• 패션비즈니스
• /
• 제23권1호
• /
• pp.37-48
• /
• 2019

WKSF (Warp-knitted spacer fabrics) knitted using a double Raschel machine is the three-dimensional knit that has vertically connected separate layers in loop structures. Because of its unique structure, the fabric is light, compressible and breathable. Owing to the high production speed, the use of the fabric is increasing in various areas. The purpose of this study is to establish the design process in the utilization of WKSF program and analyze the difference between WKSF and Neoprene as garment materials.. The study on the design related to WKSF has rarely been carried out because of the complexity of WKSF structure and the difficulties encountered in analyzing the structure and thread. Therefore, checking beforehand the simulation results similar to a final knit using the CAD program for WKSF can only enhance the efficiency of the design for the light knits. The conclusion drawn after designing the light knits using the CAD program and analyzing the pros and cons of WKSF through the various property evaluation techniques is as follows. The tension characteristic analysis results indicated that Neoprene specimen has the elastic transformation and resilience, thus behaving like an elastic product such as rubber. By contrast, in the event that clothing and fashion accessories are designed with WKSF, these products are kept in a boxy style fit so that the fabric can be applied flexibly to a curvy body line. In addition, WKSF is good in forming noticeably around a curvy body, because its resistance shear deformation is lower than that of Neoprene.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권3호
• /
• pp.75-82
• /
• 2019

아스팔트 콘크리트(AC) 궤도는 열차 하중에 의한 궤도 하부노반의 발생응력을 최소화하고, 적외선에 민감한 AC의 노출면적을 감소시켜 온도 영향에 따른 AC 도상의 소성변형을 줄일 수 있는 슬래브 패널 개발이 매우 중요하다. 본 연구에서는 형상 설계 및 실내성능시험을 통해 AC 궤도용 슬래브 패널을 개발하였으며, KRL-2012 표준열차하중 모델 및 KR-C코드에 의한 다양한 정적 하중조합에 따른 슬래브 패널에 작용하는 휨 인장응력 및 설계모멘트를 유한요소해석을 통해 구조 안전성을 검토하였다. 또한 AC 궤도용 슬래브 패널의 설계 적합성을 검증하기 위하여, EN 13230-2에 의거 슬래브 패널 주요 위치별로 정적 휨 강도 시험, 동적 휨 강도 시험을 수행하였다. 성능 시험 결과, AC 궤도용 슬래브 패널은 균열 하중 및 균열 확대 여부 등 유럽 표준에서 요구되는 성능 기준을 모두 만족하였다.

• 한국재료학회지
• /
• 제29권6호
• /
• pp.392-397
• /
• 2019

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061 three-layer clad sheet. Two AA6061 and one AA5052 sheets of 2 mm thickness, 40 mm width, and 300 mm length are stacked, with the AA5052 sheet located in the center. After surface treatment such as degreasing and wire brushing, sample is reduced to a thickness of 1.5 mm by multi-pass cold rolling. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at rolling speed of 6.0 m/sec. The roll bonded AA6061/AA5052/AA6061 complex sheet is then hardened by natural aging(T4) and artificial aging(T6) treatments. The microstructures of the as-roll bonded and age-hardened Al complex sheets are revealed by optical microscopy; the mechanical properties are investigated by tensile testing and hardness testing. After rolling, the roll-bonded AA6061/AA5052/AA6061 sheets show a typical deformation structure in which grains are elongated in the rolling direction. However, after T4 and T6 aging treatment, there is a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 sheets. The as roll-bonded specimen shows a sandwich structure in which an AA5052 sheet is inserted into two AA6061 sheets with higher hardness. However, after T4 and T6 aging treatment, there is a different sandwich structure in which the hardness of the upper and lower layers of the AA6061 sheets is higher than that of the center of the AA5052 sheet. The strength values of the T4 and T6 age-treated specimens are found to increase by 1.3 and 1.4 times, respectively, compared to that value of the starting material.

