• 한국안전학회지
• /
• 제28권1호
• /
• pp.18-23
• /
• 2013

The purpose of this study were to develop and validate a prototype slipmeter used on-site floor. The developed slipmeter was dreg sled type. It measured static coefficient of friction(SCOF). The developed slipmeter was evaluated with ASTM 2508-11 which use four different standard surfaces(polished granite, glazed porcelain, vinyl composite tile, and ceramic tile). The SCOF was then measured with developed slipmeter under the three different contaminants and seven different floors. The test results of slipmeter were also compared with those of BOT-3000, floor surface roughness, and human perception. The test results revealed that developed slipmeter successfully ranked all four standard surfaces and differentiated among standard surfaces with varying degrees of slipperiness. The developed slipmeter couldn't properly measure slipperiness under the two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol). The test results of developed slipmeter had stronger correlation with those of BOT-3000 and floor roughness under the water and detergent solution than under the glycerol. The test results of developed slipmeter also showed stronger correlation with those of BOT-3000 and surface roughness than those of human perception. The newly developed slipmeter had been found to give consistent results under the test conditions except for two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol).

• 한국농공학회논문집
• /
• 제46권1호
• /
• pp.27-34
• /
• 2004

A model test is carried out to investigate flow-induced vibration of a Tainter gate in estuary sulices. The gate model scaled with the ratio of 1：25 is made of acryl panel dimensioned 0.66m in width, 0.5m in height in the concrete test flume. Firstly, natural frequencies of the model gate are measured and the results are compared with the numerical results in order to verify the model. The amplitudes of the vibration are measured under the different gate opening and water level conditions in flow from the gate outside to the gate inside. Also 5 revised gate models with bottom width increased 0.5 cm each are tested under the different gate opening and water level. The results are analyzed to study the characteristics of the gate vibration. These test results are assessed in comparison with formerly test results, as a result, presents a design method of Tainter gate to reduce the gate vibration and a basic data for the guide manuals of gate management.

• Steel and Composite Structures
• /
• 제25권6호
• /
• pp.705-716
• /
• 2017

The objective of this study is to investigate the actual behavior of studs in structures under earthquake load through laboratory tests and numerical simulation. A test program including eighteen specimens was devised with consideration of different concrete strengths and stud diameters. Six of specimens were subjected to monotonically increasing loading while the others were subjected to cyclic loading. Mechanical behavior including the failure mechanism, load-slip relationship, stiffness degradation, energy dissipation and the damage accumulation was obtained from the test results. An accurate numerical model based on the ABAQUS software was developed and validated against the test results. The results obtained from the finite element (FE) model matched well with the experimental results. Furthermore, based on the experimental and numerical data, the design formulas for expressing the skeleton curve were proposed and the simplified hysteretic model of load versus displacement was then established. It is demonstrated that the proposed formulas and simplified hysteretic model have a good match with the test results.

• 동아시아경상학회지
• /
• 제10권1호
• /
• pp.95-108
• /
• 2022

Purpose - This study attempts a multifaceted analysis utilizing the Chinese test takers' results of the Economy & Business Aptitude Test. Since Chinese students study socialist theories of economics along with market-based ones, comparing Chinese university students' basic knowledge of economics and business and its application to those of Korean test takers is also very meaningful from the perspective of economics education research. Research design, data, and methodology - This study investigates the results on the test of economy and business understanding between Korea and China. For comparison of the result, we conducted MK-TEST for two universities in China. Result - This study finds that the average correct answer rate of Korea is higher than one of China according to the overall results. The average difference rate is about 15% between Korea and China. More concretely, the correct answer rate of business area is higher than one of economy area, identifying them by subject area. Conclusion - According to the results, this study can infer that there are no or little differences in the ability of examinee to solve applied questions between Korea and China and the differences of the scope and emphasis point in an academic curriculum between both countries might bring these kinds of results. Finally, Chinese students shows higher correct answer rate to the questions about the economy issues and policies related to China than one of Korea examinee.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.671-680
• /
• 2003

