• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.68-74
• /
• 2015

In the present work, a series of numerical calculations have been conducted on the cooling of a hot surface using an air/water mist jet. In some cooling processes, such as in the glass-tempering process, direct contact between the cold water drops and the hot surface should be avoided, because this may cause surface cracks due to the sharp temperature gradients. Thus, the main focus of this study is finding the appropriate operating conditions for maximum cooling without direct contact between the drops and the surface. A series of numerical experiments have been performed, and, at the same time, those results were compared with those of the previous experiments for verification purposes. The effects of droplet impinging velocity, hot plate temperature, and liquid loading ratio for mono-dispersed drops of various sizes were studied in detail.

• Journal of the Korean Wood Science and Technology
• /
• 제23권3호
• /
• pp.28-32
• /
• 1995

The presteamed or prefrozen persimmon blocks of 10cm ${\times}$ 10cm ${\times}$ 15cm were air-dried at room temperature until about 30% moisture content, and then were dried in a MW oven. During drying their internal temperatures were monitored with thermo-couple probes. The presteamed and prefrozen blocks didn't show any improvement in drying rate and moisture gradient when compared with the controls. Checks appeared on the surfaces of most presteamed blocks during air-drying. It has been clearly revealed that the maximum weight, loss must, be less than 2g/min during MW drying to prevent internal checking and that MW drying reduced moisture gradients inside blocks. MW dried the persimmon blocks 440 times faster than conventional kiln.

• The Korean Journal of Ecology
• /
• 제6권3호
• /
• pp.153-166
• /
• 1983

The distribution of beech species (Fagus) and beech-dominated forests along climatic gradients in the Northern Hemisphere was studied by use of taxonomic and ecological literature. The genus Fagus as a whole occurs over the range of 4.5 to 20.0。C mean annual temperature and 600 to 1000 mm in lower limit, mean annual precipitation. At the higher end of the temperature range, beech occurs in zones with relatively high growing-season precipitation. Edaphically, beech species and beech-dominated forests tend to occur on mesic, moderately fertile sites. Beech-dominated forests occur in a limited portion of the climatic range of the genus with sensitive responses to other environmental factors. The distributional range of beech-dominated forests on a global scale depends more on climatic factors and geological events than on soil conditions or other factors, summarizing the facts obtained by many researchers on beech dominated forests.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.37-44
• /
• 2000

Numerical investigation is made to study the effects of natural convection on the formation of macrosegregation of a Pb-Sn alloy solidification process in a 2-D confined rectangle mold. The governing equations are calculated using previous continuum models with SIMPLE algorithm doring the solidification process. In addition. to track the solid-liquid interface with time variations. the moving boundary condition Is adopted and irregular interface shapes are treated with Boundary-Fitted Coordinate system. As the temperature reduce from the liquidus to the solidus, the liquid concentration of Sn. the lighter constituent, increases. Then the buoyancy-driven flow due to temperature and liquid composition gradients, called thermosolutal convection or double diffusion, occurs in the mushy region and forms the complicated macrosegregation maps. Related to this phnomena, effects on the macrosegregation formation depending on the cooling condition and gravity values are described.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.215-217
• /
• 2004

In order to obtain the initial starting sample having a random texture and fine grains, aluminum alloy 3103 sheets were repeatedly deformed by CCSS up to six passages and subsequently annealed at $300^{\circ}C$ for 1h. These samples were cold rolled at room temperature and also warm rolled at $250^{\circ}C$. Changes in rolling temperature gave rise to the different texture evolution. Warm rolling led to the pronounced texture gradients comprising the shear texture at the surface and the rolling texture at the sheet center. The formation of the rolling texture components, i.e., the ${\beta}$-fiber, was promoted by cold rolling than warm rolling.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1337-1345
• /
• 2001

Numerical investigation is made to study the effects of thermosolutal convection on the formation of macrosegregation in a Pb-Sn alloy solidification process in a two dimensional confined rectangluar mold. The basic equations are sovled using the Contrinum Model theory with the SIMPE algorithm during the solidification process. In addition, to track the liquid-solid interface with time variations, the moving boundary condition was adopted and moving irregular interface shapes were treated with the time-dependent, boundary-fitted coordinate system. As the temperature reduces from the liquidus to the solidus, the liquid concentration of Sn, the lighter constituent, increases. Then the buoyancy-driven flow due to temperature and liquid composition gradients occurs in the mushy region and forms the complicated macrosegregation maps. belated to this phenomena, effects on the macrosegregation formation depending on the cooling condition and gravity values are examined.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.50-60
• /
• 1996

We designed and developed the burner which would be adapted on the burner type diesel particulate trap system. The burner type particulate trap system consists of burner system to regenerate to ceramic filter, ceramic filter canister, system controller and etc. Many design factors which affect the performance of the burner system were discussed. We also investigated burner characteristics according to the operating parameters. Burned gas temperature could be controlled better by the 2nd air flow rate than the 1st one. As the space velocity increases, the axial and radial temperature gradients in the filter decreases.

• Structural Engineering and Mechanics
• /
• 제75권6호
• /
• pp.659-674
• /
• 2020

The present paper employs nonlocal strain gradient theory (NSGT) to study buckling behavior of functionally graded magneto-electro-thermo-elastic (FG-METE) nanoshells under various physical fields. NSGT modeling of the nanoshell contains two size parameters, one related to nonlocal stress field and another related to strain gradients. It is considered that mechanical, thermal, electrical and magnetic loads are exerted to the nanoshell. Temperature field has uniform and linear variation in nanoshell thickness. According to a power-law function, piezo-magnetic, thermal and mechanical properties of the nanoshell are considered to be graded in thickness direction. Five coupled governing equations have been obtained by using Hamilton's principle and then solved implementing Galerkin's method. Influences of temperature field, electric voltage, magnetic potential, nonlocality, strain gradient parameter and FG material exponent on buckling loads of the FG-METE nanoshell have been studied in detail.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.212-222
• /
• 1994

In the annular Modified Chemical Vapor Deposition process using two concentric tubes, the inner tube is heated to maintain high temperature gradients to have high thermophoretic force which can increase particle deposition efficiency. However, higher axial velocity in a narrow gap between inner and outer tubes can result in a longer tapered entry length. In the present paper, a new concept using an annular jet from the inner tube is presented and shown to significantly reduce the tapered entry length with maintaining high efficiency. Effects of a jet injection on heat transfer, fluid flow and particle deposition have been studied. Of particular interests are the effects of jet velocity, jet location and temperature on the deposition efficiency and tapered length . Torch heating effects from both the previous and present passes are included and the effect of surface radiation between inner and outer tubes is also considered.

• 오토저널
• /
• 제8권1호
• /
• pp.62-74
• /
• 1986

The simulation of power cycle and unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 2-stroke cycle compression ignition engine was studied in this paper. In power cycle process, the single-zone model proposed by Whitehouse and Way was used, and the convective and radiative heat transfer from cylinder contents to surroundings was considered. To solve the equations for gas exchange process, the generalized method of characteristics including area change, friction, heat transfer and entropy gradients was used. Also with the path line calculation, the entropy change along the path line and the variation of specific heat due to the change of temperature and the composition of cylinder gas were considered. As a result of the simulation, the change of pressure and temperature in the cylinder against the crank angle, the rate of net heat release, and the change of properties at each point in the inlet and exhaust pipe against the crank angle were obtained. The engine performances under various operating conditions were also calculated.