• 한국융합학회논문지
• /
• 제10권8호
• /
• pp.153-158
• /
• 2019

현대사회에 이르며 발생한 환경오염으로 인해 산업 전반적인 환경규제가 강화되었다. 따라서 이러한 환경규제를 충족하기 위해 선택적 환원촉매장치(SCR)의 연구개발이 필요하다. 본 논문은 SCR 시스템의 핵심부품인 공압식 댐퍼 밸브(PDV)를 개발하기 위하여 열해석을 수행하였다. 열해석을 위해 우선적으로 재질의 물성치 검증을 실시하였다. 검증은 시편의 열물성시험과 열인장시험을 통해 하였으며 결과를 재질의 물성치에 보강하여 열해석의 신뢰성을 높이도록 하였다. 열해석은 유한 요소 프로그램(Ansys)를 사용하여 PDV가 갖는 사용 조건에 따라 적용된 총 3개 재질(SM400B, SS275, SB410)에서의 PDV가 보이는 열 특성을 확인하고자 하였으며, 이를 통해 PDV가 갖는 구조적 안정성을 확인하고자 하였다.

• Geomechanics and Engineering
• /
• 제17권1호
• /
• pp.57-67
• /
• 2019

Water-induced strength reduction is one of the most critical causes for rock deformation and failure. Understanding the effects of water on the strength, toughness and deformability of rocks are of a great importance in rock fracture mechanics and design of structures in rock. However, only a few studies have been conducted to understand the effects of water on fracture properties such as fracture toughness, crack propagation velocity, consumed energy, and microstructural damage. Thus, in this study, we focused on the understanding of how microscale damages induced by water saturation affect mesoscale mechanical and fracture properties compared with oven dried specimens along three notch orientations-divider, arrester, and short transverse. The mechanical properties of calcite-cemented sandstone were examined using standard uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) tests. In addition, fracture properties such as fracture toughness, consumed energy and crack propagation velocity were examined with cracked chevron notched Brazilian disk (CCNBD) tests. Digital Image Correlation (DIC), a non-contact optical measurement technique, was used for both strain and crack propagation velocity measurements along the bedding plane orientations. Finally, environmental scanning electron microscope (ESEM) was employed to investigate the microstructural damages produced in calcite-cemented sandstone specimens before and after CCNBD tests. As results, both mechanical and fracture properties reduced significantly when specimens were saturated. The effects of water on fracture properties (fracture toughness and consumed energy) were predominant in divider specimens when compared with arrester and short transverse specimens. Whereas crack propagation velocity was faster in short transverse and slower in arrester, and intermediate in divider specimens. Based on ESEM data, water in the calcite-cemented sandstone induced microstructural damages (microcracks and voids) and increased the strength disparity between cement/matrix and rock forming mineral grains, which in turn reduced the crack propagation resistance of the rock, leading to lower both consumed energy and fracture toughness ($K_{IC}$).

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1210-1218
• /
• 2018

A new type of earthquake-resisting element that consists of a steel plate shear wall with slits is introduced. The infill steel plate is divided into a series of vertical flexural links with vertical links. The steel plate shear walls absorb energy by means of in-plane bending deformation of the flexural links and the energy dissipation capacity of the plastic hinges formed at both ends of the flexural links when under lateral loads. In this paper, finite element analysis and experimental studies at low cyclic loadings were conducted on specimens with steel plate shear walls with multilayer slits. The effects caused by varied slit pattern in terms of slit design parameters on lateral stiffness, ultimate bearing capacity and hysteretic behavior of the shear walls were analyzed. Results showed that the failure mode of steel plate shear walls with a single-layer slit was more likely to be out-of-plane buckling of the flexural links. As a result, the lateral stiffness and the ultimate bearing capacity were relatively lower when the precondition of the total height of the vertical slits remained the same. Differently, the failure mode of steel plate shear walls with multilayer slits was prone to global buckling of the infill steel plates; more obvious tensile fields provided evidence to the fact of higher lateral stiffness and excellent ultimate bearing capacity. It was also concluded that multilayer specimens exhibited better energy dissipation capacity compared with single-layer plate shear walls.

