• 대한치과교정학회지
• /
• 제9권1호
• /
• pp.99-103
• /
• 1979

For the purpose of investigating the response of the periodontal tissue in relation to the experimental tooth movement, the rats were inhibited from collagen formation by adminstration of aminoacetonitrile. Findings were as follows: 1) In experimental group, the principal fibers of the periodontal ligament came to run parallel along the alveolar bone or root surface on the pressure side, while the decrease in density, irregular arrangement, and partial loss of principal fibers were observed on the tension side. 2) Sharpey's fibers at the alveolar bone decreased in number, and as the aminoacetonitrile administration continued, the capability of matrix formation decreased on the tension side, the narrowing of the alveolar septum and poor-bony trabeculation appeared on the pressure side. 3) In cementum, Sharpey's fibers were distributed irregularly. The formation of acellura cementum was decreased on the tension side, while the formative capability of cellular cementum was increased. 4) The degree of staining by Herovici technique decreased in the periodontal membrane. By PAS and ninhydrine -Schiff reaction it was appeared weakly positive in the region where the Sharpey's fibers existed.

• Structural Engineering and Mechanics
• /
• 제9권5호
• /
• pp.505-518
• /
• 2000

A major cause of premature debonding of tension face plates is shear peeling (Jones et al. 1988, Swamy et al. 1989, Ziraba et al. 1994, Zhang et al. 1995), that is debonding at the plate ends that is associated with the formation of shear diagonal cracks that are caused by the action of vertical shear forces. It is shown in this paper how side plated beams are less prone to shear peeling than tension face plated beams, as the side plate automatically increases the resistance of the reinforced concrete beam to shear peeling. Tests are used to determine the increase in the shear peeling resistance that the side plates provide, and also the effect of vertical shear forces on the pure flexural peeling strength that was determined in the companion paper. Design rules are then developed to prevent premature debonding of the plate ends due to peeling and they are applied to the strengthening and stiffening of continuous reinforced concrete beams. It is shown how these design rules for side plated beams can be adapted to allow for propped and unpropped construction and the time effects of creep and shrinkage, and how side plates can be used in conjunction with tension face plates.

• 해양환경안전학회지
• /
• 제4권2호
• /
• pp.63-68
• /
• 1998

This study is aimed to predict the configuration and tension of a towing cable of a side-scan sonar which plays an important role in developing ocean resources. The governing equations of 3-D static equilibrium equations for a flexible cable are derived and solved using a finite difference method. The forces considered in this paper are effective weights, drag forces due to currents and ship moving, and the tension at both ends of the towing cable. The governing equations are non-linear, so an iteration method is applied to solve the equation. A case study is carried out for several different conditions. The result will be useful for predicting the location of a side-scan sonar and to design the towing system.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.55-60
• /
• 2004

In this study, the configuration and tension of a towing cable for side-scan sonar are predicted in an ambient flow and at an unsteady towing condition. The governing equation of three-dimensional dynamic analysis for a flexible cable is solved using a finite difference method. We successfully predict the configuration and tension of a side-scan sonar and designed the towing system. It is found in static analyses that the side-scan sonar must be towed to keep a its stable depth at a reasonable speed. The study also reveals in the transient analyses that the dominant component affecting the top tension is the tangential drag force for the larger towing speed than the critical speed, and the self weight of a towed instrument for the smaller towing speed than. It should be maneuvered for a towing vessel with good consideration for the impact effect in a cable due to tension peak when a towing speed is suddenly increase. The developed program can be applicable for three-dimensional dynamic analysis of a towing system for various marine survey instruments.

• 한국해양학회지:바다
• /
• 제8권2호
• /
• pp.203-209
• /
• 2003

본 연구에서는 해양탐사장비를 예인하는 예인케이블에 관한 3차원 동적해석을 수행하였다. 해양케이블에 관한 지배방정식 중에서 굽힘강성 성분도 포함되는 보다 일반적인 지배방정식을 사용하였으며, 지배방정식은 3차원 비선형, 연성방정식이다. 예인선박의 예인속도와 측면주사음탐기의 중량에 따라서 예인단에서 발생하는 장력을 추정하였으며, 임의의 시간에 대한 케이블의 전체형상을 추정하였다. 정적해석결과를 통하여 특정한 수심에서 해양탐사장비를 예인할 때 예인속도를 잘못 조절한다면 관측장비가 해저면 바닥에 닿아서 탐사장비를 손실할 수 있다는 것을 알 수 있었다. 다양한 예인속도에 따른 예인단에서 장력의 변화를 살펴보았는데, 이를 통하여 예인단 장력은 예인속도가 임계속도보다 클 때는 접선하중성분이 지배적이고 작을 때는 자중효과가 지배적으로 나타난다는 것을 알 수 있었다. 또한 속도가 변하는 천이영역에서는 장력의 피크가 나타났으며 이것은 케이블에 충격력 효과로 작용할 수 있으므로 예인선박 운용에 이를 잘 고려해야 할 것이다. 본 연구결과는 다양한 해양탐사장비의 예인문제에 적용할 수 있을 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.900-905
• /
• 2004

Development of color printer, postal classification machine, ATM and so on requires higher moving performance of the flat belt. Skew of the flat belt running over misaligned roller has a bad effect on performances of media transport. The vibration of loose side of belt causes the escape of the belt from roller and the drop of velocity of driven roller after the start of driving roller revolution. The skew of flat belt is investigated by FEM and dynamic simulation. FEM results show parameters which affect the skew of belt and match with dynamic results qualitatively. The shape of loose side of belt can be found by dynamic simulation. Increase of the acceleration time and initial tension have diminished the unstable movement of the loose side of belt.

