• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.5
• /
• pp.743-752
• /
• 2013

The objective of this study was to investigate the quality characteristics of spirits derived from fruit using copper distillation equipment. First, optimal yeast strains were chosen through a fermentation test on raw materials (apples, mandarins and rowanberries). The normal fermentation condition for rowanberries observed at a rowanberry concentration of 8% during mashing included chaptalization with sugar to increase the alcohol content. During the mashing, fruits were fermented and distilled through one of three different types of distillation apparatuses (pot distiller, vacuum distiller, or multistage distiller made of copper). The results revealed that the type of apparatus used affects the content of alcohol and flavor components. The distilled spirits prepared through a copper multistage distiller had a much higher tendency to retain components of fruit aromas such as ethyl acetate and provided higher yields than spirits prepared with a pot distiller or vacuum distiller. Thus, the copper multistage distiller apparatus can be applied to positively influence the taste and flavor of fruit distilled spirits by enhancing fruit aromas, removing impurities such as sulfur components and enhancing yields.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.219-225
• /
• 2020

With the aging population, the prevalence of musculoskeletal disorders in the elderly continues to increase. In addition, musculoskeletal disorders are the third most common social and economic loss among occupational illnesses in Workers' compensation insurance benefits as of 2015 standard and are also common among workers. In this study, a vest that can assist in the prevention and treatment of musculoskeletal disorders of the waist was produced, and it is intended to confirm the presence or absence of the effect through experiments. Diseases of the waist are closely related to core muscles. Therefore, the produced vest was made in a form that supports the core muscles. Before and after wearing the vest for effectiveness verification, the While performing 10-times of the Mackenzie exercises, a waist extension exercise, collected the EMG data of the internal oblique, Rectus abdominis, and Erector spinae, which correspond to the core muscles. The collected data were analyzed through the electromyography analysis program RM-3 to obtain RMS values for 10-times measurements of each muscle and to compare the average values. After comparing the data, to verify the significance, the technical statistical value of the measurement result was calculated and the average difference was verified through PASW ver18.0, And the paired t-test is performed on the experimental results to perform statistical processing. and Statistical processing was performed by setting the significance level to α=.05.

• Journal of Navigation and Port Research
• /
• v.29 no.5 s.101
• /
• pp.395-402
• /
• 2005

The most important point when we engage on waterway dredging work is supplying safe navigational passage to the vessels underway by narrowing dredge work area and removing submerged dangers. In order to meet this end it is necessary to use auxiliary equipment for shifting actively and mooring and adopt automation of dredging work by integrating information on real time position, dredging depth, and work information. The dredger with a spud control system in this study, by the way, is able to employed on continuous dredging work with the narrowest working area allowing wide and safe passages to vessels underway, by moving the dredger to the working zone with the spud controlled automatically. Furthermore, it has been improved definitely compared with the existing dredging process management system such that it shows the track of spud and working depth on the electronic navigation chart of window, together with the final outcome of dredging work. The test dredging work at the entrance of Busan North Port for system evaluation showed that actual working time available was twice of the one by the existing anchor system, and that it reduced $38\%$ of time for preparation work and one man power.

• Journal of Korean Physical Therapy Science
• /
• v.19 no.3
• /
• pp.49-56
• /
• 2012

Background : The purpose of this study is to understand the effects of ankle joint taping on balancing abilities of the elderly and to provide preliminary data on preventing falls among the elderly. Methods : In this study, 20 students(8 male, 12 female) in their 20s from D University as well as 14 elderly(4 male, 10 female) in their 70s from S community center have participated. The participants were well informed about the experiment and voluntarily participated. We measured the difference in balancing ability before and after taping between the two groups using methods such as standing on single-leg stance, TUG, and plantar pressure. Kinesio taping, a stop-watch, and the EMED-system were used as equipment along with the SPSS 12.0 program, with a significance level of 0.05, to test the difference before and after taping between the two groups. Result : First, the 70s group showed a significant increase in the dorsal flexion angle after taping. Second, the 70s group showed a significant increase in duration time of standing on one foot after taping. Third, the 70s group's TUG time was significantly shorter. Fourth, the maximum peak value for static and dynamic plantar pressure showed a significant decrease after taping; and dynamic plantar pressure area value decreased as well within significant range. Conclusion : The study has shown that taping is effective on static dynamic balancing ability of the elderly.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.3-8
• /
• 2009

The traction system has been mainly used for rehabilitation and correction of patients with spine or gait diseases in orthopedics or at home. Some problems could occur in human body when patients forced their training using the traction system. So it needs to measure a traction force and control the training time. However, most of products on market have no sensor measuring traction force. Thus we designed and made a sensor detecting traction force using strain gauge, amplifier for transition to output signal and experiment devices for performance test. We carried out experiment of a sensor detecting a traction force and measured electric responses of it with respect to traction loads. Maximum error was within about 1% for experiments in static condition and the average error was about 0.7% for experiments in dynamic condition. We concluded that it is possible to use the developed sensor for measurement of traction force since the maximum output variation of a sensor detecting a traction force was about 0.3% in $0^{\circ}C-60^{\circ}C$ temperature condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.709-716
• /
• 2016

