• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1269-1279
• /
• 2023

Pool boiling experiments are performed within an isolated bubble regime at inclination angles of 0° and 45°. When a bubble grows and departs from the heating surface, the pressure, buoyancy, and surface tension force play important roles. The curvature and base diameter are required to calculate the pressure force, the bubble volume is required to calculate the buoyancy force, and the contact angle and base diameter are required to calculate the surface tension force. The contact angle, base diameter, and volume of the bubbles are evaluated using images captured via a high-speed camera. The surface tension force equation proposed by Fritz is modified with the contact angles obtained in this study. When the bubble grows, the contact angle decreases slowly. However, when the bubble departs, the contact angle rapidly increases owing to necking. At an inclination angle of 0°, the contact angle is calculated as 82.88° at departure. Additionally, the advancing and receding contact angles are calculated as 70.25° and 82.28° at departure, respectively, at an inclination angle of 45°. The dynamic behaviors of bubble growth and departure are discussed with forces by pressure, buoyancy, and surface tension.

• Textile Coloration and Finishing
• /
• v.20 no.3
• /
• pp.1-7
• /
• 2008

Three kinds of 135D/108F ITY were produced from raw yam 85D/72F + SDY 50D/36F with. interlacing pressure $1.5kg/cm^2$, $2.5kg/cm^2$, $3.5kg/cm^2$ respectively. 72 kinds of sized yams were manufactured from three ITYs by altering sizing speed, sizing temperature and sizing tension. The mechanical characteristics of 72 kinds of plain fabrics which were woven using the sized yam as a warp were analyzed after scouring. The initial modulus of scoured fabric responded sensitively to the sizing speed in high tension. The WT of scoured fabric recorded the. highest1n the conditions of sizing tension 30g, and air pressure $2.5kg/cm^2$ in interlacing treatment. When sizing temperature was high, the WT value appeared low, but when sizing speed was high, the WT value was much affected by air pressure in interlacing raw yam. The MIU value of fabric according to sizing tension variations increased up to sizing tension 40g, but decreased above it. The bulk density decreased up to sizing tension 30-40g, but increased above it. In addition, the bulk density decreased as sizing temperature increased.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.101-114
• /
• 1996

Even though the Coulomb's earth pressure theory has been mainly used in practice, the general equation does not exist yet, which is applicable to retaining wall backfilled by cohesive soils. Here, for gravity walls backfilled by cohesive soils, some equations have been derived by newly using the Coulomb's theory, for the cases oi drained and untrained analyses. and for the cases of neglecting and considering the tension crack, respectively. Both the active earth thrust and the depth of tension crack under different conditions were tabulated.

• The Journal of Korean Physical Therapy
• /
• v.14 no.1
• /
• pp.117-124
• /
• 2002

Poor posture of the neck and head long been recognized as a factor contributing to the onset and perpetuation of pain in the head and neck region. The purposes of the study were to evaluate the changes in forward head posture and pressure pain threshold in tension type headache group and control group. Forward head posture were measured to craniovertebral angle and cranial rotation angle. Craniovertebral angle was smaller in tension type headache group(p<0.05), and cranial rotation angle was larger in tension type headache group(p<0.05). Pressure pain threshold was similar between tension type headache group and control group with the exception of right suboccipitalis and left temporalis(p<0.05).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.101-101
• /
• 2008

The effect of oxygen partial pressure on the surface tension data of liquid alloys was investigated by means of comparing the calculated data and the measured one. Two binary alloy systems were chosen to observe the dependence of oxygen adsorption behavior on different oxygen partial pressures. It was found that the difference between the computed values and the experimental of the surface tension was within the range of maximum 10%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.5
• /
• pp.570-575
• /
• 2011

Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper analyzed Cu sheet deposition characteristics using ultrasonic metal welder and tension tester. A horn suitable for 40,000Hz was attached to the ultrasonic metal welder in order to weld Cu plates. The Cu sheet welding was done with different amplitude, pressure, and welding time, and its maximum tension was measured with tension tester. Maximum tension of 153.87N was obtained when the pressure was 2.0bar, amplitude was 80%, and welding time was 0.30s. Therefore, excessive welding condition negatively influences maximum tension measurement result.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.311-317
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the thinner width ring can bring not only the friction reduction between the ring and liner during engine running, but also the adjustment of the blow-by gas and oil consumption by changing in the pressure in the crevice volume and the axial motion of rings togethe with the adjustment of the inter-ring crevice volumes. In this study, by using a developed basic computer proglram that predicts the blow-by gas and oil consumption of engines, it is to be examined how satisfying the level of the blow-by gas and oil consumption as being installed the piston ring pack with thinner width ring and lower tension ring.

