• Journal of Korea Water Resources Association
• /
• v.48 no.7
• /
• pp.523-533
• /
• 2015

In this study, the effectiveness of overflow improvement of weir was tested by conducting hydraulic experiments at the designated spot for installment of side weir under the condition of installment of hydraulic structures such as small reservoir in mainstream. The height of the reservoir was set up as a third of that of the weir, accordingly the rate of the height of the weir and the distance of the reservoir from the weir($B_h/L_b$) were 0.05, 0.025, 0.0167 each. As a result, overflows per unit width increased by 8.1%, 5.4% and 3.9% perspectively. A new discharge coefficient that adds $B_h/L_b$ as parameter to the existing discharge coefficient of trapezoidal broad crested side weir was suggested and the application of the new formula of discharge coefficient by comparing measured overflow with calculated overflow was identified.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.4
• /
• pp.185-192
• /
• 2016

Low operational cost and high efficiency is absolute requirements in the mass production of the ship engine. Increasing the performance of the fuel injection system in the diesel engine is one kind of solution to improve the efficiency. Modern diesel engines are using electronic control module as the main controller in the fuel injection control system, however the mechanical system still involved in the modern control system. In modern ship engine, a control valve was used in injection fuel to regulate the flow of the fuel. High pressure and friction are intensively occur within this part, therefore high wear resist and low friction coefficient material including fine lubricating are needed. This study is to figure out the wear resist material and proper lubricant in the control valve fuel injection. The experiment has been tested using pin on disk in several treatments those are used various lubricants and non-lubricant condition. Two kinds of lubricant were used in this experiment such as INDERIN AW-32 and paraffin oil. INDERIN AW-32 has a better result compared to non-lubricant condition, which are 20% performance increases than non-lubricant condition. SCM 440 was providing small friction coefficient in the lower velocity. The friction coefficient was constantly maintains at 0.1 m/s of velocity or above respectively with the increment of the loads. Using INDERIN AW-32 and paraffin oil the lowest friction coefficient occurred at the lower load, and increases side by side with the increment of loads.

• Smart Structures and Systems
• /
• v.14 no.6
• /
• pp.1247-1267
• /
• 2014

Real-Time Hybrid Simulation (RTHS) is a novel approach conceived to evaluate dynamic responses of structures with parts of a structure physically tested and the remainder parts numerically modelled. In RTHS, delay estimation is often a precondition of compensation; nonetheless, system delay may vary during testing. Consequently, it is sometimes necessary to measure delay online. Along these lines, this paper proposes an online delay estimation method using least-squares algorithm based on a simplified physical system model, i.e., a pure delay multiplied by a gain reflecting amplitude errors of physical system control. Advantages and disadvantages of different delay estimation methods based on this simplified model are firstly discussed. Subsequently, it introduces the least-squares algorithm in order to render the estimator based on Taylor series more practical yet effective. As a result, relevant parameter choice results to be quite easy. Finally in order to verify performance of the proposed method, numerical simulations and RTHS with a buckling-restrained brace specimen are carried out. Relevant results show that the proposed technique is endowed with good convergence speed and accuracy, even when measurement noises and amplitude errors of actuator control are present.