Recently, the operating conditions of the various mechanical structures have become more severe and the running time has become longer as the development of plant equipment increases with the introduction of high technology. Thus, the reliability of the system and its accessories is becoming a problem. Normally, synthetic natural gas (SNG) plants use 1.25Cr-0.5Mo or 2.25Cr-1Mo heat resistant steel according to the operating conditions. In this study, a lab-scale reactor was set up using 1.25Cr-0.5Mo steel, in order to carry out corrosion tests for producing synthetic natural gas. The corrosive characteristics were investigated under 1st-methanator operating conditions and fundamental data about the durability and reliability were obtained by using the experimental test. The analysis of results obtained on the durability of the reactor under emission and injection compositions showed that the hydrogen embrittlement caused by hydrogen and the oxidation corrosion caused by H2O had the most effect on the durability of 1.25Cr-0.5Mo steel in the SNG reactor. However, the hydrogen embrittlement and oxidation corrosion occurred simultaneously under emission conditions, so that the corrosion of the material increased suddenly after a long operating time. Besides, the corrosion of the 1.25Cr-0.5Mo steel under the injection composition was faster than that under the emission composition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.490-497
• /
• 2016

This study compared and analyzed the pollution levels of radiation shielding aprons and ways to sterilize them using 30 lead aprons. After collecting samples from the center of the lead apron, where contact is most frequent, experiments were conducted employing Coagula and Latex methods. Using the culture medium where bacteria grew, measurements of the pathogen count and identification were performed. The greatest number of pathogens were $7.16{\pm}10$, which were detected on the lead apron from general X-ray room #2, but there was no significant difference according to the facilities (p > 0.05). Compared to how many pathogens remained between using the disinfectant ethanol and tissue, the pathogens decreased by $0.01{\pm}0.4$ (p < 0.05) after using disinfectant ethanol and by $0.87{\pm}1.7$(p < 0.05) after using disinfectant tissue. The Pearson correlation test revealed a significant correlation (-0.296, p < 0.05) between them. According to this research, there were pathogens on the lead aprons and the number of pathogens was determined by statistical analysis. It is expected that the rate of radiology technologists, patients, and medical equipment infected by pathogens will be reduced by the proper use of sterilization with a disinfectant ethanol.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1264-1272
• /
• 2015

This study was performed to compare the perceived importance and performance frequency of the core nursing skills between general and special department. Subjects were 182 nurses who work on the hospital. Data was collected using items made by Korean accreditation board of nursing education and analyzed by frequency, mean and t-test. There were differences of importance and frequencies about nursing core skill between general and special wards. Core nursing skills of general wards were higher importance on intradermal injection(p=.011), transfusion(p=.028), simple catheterization(p=.047), cleansing enema(p=<.001), preoperative and postoperative care(p=.035), management administration(p=.027) and oxygenation with cannular(p=.002) than special wards. Actual performance frequency core nursing skills of general wards were higher similar on transfusion(p=.002), intermittent tube feeding(p=.032), simple catheterization(p=<.001), cleansing enema(p=<.001), preoperative care(p=.001), postoperative care(p=<.001), management administration(p=.001), protection equipment for quarantine room and waste disposal(p=.021), oxygenation with cannular(p=<.001) than special wards. It is needed to develop efficient and sequential program to learning the nursing core skills for nursing students.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• Journal of Soil and Groundwater Environment
• /
• v.22 no.6
• /
• pp.112-119
• /
• 2017

In this study, the availability of cow manure as raw material for solid fuel production was investigated. Since the water content of the cow manure was too high, it was dewatered using a laboratory hydraulic compressure ($11.3kg/cm^2$). The moisture content of the cow manure decreased from 82.01% to 73.36 wt.%. The dewatered cow manure was homogenized by the experimental apparatus and then put into the rotating cylindrical apparatus. From the consecutive processes, the cow ball-shaped pellet which size ranged from 3.0 to 25.0 mm was produced. The major factor for making palletized fuel from cow manure was the moisture content. Based on the experimental data, the moisture content of cow manure for pelletizing cow manure was identified as 65~75 wt.%. When the moisture content of the cow manure was lower than 30 wt.%, the diameter of the pellets maded from cow manure was smaller than 3 mm. On the other hand, when the water content of the cow manure was higher than 75 wt/%, the diameter of the processed pellets tended to be larger than 25 mm. The characteristics of the processed cow manure pellets was analyzed to be in accordance with the livestock solid fuel quality standard. The pyrolysis characteristic of the pellet was analyzed by raising the heating temperature of the experimental equipment from 200 to $900^{\circ}C$. The mass change between of 20 and $130^{\circ}C$ corresponds to the amount of moisture contained in the cow manure. The amount of moisture was about 15% of the total weight of cow manure samples. The cow manure pellet was thermally stable up to $280^{\circ}C$. It can be interpreted that combustion of cow manure pellet does not occur until the surface temperature reaches $280^{\circ}C$. The mass change of pellet between of 280 and $450^{\circ}C$ was considered to be due to the vaporization of volatile organic compounds (VOCs) present in the cow manure pellet. The maximum production of VOCs was showed near $330^{\circ}C$.