier movement of III surface adatoms and resulted in better crystalline quality of GaN and InN epilayers.

• Journal of the Korean Society of Visualization
• /
• 제22권1호
• /
• pp.61-67
• /
• 2024

In this study, the behavior of water droplets on a solid-infused surface was evaluated by quantifying a water droplet's contact angle, sliding angle, and terminal velocity. The contact angle hysteresis and sliding angle of water on the solid-infused surface were measured to be lower than those of the hydrophobic PTFE surface. It led to the enhancement of the initiation of the water droplet's movement. When the capillary number was lower than Ca < 0.004, the terminal velocity of the water droplet on the solid-infused surface was higher than the PTFE surface due to the low contact line resistance. However, the transition of the droplet morphology from a hemispherical shape to a streamlined teardrop shape beyond Ca > 0.004 lost the effect of reducing frictional resistance on the solid-infused surface.

• Architectural research
• /
• 제10권1호
• /
• pp.33-39
• /
• 2008

Condensation has mainly occurred in corridor type apartment door which is exposed to the outside air and is made of steel, which has high thermal conductivity. As a result, the total costs of repair have increased with the number of disputes with residents. In this study, therefore, we investigate materials and construction methods used in apartment door, perform a computer simulation to find out possible improvements, and then suggest the dew point to prevent the occurrence of condensation throughout simulation. The results indicate that the temperature that condensation does not occur is $15.4^{\circ}C$, and the optimum method of achieving this dew point is shown to be a door frame system including a large vertical slot to decrease the area of thermal conduction between the outer and inner portions of the door frame. Mock-up tests show that the surface temperature of the door frame was higher than the dew point, and the system can withstand severe cold conditions of $-20^{\circ}C$. In application test, the surface temperature of door frame with vertical slots is $5.9^{\circ}C$in average, which is higher than the existing door frame. Furthermore, in the temperature distribution of the surrounding door measured with infrared ray camera, the existing door shows the high temperature distribution indicating lack of insulation, but the improved door shows the low temperature distribution indicating higher insulation.

• Nuclear Engineering and Technology
• /
• 제53권6호
• /
• pp.1939-1941
• /
• 2021

The sputtering yield of tungsten pellets composed of different particle sizes of <1, 12, 44-74, and 149-297 ㎛ was systematically investigated by bombardment with Ar⁺ ions accelerated at 2.0 keV in an ultra-high vacuum chamber. We found that the tungsten sample fabricated from larger particles had a higher surface roughness, based on the surface profile results. Using the data of the surface roughness for the four types of tungsten pellets, we confirmed that the sputtering yield for a tungsten pellet with the highest surface roughness was 7 times lower than that of the lowest surface roughness. This could be due to the redeposition of sputtered tungsten particles onto neighboring asperities.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.81-85
• /
• 2023

This study presents an experimental investigation of the effects of surface roughness on gas foil thrust bearing (GFTB) performance. A high-speed motor with the maximum speed of 80 krpm rotates a thrust runner and a pneumatic cylinder applies static loads to the test GFTB. When the motor speed increases and reaches a specific speed at which a hydrodynamic film pressure generated within the gap between the thrust runner and test GFTB is enough to support the applied static load, the thrust runner lifts off from the test GFTB and the friction mechanism changes from the boundary lubrication to the hydrodynamic lubrication. The experiment shows a series of lift-off test and load-carrying capacity test for two thrust runners with different surface roughnesses. For a constant static load of 15 N, thrust runner A with its lower surface roughness exhibits a higher start-up torque but lower lift-off torque than thrust runner B with a higher surface roughness. The load capacity test at a rotor speed of 60 krpm reveals that runner A results in a higher maximum load capacity than runner B. Runner A also shows a lower drag torque, friction coefficient, and bearing temperature than runner B at constant static loads. The results imply that maintaining a consistent surface roughness for a thrust runner may improve its static GFTB performance.

• Korean Journal of Applied Biomechanics
• /
• 제21권4호
• /
• pp.429-436
• /
• 2011

In this study, we have experimented with 9 players at the national delegate level. Although there were some differences in the average effects of 3 types of one-two straight movements after the application of wheel axle, there were no statistical differences in the case of surface reacting forces, electromyograms, and impact forces. When the right fist was impacted using the one-two straight movements and the wheel axle was applied with 3 segmentations, high impact forces were obtained for the pronation in the following order-72.01 $m/s^2$ (type 2), 70.93 $m/s^2$ (type 3), and 58.19 $m/s^2$ (type 1). Higher values of the surface reacting force were found for type 1 that did not exhibit pronation in the left foot, whereas in the case of the vertical direction of the right foot, type 2 with pronation exhibited higher values and impact forces. In the right electromyogram, high impact forces due to the activation of the muscular electric potential were obtained for lumbar erector (LE) spinae and triceps brachii (TB) with type 1; LE spina, latissimus dosi (LD), and upper trapezius (UT) with type 2; and brachioradialis (BR), UT, and rectus abdominal (RA) with type 3. Due to pronation and complex motions of the 3 pronation segmentations, the efficiency was higher for impacts due to one-two straight movements.

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권2호
• /
• pp.64-77
• /
• 1989

In this study, the experiments were carried out for the purpose of establishment of aluminium cementation to steel surface by diffusible heat treatment after making the coated film onto the substrate by arc spray method. Also, the microstructure and mechanical properties of the cementation layer produced by this study were inspected for various heat treatment and spraying conditions. Main results obtained are as follow ; 1. The coating film characteristics which have excellent errosion-resistance, high temperature oxidation-resistance are obtained by aluminium penetration heat treatment after making the sprayed aluminum coating film onto the steel substrate. 2. Aluminium diffusion penetration takes place at higher temperature than 660.deg.C, and the more heat treatment time and the higher heat treatment temperature adopted, the deeper diffusion layer obtained. 3. Insert gas arc spraying using argon gas as the carrier gas higher improvement of mechanical property than that of compressed air environment. 4. The coating film characteristics appeared to be improvement of adhesive property, porosity plugging effect by heat treatment in air environment.

• Journal of the Korean institute of surface engineering
• /
• 제51권4호
• /
• pp.249-255
• /
• 2018

High temperature and low temperature gaseous nitriding was performed in order to study of the surface hardening and wear properties of the nitrided AISI 410 Martensitic stainless steels. High temperature gaseous nitiridng (HTGN) was carried out using partial pressure $N_2$ gas at $1,100^{\circ}C$ for 10 hour, and Low temperature gaseous nitiridng (LTGN) was conducted in a gas mixture of NH3 and N2 at $470^{\circ}C$ for 10 hour. The nitrided samples were characterized by microhardness measurements, optical microscopy and scanning electron microscopy. The phases were identified by X-ray diffraction and nitrogen concentration was analyzed by GD-OES. The HTGN specimen had a surface hardness of about $700HV_{0.1}$, $350{\mu}m$ of case depth. A ${\sim}50{\mu}m$ thick, $1,250HV_{0.1}$ hard nitrided case formed at the surface of the AISI 410 steel by LTGN, composed nitrogen supersaturated expanded martensite and ${\varepsilon}-Fe_{24}N_{10}$ iron nitrides. Additionally, the results of the wear tests, carried out LTGN specimen was low friction coefficient and high worn mass loss of ball. The increase in wear resistance can be mainly attributed to the increase in hardness and to the lattice distortion caused by higher nitrogen concentration.