• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.37 no.6
• /
• pp.499-505
• /
• 1992

This experiment was carried out to find out the optimum application method of slow-release fertilizer under different soil textures, clay loam(Deogpyeong series), sandy loam (Gangseo series) in the southern region(Milyang, Kyeongnam) of Korea. The fertilizers used were Chosun slow-release fertilizer(silicate latex coated fertilizer: N-P$_2$O$_{5}$-K$_2$O=18-12-13) and Meister 15 (thermoplastic resin coated fertilizer : N-P$_2$O$_{5}$-K$_2$O=14-14-14). The two whole basal application methods such as side band placement at transplanting time of rice plant(cv.Donghaebyeo) and incorporation with soil as basal were tested. The released amount of ammonium nitrogen from the soils for 4 days submerged was 95ppm in sandy loam and 60ppm in clay loam. The greenish degree of rice leaf was higher at the whole plow layer placement method than the others. The nitrogen efficiencies of the fertilizers were Meister 15 > convention > Chosun in order and between the application methods were similiar. The growth status was better at the whole plow layer placement application method of Meister 15 regardless of soils and seedling ages. The ripening ratio was increased at slow-release fertilizer application, and between application methods, whole plow layer placement was lower because of lodging damage. The yield in clay loam soil showed a significant difference between the ferilizers, but there were slight differences between the application methods and fertilizers in sandy loam soil. As a result, the slow-release fertilizer, Meister 15, applied at the whole layer showed a good rice growth and seemed a plausible fertilizing method.

• Economic and Environmental Geology
• /
• v.53 no.3
• /
• pp.287-296
• /
• 2020

Mine Reclamation Project is being carried out with the aim of ensuring a sustainable green living and helping to develop eco-friendly mines by analyzing, removing and preventing the harmful factors. Mines developed during the japanese colonial period and mining boom period are still not repaired throughout the country, and from these scattered risks, public safety is worth pursuing as a top priority. The project that is close to public safety in the mine recalmation project is an emergency treatment, and the most widely used method is a filling method similar to the ground subsidence prevention. If dangerous mine cavity or tunnels are located in the mountains, charging with existing materials may not be possible, or unreasonable cases may occur, and new methods of technological development are required. Emergency actions should be carried out safely and efficiently to prevent the loss of precious people's lives on the hiking paths adjacent to dangerous mining sites. In these field conditions, urethane foam materials may be an alternative. In this study, the applicability of urethane foam materials in mining was reviewed through overseas cases. It was also tested on the appropriate depth of top soil for the protection of urethane foam materials through forest fire simulation test. The test result show that approximately 15cm of soil covering (recommended 20cm over) was suitable for maintaining the function of foam materials from forest fires.

• Korean Journal of Digital Imaging in Medicine
• /
• v.16 no.2
• /
• pp.9-14
• /
• 2014

