• Macromolecular Research
• /
• v.10 no.1
• /
• pp.2-12
• /
• 2002

The small-angle X-ray scattering (SAXS) beamline BL4C1 at the 2.5 GeV storage ring of the Pohang Accelerator Laboratory (PAL) has been in its first you of operation since August 2000. During this first stage it could meet the basic requirements of the rapidly growing domestic SAXS user community, which has been carrying out measurements mainly on various polymer systems. The X-ray source is a bending magnet which produces white radiation with a critical energy of 5.5 keV. A synthetic double multilayer monochromator selects quasi-monochromatic radiation with a bandwidth of ca. 1.5%. This relatively low degree of monochromatization is sufficient for most SAXS measurements and allows a considerably higher flux at the sample as compared to monochromators using single crystals. Higher harmonics from the monochromator are rejected by reflection from a flat mirror, and a slit system is installed for collimation. A charge-coupled device (CCD) system, two one-dimensional photodiode arrays (PDA) and imaging plates (IP) are available its detectors. The overall performance of the beamline optics and of the detector systems has been checked using various standard samples. While the CCD and PDA detectors are well-suited for diffraction measurements, they give unsatisfactory data from weakly scattering samples, due to their high intrinsic noise. By using the IP system smooth scattering curves could be obtained in a wide dynamic range. In the second stage, stating from August 2001, the beamline will be upgraded with additional slits, focusing optics and gas-filled proportional detectors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.46-48
• /
• 1988

The effect of cold reduction ratio on magnetic properties of 45% Ni-Fe permalloy was studied. To know the relationship between the crystal orientation and the magnetic properties, the pole figure was measured by X-ray diffraction method. In the case of single rolled reduction, the coercive force decreased with cold reduction ratio monotonically, but the maximum permeability, induction and squreness increased drastically. In the case of double rolled reduction (total reduction ratio is 90%), the saturation and residual induction increased slightly with secondary reduction ratio, but the maximum permeability and the coercive force had the maximum and the minimum value at the 50/50% reduction ratio respectively. And strong {100} <100> pole was developed by increasing the cold reduction ratio.

• Journal of Magnetics
• /
• v.17 no.1
• /
• pp.6-8
• /
• 2012

M$\ddot{o}$ssbauer spectra of hexagonal $BaFe_{12}O_{19}$ single crystals were studied at various temperatures (4-300 K). It was found that the spin states in Fe atoms were parallel to the ${\gamma}$-ray's direction into a single crystal along the caxis. The location of the Fe ion in the 2b site is unusual in an oxide structure and has strong anisotropic lattice vibrations. Moreover, at room temperature, the zero absorption lines of the Fe ions at the 2b site were observed due to fast diffusion motion in a double well atomic potential. The two Fe ions of the single crystal mainly enter into the sites in the mirror plane of the trigonalbipyramidal structure.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1816-1821
• /
• 2003

The sapphire wafer for blue light emitting device was manufactured by the implementation of the chemical and mechanical polishing process. The surface polishing of crystalline sapphire wafer was characterized by zeta potential measurement. The reduction process with the alkali slurry provides the surface chemical reaction with sapphire atoms. The poly-urethane pad also provides the frictional force to take out the chemically-reacted surface layers. The surface roughness was measured by the atomic force microscope and the crystalline quality was characterized by the double crystal X -ray diffraction analysis.

• 보존과학연구
• /
• s.26
• /
• pp.41-56
• /
• 2005

A set of horse bit from the Eonnam-ri site consists of three parts, pyo , ham , andinsu , and each part takes a shape of a piece of bar. According to current typological study, the pyo is S type, the insu is two-braided line type, and the outer rim of the ham is double rim type, respectively. According to X-ray test, inlaid design seems to have been decorated on the whole surface of the iron bit, originally. However, inlaid pattern partially remained. While the part of bit stopper is designed with flame pattern, the part of rein joint is designed with cloud pattern. According to XRF and XGT analysis of inlaid material, the content of silver is not more than 50%. The line inlay method making grooves on the surface of iron, then in laying a silver thread into them, and grinding the surface in a direction was adoptedin the manufacture of the iron bit.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.573-576
• /
• 2015

Recent discovery of $2M_{\odot}$ neutron stars in white dwarf-neutron star binaries, PSR J1614-2230 and PSR J0348+0432, has given strong constraints on the maximum mass of neutron stars. On the other hand, all well-measured neutron star masses in double neutron star binaries are still less than $1.5M_{\odot}$. These observations suggest that the neutron star masses in binaries may depend on the evolution process of neutron star binaries. In addition, recent works on LMXB (low-mass X-ray binaries) provides us the possibility of estimating the masses and radii of accreting neutron stars in LMXBs. In this talk, we discuss the implications of recent neutron star observations to the neutron star equation of states and the related astrophysical problems. For the evolution of neutron star binaries, we also discuss the possibilities of super-Eddington accretion onto the primary neutron stars.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.85-91
• /
• 2004

The sapphire wafers for blue light emitting devices were manufactured by the implementation of the surface machining technology based on micro-tribology. This process has been performed by chemical and mechanical polishing process. The sapphire crystalline wafers were characterized by double crystal X-ray diffraction. The sample quality of sapphire crystalline wafer at surfaces has a full width at half maximum of 89 arcsec. The surfaces of sapphire wafer were mechanically affected by residual stress during the polishing process. The wave pattern of optical interference of sapphire wafer implies higher abrasion rate in the edge of the wafer than its center from the Newton's ring.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.136-137
• /
• 2006

The stochiometric mix of evaporating materials for the $ZnGa_2Se_4$ single crystal thin films were prepared from horizental furnace. To obtains the single crystal thin films, $ZnGa_2Se_4$ mixed crystal were deposited on throughly etched Si(100) by the Hot Wall Epitaxy (HWE) system. The temperates of the source and the substrate were $590^{\circ}C$ and $450^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the double crystal X-ray diffraction(DCXD). Hall effect on this sample was measured by the method of van der Pauw and studied on carrier density and mobility dependence on temperature.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.575-578
• /
• 1995

X-ray magnetic-circular-dichroism (MCD) spectra, orbital ($$) and spin magnetic moments ($$) for Co(110) monolayers a free standing mode or sandwiched between Pd(Pd/1Co/Pd)and Cu layers (Cu/1Co/Cu) are calculated using the thin film full potential linearized augmented plane wave energy band method. In contrast to the double peak structure predicted for the Co(0001) surface, only a minor side peak is found in the MCD spectra for Cu/Co/Cu, while MCD spectra for the other systems show a single peak structure. The MCD sum rules originally derived from a single ion model are found in the band approach to be valid for the systems investigated. However, for the spin sum rule, the magnetic dipole term ($$) is not negligible and needs to be included.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.470-475
• /
• 1999

ZnS and ZnTe epilayers were grown on GaAs(100) GaP(100) substrates by hot-wall eitaxy. X-ray diffraction revealed that the epilayers have zinc-blende structure and were grown in (100) direction. The small values of the full width at half maximum (FWHM) of double crystal rocking curve (DCRC) showed high quality of the epilayers. From the thickness dependence of the FWHM of DCRC, the strain remaining in films is found to be due to the thermal expansion difference as well as due to the lattice mismatch.