• Advances in concrete construction
• /
• v.2 no.3
• /
• pp.177-192
• /
• 2014

One of the main applications of FRP composites is confining concrete columns. Hence identifying the cyclic and monotonic stress-strain behavior of confined concrete columns and the parameters influencing this behavior is inevitable. Two significant parameters affecting the stress-strain behavior are aspect ratio and corner radius. The present study aims to scrutinize the effects of corner radius and aspect ratio on different aspects of stress-strain behavior of FRP confined concrete specimens (rectangular, square and circular). Hence 44 FRP confined concrete specimens were tested and the results of the tests were investigated. The findings indicated that for specimens with different aspect ratios, the relationship between the ultimate stress and the corner radius is linear and the variations of the ultimate stress versus the corner radius decreases as a result of an increase in aspect ratio. It was also observed that increase of the corner radius results in increase of the compressive strength and ultimate axial strain and increase of the aspect ratio causes an increase of the ultimate axial strain but a decrease of the compressive strength. Investigation of the ultimate condition showed that the FRP hoop rupture strain is smaller in comparison with the one obtained from the tensile coupon test and also the ultimate axial strain and confined concrete strength are smaller when a prism is under monotonic loading. Other important results of this study were, an increase in the axial strain during the early stage of unloading paths and increase of the confining effect of FRP jacket with the increase and decrease of the corner radius and aspect ratio respectively, a decrease in the slope of reloading branches with cycle repetitions and the independence of this trend from the variations of the aspect ratio and corner radius and also quadric relationship between the number of each cycle and the plastic strain of the same cycle as well as the independence of this relationship from the aspect ratio and corner radius.

• Journal of the East Asian Society of Dietary Life
• /
• v.25 no.6
• /
• pp.990-998
• /
• 2015

The aim of this study was to examine the cytotoxicity and potential inhibitory effects from four types of edible domestic brown seaweeds, Undaria pinnatifida (UP), Laminaria japonica (LJ), Sargassum fulvellum (SF), and Hizikia fusiforme (HF), on preadipocyte differentiation in 3T3-L1 cell line. Water and ethanol extracts from the four types of seaweeds were prepared and tested for cell viability in the 3T3-L1 cell line by using MTT assay. In addition, various doses of the water extract of seaweeds (WES) and ethanol extract of seaweeds (EES) were treated at the beginning of 3T3-L1 differentiation and continued until the cells were fully differentiated to adipocytes. Oil Red-O staining was performed to determine the potential cell differentiation inhibitory effects of the WES and EES by measuring the levels of lipid droplet accumulation in 3T3-L1 adipocytes. $PPAR{\gamma}$ mRNA expression levels were significantly reduced by WESs of UP, LJ, and HF as well as EESs of LJ and HF. As a result, we observed the superior cell differentiation inhibitory effects of WES compared to that of EES in a dose-dependent manner without any significant cytotoxicity in mouse adipocytes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.89-97
• /
• 2016

This paper addresses the problem of the construction planning of artillery positions, for which we present an optimization model and propose a heuristic algorithm to solve problems of practical size. The artillery position construction plan includes the assignment of engineers to support the artillery and the schedule of the support team construction sequence. Currently, in the army, managers construct the plan based on their experience. We formulate the problem as a mixed integer program and present a heuristic that utilizes the decomposition of the mixed integer model. We tested the efficacy of the proposed algorithm by conducting computational experiments on both small-size test problems and large-size practical problems. The average optimality gap in the small-size test problem was 6.44% in our experiments. Also, the average computation time to solve the large-size practical problems consisting of more than 200 artillery positions was 79.8 seconds on a personal computer. The result of our computational experiments shows that the proposed approach is a viable option to consider for practical use.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.135-135
• /
• 2017

Greenhouse have been developed to provide the plants with good environmental conditions for cultivation crop, two major factors of which are the inside air temperature and humidity. The inside temperature are influenced by the heating systems, ventilators and for systems among others, which in turn are geverned by some type of controller. Likewise, humidity environment is the result of complex mass exchanges between the inside air and the several elements of the greenhouse and the outside boundaries. Most of the existing models are based on the energy balance method and heat balance equation for modelling the heat and mass fluxes and generating dynamic elements. However, greenhouse are classified as complex system, and need to make a sophisticated modeling. Furthermore, there is a difficulty in using classical control methods for complex process system due to the process are non linear and multi-output(MIMO) systems. In order to predict the time evolution of conditions in certain greenhouse as a function, we present here to use of recurrent neural networks(RNN) which has been used to implement the direct dynamics of the inside temperature and inside humidity of greenhouse. For the training, we used algorithm of a backpropagation Through Time (BPTT). Because the environmental parameters are shared by all time steps in the network, the gradient at each output depends not only on the calculations of the current time step, but also the previous time steps. The training data was emulated to 13 input variables during March 1 to 7, and the model was tested with database file of March 8. The RMSE of results of the temperature modeling was $0.976^{\circ}C$, and the RMSE of humidity simulation was 4.11%, which will be given to prove the performance of RNN in prediction of the greenhouse environment.