The accuracy of inflow into tunnel estimates depends largely on how well permeability is characterized. But, the average of the packer test results will always underestimate the upper end of the permeability range, and therefore underestimate the inflow. Taking an average of the test results always underestimates inflow because the average permeability does not really exist. The distribution of packer-test data may not accurately reflect permeability, however, due to the limits of the test method and the luck of the field investigation. These discrepancies may be overcome by using Raymer(2001)'s log-normal plots and Heuer(1995)'s histograms of the data to develop a permeability model that will be used in lieu of the data to calculate inflow. Furthermore, the influence on the inflow is examined by the geological characteristics based upon the hundred times of packer test OO tunnel project.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.137-140
• /
• 2000

In this paper, we have proposed an efficient test generation method for asynchronous circuits. The test generation is based on specification level, especially on Signal Transition Graph(STG)〔1〕 which is a kind of specification method for asynchronous circuits. To conduct a high-level test generation, we have defined a high-level fault model, called single State Transition Fault(STF) model on STG and proposed a test generation algorithm for STF model. The effectiveness of the proposed fault model and its test generation algorithm is shown by experimental results on a set of benchmarks given in the form of STG. Experimental results show that the generated test for the proposed fault model achieves high fault coverage over single input stuck-at fault model with low cost. We have also proposed extended STF model with additional gate-level information to achieve higher fault coverage in cost of longer execution time.

• 패션비즈니스
• /
• 제14권1호
• /
• pp.176-183
• /
• 2010

The purpose of this study is to examine the antibacterial activity and deodorization of fabrics dyed with pine needles extract. The microbes used for a test were two kinds of bacteria and two kinds of fungi. The test results showed as follows. In the test results of antimicrobial activity, both cotton and silk fabrics showed the antimicrobial rate of over 90% after washing three times. In the test result of antifungal activity, all fabrics didn't show any effective antifungal activity. In the test result of deodorization, the dyed cotton fabric showed the higher rate of deodorization than the non-dyed fabric, and the fabric showed the highest rate of deodorization was the test fabric mordanted by Fe and the rate of deodorization showed 92%. In case of silk fabric, the fabric showed the highest rate of deodorization was the test fabric mordanted by Al, and the rate of deodorization showed 92%.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권2호
• /
• pp.118-124
• /
• 2016

Purpose: The purpose of this paper is to suggest an environmental test plan for reducing early failure. Methods: We study the preferred test design and tests that are performed substantially in the company. We investigate the environmental profile on the actual supply chain and identify the effectiveness for this test design. Results: Proposed sequential test designed to implement the supply chain on the environment profile showed more effective results compared to existing tests. Conclusion: Suggested sequential test in this paper will be an effective guidance for the given environment test.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1024-1029
• /
• 2008

In this study, new parameter related with compression index was derivated from piezocone test results. It is assumed that the consolidation coefficient obtained by piezocone test is concerned with the volume change during piezocone dissipation. Based on that assumption, new parameter in terms of consolidation coefficient from piezocone test was introduced. The new parameter from piezocone test and the compression index from laboratory consolidation test shows linear relationship.

• 대한핵의학회지
• /
• 제14권1호
• /
• pp.17-21
• /
• 1980

TRH stimulation tests and $T_3$ suppression tests were done in 13 patients with clinically suspected mild or early hyperthyroidism who were all conventional thyroid function tests gave results within the accepted normal range. The results were as follows 1. 6 patients with normal $T_3$ suppression test revealed normal TRH stimulation test and could be easily diagnosed as euthyroidism. 2. 7 patients with abnormal $T_3$ suppression test exhibited no TSH response to TRH stimulation test and could be easily diagnosed as hyperthyroidism. The TRH stimulation test is a single, sensitive and reliable test of thyroid function and can well replace $T_3$ suppression test in the diagnosis of marginal hyperthyroidism.