• Nuclear Engineering and Technology
• /
• v.41 no.7
• /
• pp.979-988
• /
• 2009

Tensioned metastable fluids provide a powerful means for low-cost, efficient detection of a wide range of nuclear particles with spectroscopic capabilities. Past work in this field has relied on one-component liquids. Pure liquids may provide very good detection capability in some aspects, such as low thresholds or large radiation interaction cross sections, but it is rare to find a liquid that is a perfect candidate on both counts. It was hypothesized that liquid mixtures could offer optimal benefits and present more options for advancement. However, not much is known about radiation-induced thermal-hydraulics involving destabilization of mixtures of tensioned metastable fluids. This paper presents results of experiments that assess key thermophysical properties of liquid mixtures governing fast neutron radiation-induced cavitation in liquid mixtures. Experiments were conducted by placing liquid mixtures of various proportions in tension metastable states using Purdue's centrifugally-tensioned metastable fluid detector (CTMFD) apparatus. Liquids chosen for this study covered a good representation of both thermal and fast neutron interaction cross sections, a range of cavitation onset thresholds and a range of thermophysical properties. Experiments were devised to measure the effective liquid mixture viscosity and surface tension. Neutron-induced tension metastability thresholds were found to vary non-linearly with mixture concentration; these thresholds varied linearly with surface tension and inversely with mixture vapor pressure (on a semi-log scale), and no visible trend with mixture viscosity nor with latent heat of vaporization.

• Nuclear Engineering and Technology
• /
• v.36 no.6
• /
• pp.512-527
• /
• 2004

This paper describes the finite element (FE) analysis results of a 1/4 scale model of a prestressed concrete containment vessel (PCCV) by considering the tension stiffening effect, which is a result of the bond effect between the concrete and the steel. The tension stiffening model is assumed to be an exponential form based on the relationship between the average stress and the average strain of the concrete. The objective of the present FE analysis is to evaluate the ultimate internal pressure capacity of the PCCV, as well as its failure mechanism, when the PCCV model is subjected to a monotonous internal pressure beyond is design pressure capacity. With the commercial code ABAQUS, the FE analysis used two concrete failure criteria: a 2-dimensional axi-symmetric model with modified Drucker-Prager failure criteria and a 3-dimensional model with a damaged plasticity mod디. The results of our FE analysis on the ultimate pressure capacity and failure modes of PCCV have a good agreement with the experimental data.

• Journal of Chest Surgery
• /
• v.22 no.6
• /
• pp.894-900
• /
• 1989

It has been suggested that mixed venous $O_{2}$ tension is a predicor of cardiac output especially in a critically ill patient after an open heart surgery. From April 1988 through September 1989, we monitored mixed venous $O_{2}$ tension and pulmonary arterial pressure in 48 patients with acyanotic congenital heart disease at postoperative 1 hour, 6 hour, 12 hour, 24 hour, and 48 hour respectively. They were divided into Group I, with severe pulmoary hypertension, and Group II, without severe pulmonary hypertension. In Group I, mixed venous $O_{2}$ tension and cardiac index showed significant increase with time (p<0.05), but the ratio of pulmonary-aortic systolic pressure didn't show significant change. The increase was significant only 24 hour after operation, and so this low cardiac performance in early postoperative period should be considered when postoperative management is being planned in the risky patient. In Group II, all of the three variables didn't show any significant change with time. The correlation coefficient between mixed venous $O_{2}$ tension and cardiac index was significantly different from zero in both Group I (p<0.001) and group II (p<0.05) at each imeperiod, but the ratio of pulmonary-aortic systolic pressure didn't correlated well with the other 2 variables. Our study showed that serial determination of mixed venous $O_{2}$ tension in acyanotic congenital heart disease could be used as a guide in estimating the cardiac index postoperatively.