• Structural Engineering and Mechanics
• /
• v.67 no.5
• /
• pp.505-516
• /
• 2018

In this paper, the effects of particle size and model scale of concrete has been investigated on the failure mechanism of PFC2D numerical models under uniaxial compressive test. For this purpose, rectangular models with same particle sizes and different model dimensions, i.e., $3mm{\times}6mm$, $6mm{\times}12mm$, $12mm{\times}24mm$, $25mm{\times}50mm$ and $54mm{\times}108mm$, were prepared. Also rectangular models with dimension of $54mm{\times}108mm$ and different particle sizes, i.e., 0.27 mm, 0.47 mm, 0.67 mm, 0.87 mm, 1.07 mm, 1.87 mm and 2.27 mm were simulated using PFC2D and tested under uniaxial compressive test. Concurrent with uniaxial test, direct shear test was performed on the numerical models. Dimension of the models were $75{\times}100mm$. Two narrow bands of particles with dimension of $37.5mm{\times}20mm$ were removed from upper and lower of the model to supply the shear test condition. The particle sizes in the models were 0.47 mm, 0.57 mm, 0.67 mm and 0.77 mm. The result shows that failure pattern was affected by model scale and particle size. The uniaxial compressive strength and shear strength were increased by increasing the model scale and particle size.

• Journal of Venture Innovation
• /
• v.2 no.2
• /
• pp.1-19
• /
• 2019

Various studies have been conducted on factors influencing the adoption of new technologies. In particular, the factors influencing customers' acceptance of new technologies that emerged along with the arrival of the 4th Industrial Revolution. Theoretical models are mainly based on the technology acceptance model (TAM) or Extended Unified Theory of Acceptance and Use of Technology : UTAUT2). However, there are no trust variables in these models. In this study, we added trust variable and tested augmented reality(AR). Three types - trust as an independent variable, as a mediating variable, and as a moderating variable - were analyzed statistically. As a result, trust was most explanatory when viewed as a mediating variable between independent variables and intention to use. In theory, it has been shown that trust acts as a mediating effect. In practice, trust is most important in accepting new technologies, so it is important to prioritize trust.

• The Korea Journal of Herbology
• /
• v.22 no.2
• /
• pp.103-108
• /
• 2007

Objectives : A morphological classification among Pinelliae Tuber, Typhonii Flagelliformis Rhizoma and Arisaematis Rhizoma was made through microscopic observation. Method : The slice of the tested material made by paraffin section technique was colored with Safranine Malachite Green contrast methods, and then observed and photographed by olymphus-BHT. Result : 1. Pinelliae Tuber is like a ball with a $1{\sim}1.5cm$ diameter, with a concave apex and pockmarked root trace around. 2. Typhonii Flagelliformis Rhizoma is somewhat oval or like a cone, with a $4{\sim}8mm$ diameter, a $7{\sim}15mm$ height, a projected round apex, and a pin-pointed back. 3. Arisaematis Rhizoma is somewhat flat round with a $2{\sim}2.5cm$ diameter, a little than Pinelliae Tuber, and its apex has incomplete lobopodium and root trace. 4. Fundamental tissues of Pinelliae Tuber, Typhonii Flagelliformis Rhizoma, and Arisaematis Rhizoma have starch grains and mucilage cells, and their mucilage cells include the raphides of calcium oxalate. Conclusion : Internal forms of Pinelliae Tuber, Typhonii Flagelliformis Rhizoma, and Arisaematis Rhizoma are difficult to distinguish from one another, but Pinelliae Tuber and Arisaematis Rhizoma can be distinguished by their external forms and sizes, and Pinelliae Tuber and Typhonii Flagelliformis Rhizoma were distinguished by the forms of apex.