Purpose: The purpose of this study has attempted to evaluate and compare the image evaluation and exposure dose by respectively applying Filtered Back Projection(FBP), the existing test method, and Adaptive Statistical Iterative Reconstruction(ASIR) with different values of tube voltage during the Low Dose Computed Tomography(LDCT). Materials and Methods: With the image reconstruction method as basis, Chest Phantom was utilized with the FBP and ASIR set at 10%, 20% respectively, and the change of Tube Voltage (100kVp, 120kVp). For image evaluation, Back ground noise, Signal to Noise ratio(SNR) and Contrast to Noise ratio(CNR) were measured, and, for dose evaluation, CTDIvol and DLP were measured respectively. The statistical analysis was tested with SPSS(ver. 22.0), followed by ANOVA Test conducted after normality test and homogeneity test. (p<0.05). Results: In terms of image evaluation, there was no outstanding difference in Ascending Aorta(AA) SNR and Infraspinatus Muscle(IM) SNR with the different values of ASIR application(p<0.05), but a significant difference with the different amount of tube voltage(p>0.05). Also, there wasn't noticeable change in CNR with ASIR and different amount of Tube Voltage (p<0.05). However, in terms of dose evaluation, CTDIvol and DLP showed contrasting results(p<0.05). In terms of CTDIvol, the measured values with the same tube voltage of 120kVp were 2.6mGy with No-ASIR and 2.17mGy with 20%-ASIR respectively, decreased by 0.43mGy, and the values with 100kVp were 1.61mGy with No-ASIR and 1.34mGy with 20%-ASIR, decreased by 0.27mGy. In terms of DLP, the measured values with 120kVp were $103.21mGy{\cdot}cm$ with No-ASIR and $85.94mGy{\cdot}cm$ with 20%-ASIR, decreased by $17.27mGy{\cdot}cm$(about 16.7%), and the values with 100kVp were $63.84mGy{\cdot}cm$ with No-ASIR and $53.25mGy{\cdot}cm$ with 20%-ASIR, a decrease by $10.62mGy{\cdot}cm$(about 16.7%). Conclusion: At lower tube voltage, the rate of dose significantly decreased, but the negative effects on image evaluation was shown due to the increase of noise. For the future, through the result of the experiment, it is considered that the method above would be recommended for follow-up patients or those who get health checkup as long as there is no interference on the process of diagnosis due to the characteristics of Low Dose examination.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.55-55
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.56-63
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Science of Emotion and Sensibility
• /
• v.20 no.1
• /
• pp.95-104
• /
• 2017

This study aims to develop a reliable and valid Geriatric Reaction Inventory-Simplified Form (GRI-SF). Reaction inventory for measuring anger (Evans & Stangelang, 1971) is an assessment tool in a view of stimuli for measuring the level of anger invoked from the anger-triggered experiences. Yet, the inventory, comprised of 76 items, is sometimes incapable of finishing up the lengthy questionnaire. In the sense, a simplified form of RI is necessary for those lacks cognitive ability such as stroke patients or the elderly. In study 1, a full version of Reaction Inventory was given for the elder who are above 60, and ten items out of 76 was selected to form GRI-SF based on the psychometric theory. In study 2, the reliability and validity of GRI-SF was tested by another sample group of elderly with some additional examinations. The reliability was good with Cronbach's alpha of 0.79. Based on the fact that GRI-SF measures the personal trait anger, GRI-SF should not be only strong correlation with the scores of trait anger strongly, but be less correlated with scores representing other aspects of anger. As a result, GRI-SF score showed strong correlations with trait anger among other sub-categories of State-Trait Expression Inventory (STAXI), and was less correlated with anger-out score which reflects behavioral aspect of anger. Moreover, it is less correlated (r=.41) with hostility representing attitudinal or cognitive aspects of anger. Consequently, GRI-SF, constructed by this research, is verified to be a reliable and valid tool for anger measurement.

• Korean Journal of Food Science and Technology
• /
• v.40 no.1
• /
• pp.21-30
• /
• 2008

In this study, the antioxidant activities of 27 medicinal herbs and plants were measured. The dried medicinal herbs and plants were pulverized and extracted by water, 15% ethanol, and 45% ethanol, respectively at above $80^{circ}C$ for 90 minutes. The original and diluted extracts were tested for their antioxidant activities by 1,1-diphenyl-2-picrylhydrazyl (DPPH) free radical-scavenging activity assay. Cornus officinalis (C) and Scutellaria baicalensis (S) were selected to develop rice wines with higher antioxidant activities, based on the result of the 45% ethanol extraction. The rice wine developed using sample showed the highest antioxidant activity as comparing to those of other commercial rice wines. The rice wine samples were analyzed for titratable acidity, pH, $^{\circ}Brix$, reducing sugar content, color (L, a, b), amino-acidity, and ultraviolet absorption. The preferences for color, aroma, and overall acceptability were determined using a 9-point hedonic scale by 150 consumers. The sweetness, sourness, fruitiness, color, and medicinal herb-taste levels of the developed rice wines were also evaluated, using a 9-point just-about-right scale. The mean overall acceptability score of c (5.54) was higher than that of sample S. Based on the results, the sourness and medicinal herb-taste levels of sample s should be modified to higher levels, and the fruitiness of sample S also needs to be adjusted. For a future study, the final compositions of the developed rice wines will be adjusted for product launching based on the preference test data acquired in this study.