• 한국가구학회지
• /
• 제11권2호
• /
• pp.7-12
• /
• 2000

This paper describes the bending strength properties of laminated woods which had three kinds of specimens according to finger length-12, 4.5 mm and butt joint and the acoustic emissions (AEs) generated during the test. 3-ply laminated wood beams were tension side layers (lower layers) composed of one middle lamina and two side-jointed laminae, with one butt joint ($_1BJ$), one finger joint (12mm, $_1FJ_{12}$) or one finger joint (4.5mm, $_1FJ_{4.5}$) in the middle lamina of tension side layer. And 3-ply laminated wood beams were tension side layers (lower layers) also composed of one lamina, with one butt joint (BJ), one finger joint (12mm, $FJ_{12}$) or one finger joint (4.5mm, $FJ_{4.5}$/) in tension side layer. Cryptomelia pieces were cut for butt and two finger types and glued with resorcinol-phenol resin adhesive. The results were as follows It was not effective in the bending modulus of elasicity (MOE) with IFJL type and had no difference from finger length. The bending modulus of rupture (MOR) of laminated wood beams including finger joint was the same values as that including butt feint and had no difference from finger length. It was effective in MOE with FJL type and had no difference from finger length. The effect of finger joint on MOR was much higher than that of butt joint but had no difference from finger length. The AE generation time of IFJL type was earlier than that of the control wood and the number of AE count was much more than that of the control wood. However, the AE generation time of FJL type was earlier than that of the control wood and the number of U count was much fewer than that of the control wood.

• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.63-69
• /
• 1992

본 연구에서는 특히 앞서 지적한 표면균열의 진전거동에 관한 연구와도 관련 하여 측면홈을 가진 중앙관통균열(side-grooved center cracked tension) 시험편에 대 해 피로균열 진전실험을 수행하고, 평면변형률 조건의 만족여부 및 응력강도계수 평가 방법에 관하여 검토하여 비교적 새로운 결과를 얻었으므로 여기에 보고하고자 한다.

• 대한치과교정학회지
• /
• 제23권1호
• /
• pp.89-100
• /
• 1993

The purpose of this study was to evaluate the effect of orthodontic force on periodontal cellular activity by immunoperoxidase stain of epidermal growth factor, one of the tissue hormone. And supplementarily, to investigate of the changes of periodontal structures, periodontium was stained by H-E, Masson's Trichrome, P. A. S. stain after orthodontic force application. The experimental animals were four young adult dogs of average 8 month old. The fixed orthodontic appliance was cemented on mandibular right 4th premolar and 1st molar of each animal as experimental site. Mandibular left 4th premolar area of the same animal was used as control. The appliance consist of two silver crown soldered with 0.030' tube, $0.018\times0.022'$ S.S. sectional arch wire, and 0.009' open coil spring for manifestating of orthodontic force for bodily tooth movement of mandibular 4th premolar toward mesial direction. Experimental group was sacrificed at 1, 2, 3, 5 weeks from beginning of the experiment, and was investigated immunohistochemically and bistochemically by several staining methods. Findings were as follows: 1. The degree of EGF staining in control group was highest in epithelium of periodontium, and osteoclasts, osteoblasts and fibroblasts around the capillary were stained at higher level in periodontium. Generally, control group shows positive distribution of EGF all around the periodontal area. 2. The degree of EGF staining in control and 5 week group were similar, and did not show the significant different level between tension and pressure side. 3. All of 1, 2, 3 week group showed the same staining degree and distribution of EGF, and the tension side was more positive reaction of EGF stain than the pressure side. 4. The features of collagen fiber and periodontal fiber arrangement observed by H-E, Masson's Trichrome and P. A. S. stain revealed that oblique periodontal fibers were strectched in tension side, compressed in pressure side of all experimental group. Some fiber group in pressure side of 5 week group recovered the regular arrangement along the capillaries.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2752-2761
• /
• 1993

The purpose of this study is to confirm the decreasing problems of residual bending strength, and the fracture machanism experimentally when CFRP composite laminates are subjected to Foreign Object Damage. Composite laminates used for this experiment are CFRP orthotropy laminated plates, which have two-interfaces [O/sub 6//sup o//90/sub 6//sup o/]sub sym/ and four-interfaces [O/sub 3//sup o//90/sub 6//sup o//O/sub 3//sup o]/sub sym/. When the specimen is subjected to transverse impact by a steel ball, the delamination area generated by impact damage is observed by using SAM(Scanning Acoustic Microscope). also, Thefracture surfaces obtained by three-point bending test were observed by using SEM (Scanning Electron Microscope). Then, fracture mechanism was investigated based on the observed delamination area and fracture surface. The results were summarized as follows; (1) It is found that for the specimen with more interface, the critical delamination energy is increased while delamination-development energy is decreased. (2) Residual bending strength of specimen A is greater than that of Specimen B within the impact range of impact energy 1. 65J (impacted-side compression) and 1. 45J (impacted-side tension). On the other hand, when the impact energy is beyond the above ranges, residual bending strength of specimen A is smaller than that of specimen B. (3) In specimen A and B, residual strength of CFRP plates subjected to impact damage is lower in the impacted-side compression than in the impacted-side tension. (4) In the case of impacted-side compression, fracture is propagated from the transverse crack generat-ed near impact point. On the other hand, fracture is developed toward the impact point from the edge of interface-B delamination in the case of impacted-side tension.