• 한국산학기술학회논문지
• /
• 제22권1호
• /
• pp.37-44
• /
• 2021

수소연료전지차(FCEV)는 전기를 자체 생산하는 연료전지를 동력원으로 하고 있으며 기존 기계식 레귤레이터의 출구압은 시스템 사양에 의해 제작 시점에서 고정되며 순간적인 수소 공급량에 의한 출구압 강하가 발생하는 경우 수소의 공급유량이 부정확해지는 문제가 있다. 본 연구에서는 기존에 존재하는 1단 기계식 감압 레귤레이터를 보완하기 위한 2단 감압 레귤레이터의 형상 설계 및 재질 선정을 수행하였다. 2단계 감압을 통한 맥동과 느린 응답을 보상하고 고압 편차 문제를 해결하기 위해 감압 유닛의 접촉면 형상을 가공성을 고려하여 설계하였다. 기밀성 측면에서 TPU의 변형량은 최대 15.82% 작은 변위량을 보였으며, 재질 선정에서는 2단 감압에 보편성을 확보하고 다양한 수소 연료 공급시스템에 적용 가능한 전자식 솔레노이드를 고려하여 자성체를 선정하고 적절한 도금 종류를 검증하기 위한 수소 취성 및 내식성 평가를 실시하였다. 시편의 표면 부식은 Cr 도금의 경우에서만 발생되지 않았으며, 인장 시험을 통해 부식과정간 연신율을 비교하였을 때, 2% 이내의 차이를 확인하였다.

• 한국항공우주학회지
• /
• 제49권3호
• /
• pp.205-212
• /
• 2021

본 연구에서는 플렉셔를 적용한 추력 시험대 설계를 위해 두 가지 유형에 따른 추력 시험대 모델링을 제시하였다. Type A의 모델은 접선 하중(추력)과 지면에 대한 축 방향 하중(자중)이 압축하중으로 발생되고, Type B의 모델은 축 방향 하중이 인장하중으로 발생되도록 설계를 하였다. 두 가지 유형에 대해 하중에 따른 영향성을 확인하였고, 1D 계산 결과와 전산해석 결과에 대해 비교를 수행하였다. 거리 비(x/L)에 대해 총 10구간을 1D 계산 값과 전산해석 값을 비교하였고 그 결과는 매우 유사한 것을 확인할 수 있었다. 해석 결과에 대한 타당성을 입증하기 위해 플렉셔에 대한 전산해석으로부터 등가응력(Equivalent Stress)을 확인하였고, 항복조건(Von-Mises Yield Criterion) 평가로부터 Type B 모델의 제작을 선정하였다.

• Earthquakes and Structures
• /
• 제20권1호
• /
• pp.109-122
• /
• 2021

Significant progress in the oil and gas industry advances the application of pipeline into an intelligent era, which poses rigorous requirements on pipeline safety, reliability, and maintainability, especially when crossing seismic zones. In general, strike-slip faults are prone to induce large deformation leading to local buckling and global rupture eventually. To evaluate the performance and safety of pipelines in this situation, numerical simulations are proved to be a relatively accurate and reliable technique based on the built-in physical models and advanced grid technology. However, the computational cost is prohibitive, so one has to wait for a long time to attain a calculation result for complex large-scale pipelines. In this manuscript, an efficient and accurate surrogate model based on machine learning is proposed for strain demand prediction of buried X80 pipelines subjected to strike-slip faults. Specifically, the support vector regression model serves as a surrogate model to learn the high-dimensional nonlinear relationship which maps multiple input variables, including pipe geometries, internal pressures, and strike-slip displacements, to output variables (namely tensile strains and compressive strains). The effectiveness and efficiency of the proposed method are validated by numerical studies considering different effects caused by structural sizes, internal pressure, and strike-slip movements.

• 대한금속재료학회지
• /
• 제46권6호
• /
• pp.329-337
• /
• 2008

During the continuous casting of boron-bearing steel, the corner cracks on the slab are formed by deformation with low strain rate and rapid cooling at the unbending temperature within the range of 800- $1000^{\circ}C$. Especially, the rapid cooling in the corner of slab during the continuous casting leads to as corner cracking. Therefore, in this study, the hot tensile tests applied to the different cooling rates were taken into account in order to study the effect of cooling rate on the hot ductility of boron-bearing steel. The results revealed that increasing cooling rate deteriorate the hot ductility of boron- bearing steel. Rapid decreasing of the hot ductility is caused by formation of a film-like ferrite and precipitate at the austenite grain boundaries. The morphology of the precipitates in the boron-bearing steel was monitored by PTA (Particle Tracking Autoradiography) and TEM, we observed MnS and BN compound and their morphology was quite different depending on the cooling rates. When the cooling rate is increased, rodshape MnS and BN precipitates can be formed along the austenite grain boundaries. It can cause that weakening the boundary region and decreasing the hot ductility of boron-bearing steel.