• Journal of Food Hygiene and Safety
• /
• v.31 no.4
• /
• pp.264-271
• /
• 2016

The purpose of this study was to investigate contamination sources of baby leafy vegetables by assessing microbial loads on baby leafy vegetables and agricultural inputs contacted with the vegetables. To estimate microbial loads, fecal indicators (coliform and Escherichia coli) and foodborne pathogens (E. coli O157:H7, Salmonella spp., Staphylococcus aureus, Listeria monocytogenes, and Bacillus cereus) were examined. A total of 126 samples including eleven kinds of leafy vegetables, irrigation water, media, and tools were tested, resulting in coliform contamination observed from most of samples. For E. coli, 10.3% (13/126) of the samples were positive including irrigation water, knife, handler, media, tools, and three kinds of leafy vegetables. B. cereus was detected from 38% (48/126) of the samples including media, tools and three kinds of leafy vegetables. No E. coli O157:H7, Salmonella spp., and L. monocytogenes was detected. This result implies that contacting with agricultural inputs could explain microbial load of baby leafy vegetables.

• Journal of Food Hygiene and Safety
• /
• v.35 no.1
• /
• pp.6-12
• /
• 2020

Prevalence of toxin genes and profiles of antibiotic resistance in Vibrio vulnificus were investigated for prevention of Vibrio sepsis and selection of effective antibiotics. A total of 23 V. vulnificus strains were isolated from Vibrio sepsis patients, fish, and water samples collected from fish tanks in restaurants in Jeonnam province during 2015-2017 period. Prevalence of toxin genes including, RtxA, viuB and vvhA were assessed and susceptibilities to 15 different antibiotics were determined. As a result of the toxin gene profile, the RtxA toxin gene was detected in 19 (82.6%) out of 23 strains, and vvhA and viuB toxin genes were positive in all strains. These results showed that V. vulnificus tested in this study possessed at least one more toxin gene, and the toxin gene detection rate was higher than in previous reports. Therefore, there is always a risk of Vibrio sepsis through eating fish or having contact with aquarium water at seafood restaurants. Especially, it was deemed necessary to provide preventive education about Vibrio sepsis for workers in such restaurants. The results of antibiotic susceptibility tests presented 94.4% resistance to cepoxitin antibiotics but all strains showed susceptibility to 14 kinds of antibiotics including chloramphenicol and tetracycline. The currents antibiotic therapy using chloramphenicol and teteracycline against Vibrio sepsis was judged to be useful.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.11-16
• /
• 1984

The backscattering cross sections of live fish and the probability density function of fish echoes were measured at side aspect. The measurements were made at 40 and 170 in KHz. The specimen fishes on the experiments were two catfish-total length of 16.8cm(L/λ is about 4.5, where the L is length, the λ is the sound wavelength) and 23cm(L/λ, ~6.1), a carp(Cyprinus carpio) of 17.5cm(L/λ, ~4.7), a Telapia(Tilapia mossambica)of 19.5cm(L/λ, ~5.2) and several fishes. Those lengths ranged from 10.7 to 24.0cm. The results of the measured maximum backscattering cross sections were 5.62$\times$10 super(-5) to 7.23$\times$10 super(-4) m super(2). Huang and clay reported that, when the fish was moving gently, the probaiblity density function of the fish echces was approximately the same with the Rayleigh probability density function. Thereafter Ehrenberg et al. also reported that the Rayleigh probability density function on fish was performed at the critical acoustic length ratio or more in theoretical base. Recently Dahl and Mathisen tested the Rayleigh probability density function on fish when the fish-length-to-wavelength ratios were greater than 100. In this paper the experimental result was also not accorded with the Rayleigh probability density function when the fish-length-to-wavelength rations were lower than the critical ratio.