• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.334-337
• /
• 1996

Si anisotropic etching is a key technology for micromachining. The main advantages of tetramethyl ammonium hydroxide (TMAH)-based solution are their full compatibility with IC process. In this work the anisotropic etching of single crystal Si in a TMAH (($CH_3$)$_4$NOH) based solution was studied. The influence of the addition of IPA to TMAH solution on their etching characteristics was also presented. The crystal planes bounding the etch front and their etch rates were determined as a function of temperature, crystal orientation, and etchant concentration. The etch rates of (100) oriented Si crystal planes decreased linearly with increasing the IPA concentration, The etched (100) planes were covered by Pyramidal-shaped hillocks below 15 wt.%, but very smooth surfaces were obtained above 20 wt.%. The addition of IPA to TMAH solution leads to smoother surfaces of sidewalls etched planes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.171-174
• /
• 2016

The diamond wire sawing method to produce silicon wafers for the photovoltaic application is still a new and highly investigated wafering technology. This technology, featured as the higher productivity, lower wear of the wire, and easier recycling of the coolant, is expected to become the mainstream technique for slicing the silicon crystals. However, the saw marks on the wafer surface have to be investigated and improved. This paper discusses the removal of saw marks on diamond wire-sawn single crystalline silicon wafer. With a pretreatment step using tetramethyl ammonium hydroxide ($(CH_3)_4NOH$, TMAH) and conventional texturing process with KOH solution (1 % KOH, 8 % IPA, and DI water), the saw marks on the surface of the diamond wire-sawn silicon wafers can be effectively removed and they are invisible to naked eyes completely.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.98-103
• /
• 2012

Poly(2,6-dimethyl-1,4-phenylene ether) (PPE) was synthesized using $Cu(NO_2)_2{\cdot}3H_2O$ or CuCl catalyst with various amounts of ligand and base in several different solvent systems. CuCl/1-methylimidazole/ammonium hydroxide was found to be an effective catalyst system which showed the highest polymer yield and molecular weight. The effects of catalyst/monomer ratio, different amine ligands, and the content of mono-functional reagent 2,4,6-trimethylphenol (TMP) additive on the polymer yield and molecular weight were investigated. Among the co-solvent systems used in this polymerization, chloroform/methanol 9/1(v/v) gave the highest polymer yield and molecular weight ($\overline{M_n}$ 55 K, $\overline{M_w}$ 92 K, PDI 1.7). The catalytic activity between CuCl and CuI was compared by oxygen-uptake experiments and the formation of sideproduct, 5,5'-tetramethyl-4,4'-diphenoquinone (DPQ), was analyzed by ultraviolet spectroscopy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.223-227
• /
• 2001

In this paper, the authors present the fabrication of high-yield Si thin-membranes by electrochemical etch-stop in tetramethyl ammonium hydroxide (TMAH): isopropyl alcohol (IPA):pyrazine solutions. The current-voltage (I-V) characteristics of n- and p-type Si in TMAH:IPA;pyrazine solutions were analysed, repsectively. Open circuit potential (OCP)and passivation potential (PP) of n- and p-type Si, respectively, were obtained and applied potential was selected between n- and p-type Si PPs. The electrochemical etch-stop method was applied to the fabrication of 801 micro-membranes with 20.0 $\mu\textrm{m}$ thickness on a 5" Si wafer. The average thickness of fabricated 801 micro-membranes on one wafer 20.03$\mu\textrm{m}$ and the standard deviation was ${\pm}$0.26$\mu\textrm{m}$. The Si surface of the etch-stopped micro-membranes was extremely flat with no noticeable taper or nonuniformity. The results indicate that use of the electrochemical etch-stop method for the etching of Si in TMAH:IPA;pyrazine solutions provides a powerful and versatile alternative process for fabricating high-yield Si micro-membranes.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.2
• /
• pp.26-31
• /
• 2001

This paper presents the electrochemical etch-stop characteristics of single-crystal Si(001) wafers in tetramethyl ammonium hydroxide(TMAH):isopropyl alcohol(IPA):pyrazine solutions. The addition of pyrazine to TMAH:IPA solutions increased the etch rate of (100) Si, thus the etching time required by the etch-stop process shortened. The current-voltage(I-V) characteristics of n- and p-type Si in TMAH:IPA:pyrazine solutions were obtained, respectively. Open circuit potential(OCP) and passivation potential(PP) of n- and p-type Si, respectively, were obtained and applied potential was selected between n- and p-type Si PPs. The electrochemical etch-stop method was used to fabricate 801 microdiaphragms of 20 ${\mu}{\textrm}{m}$ thickness on a 5-inch Si wafer. The average thickness of fabricated 801 microdiaphragms on one Si wafer was 20.03 ${\mu}{\textrm}{m}$ and the standard deviation was $\pm$0.26 ${\mu}{\textrm}{m}$. The Si surface of the etch-stopped microdiaphragm was extremely flat with no noticeable taper or nonuniformity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.584-584
• /
• 2012

결정형 실리콘 태양전지 공정 중 표면 texturing 공정은 표면에 요철을 형성시켜 반사되는 빛 손실을 줄여서, 증가된 빛 흡수 양에 의해 단락전류(Isc)를 증가시키는데 그 목적이 있다. 표면 texturing 공정은 습식 식각과 건식 식각에 의한 방법으로 나눌 수 있다. 습식 식각은 KOH, TMAH, HNA 등의 실리콘 식각 용액을 사용하여 공정상의 위험도가 크고, 사용 후 용액의 폐기물에 의한 환경오염 문제가 있다. 건식 식각은 습식 식각과 달리 폐기물의 처리가 없고 미량의 가스를 이용한다. 그리고 다결정 실리콘 웨이퍼처럼 불규칙적인 결정방향에도 영향을 받지 않는 장점을 가지고 있어서 건식 식각을 이용한 표면 texturing 공정에 관한 많은 연구가 진행되고 있으며, 특히 RIE(reactive ion etching)를 이용한 태양전지 texturing 공정이 가장 주목을 받고 있다. 하지만 기존의 RIE를 이용하여 표면 texturing 공정을 하게 되면 500 nm 이하의 needle-like 구조의 표면이 만들어진다. Needle-like 구조의 표면은 전극을 형성할 때에 접촉 면적이 좁기 때문에 adhesion이 좋지 않은 것과 단파장 대역에서 광 손실이 많다는 단점이 있다. 본 논문에서는 기존의 RIE texturing의 단점을 보완하기 위해 챔버 내부에 metal-mesh를 장착한 후 RIE를 이용하여 $1{\mu}m$의 피라미드 구조를 형성하였고, RIE 공정 시 ion bombardment에 의한 표면 손상을 제거(RIE damage remove etching)하기 위하여 10초간 TMAH(Tetramethyl -ammonium hydroxide, 25 %) 식각 공정을 하였다.

• Journal of Sensor Science and Technology
• /
• v.19 no.4
• /
• pp.291-296
• /
• 2010

Recently, recycling method of waste wafer has been an area of solar cell to cut costs. Micro_blasting is one of the promising candidates for recycling of waste wafer due to their extremely simple and cost-effective process. In this paper, we attempt to explore the effect of micro_blasting and DRE(damage removal etching) process for solar cell. The optimal process conditions of micro_blasting are as follows: $10{\mu}m$ sized $Al_2O_3$ powder, jetting pressure of 400 kPa, and scan_speed of 30 cm/s. And the particles formed on micro_blasted wafer were removed by DRE precess which was performed by using HNA(HF/$HNO_3$/$CH_3COOH$) and TMAH(tetramethyl ammonium hydroxide). Structural analysis was done using a-step and the XRD patterns.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.617-622
• /
• 2010

We have studied methods to save Si source during the fabrication process of crystalline Si solar cells. One way is to use a thin silicon wafer substrate. As the thickness of the wafers is reduced, mechanical fractures of the substrate increase with the mechanical handling of the thin wafers. It is expected that the mechanical fractures lead to a dropping of yield in the solar cell process. In this study, the mechanical properties of 220-micrometer-solar grade Cz p-type monocrystalline Si wafers were investigated by varying saw-damage etching conditions in order to improve the flexural strength of ultra-thin monocrystalline Si solar cells. Potassium hydroxide (KOH) solution and tetramethyl ammonium hydroxide (TMAH) solution were used as etching solutions. Etching processes were operated with a varying of the ratio of KOH and TMAH solutions in different temperature conditions. After saw-damage etching, wafers were cleaned with a modified RCA cleaning method for ten minutes. Each sample was divided into 42 pieces using an automatic dicing saw machine. The surface morphologies were investigated by scanning electron microscopy and 3D optical microscopy. The thickness distribution was measured by micrometer. The strength distribution was measured with a 4-point-bending tester. As a result, TMAH solution at $90^{\circ}C$ showed the best performance for flexural strength.