• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.2
• /
• pp.156-172
• /
• 2014

This research measures and compares on-site net radiation energy, air temperature, wind speed, and surface temperature considering various spatial characteristics with a focus on land use types in urban areas in Changwon, Southern Gyeongsangnam-do, to analyze the accuracy of an ENVI-met model, which is an analysis program of microclimate. The on-site measurement was performed for three days in a mobile measurement: two days during the daytime and one day during the nighttime. The analysis using the ENVI-met model was also performed in the same time zone as the on-site measurement. The results indicated that the ENVI-met model showed higher net radiation than the on-site measurement by approximately $300Wm^{-2}$ during the daytime whereas the latter showed higher net radiation energy by approximately $200Wm^{-2}$ during the nighttime. The temperature was found to be much higher by approximately $2-6^{\circ}C$ in the on-site measurement during both the daytime and nighttime. The on-site measurement also showed higher surface temperature than the ENVI-met by approximately $7-13^{\circ}C$. In terms of the wind speed, there was a significant difference between the results of the ENVI-met model and on-site measurement. As for the correlation between the results of the ENVI-met model and on-site measurement, the temperature showed significantly high correlation whereas the correlations for the net radiation energy, surface temperature, and wind speed were very low. These results appear to be affected by excessive or under estimation of solar and terrestrial radiation and climatic conditions of the surrounding areas and characteristics of land cover. Hence, these factors should be considered when applying these findings in urban and environment planning for improving the microclimate in urban areas.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.3 no.3
• /
• pp.3-12
• /
• 2000

The field surveys and the measurements of seawater temperatures were conducted every month from 1997 to 1999, and the distributions of seawater temperature were simulated and reproduced by a three dimensional hydrodynamic numerical model over the southern waters of Cheju island. In order to estimate the marine environmental capacity for the reception of the heat loads of cooling water discharged from Hwasoon Thermal Power Plant(HTPP) in the study area, the simulations for predicting the situation of unfavorable environment in which marine organisms might not be satisfied with change in seawater temperature were peformed using a three dimensional hydrodynamic numerical model by controlling quantitatively the heat loads of cooling water from HTPP Currently, HTPP discharges cooling water of 35.9℃ into the sea as much as 112,800m³/day in summer. As the results of simulations, the more the heat loads from the power plant increase, the more increase the seawater temperatures around the water areas adjacent to the power plant. In case the heat loads of cooling water from HTPP become about 5 times as high as the present loads, seawater temperatures at near-shore waters adjacent to HTPP appear to be increased to the extent of 0.5℃ above the existing seawater temperature in summer. The marine environmental capacity for the reception of thermal discharge from HTPP is estimated to be about 530×10/sup 6/kcal/day which is equivalent to the increase of a factor of 2 in the temperature of cooling water without any change in the discharge rate of cooling water or which is equivalent to the increase of a factor of 4.6 in the discharge rate of cooling water without any change in the temperature of cooling water. Comparing the case of the increase in the discharge rate of cooling water with the case of the increase in the temperature of cooling water on the basis of the same heat loads of 530×10/sup 6/kal/day, the former case is expected to increase seawater temperature a little higher and to extend the area affected by heat loads a little broader.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.20 no.2
• /
• pp.175-182
• /
• 2018

Knowledge of the optimum cultivation period for Chinese cabbage would help growers especially in spring in Korea. Growth and yield of Chinese cabbage in a temperature gradient chamber was evaluated for the growing periods of 64 days from three set of transplanting dates including March 6, March 20, and April 3 in 2017. Air temperature in the chamber was elevated step-by-step, by $2^{\circ}C$ above the ambient temperature. This increment was divided into three phases; i.e. low (ambient+$2^{\circ}C$, A), medium (ambient+$4^{\circ}C$, B), and high temperature (ambient+$6^{\circ}C$, C). The fresh weight of Chinese cabbage was greater under B and C conditions in the first period and A in the second period, which indicated that GDDs affected the fresh weight considerably. However, leaf growth (number, area, length, and width) did not differ by GDDs. Bolting appeared under A condition in the first period, which was caused by low temperature in the early growth stage. Soft rot was developed under C condition in the second period and all temperature conditions in the third period, which resulted from high temperature in the late stage. Fresh weight increased when GDDs ranged from 587 to 729. However, it decreased when GDDs > 729. The maximum expected yield (16.3 MT/10a) was attained for the growing period of 64 days from transplanting date during which GDDs reached 601. The GDDs for optimum cultivation ranged from 478-724 under which the yield was about 95% (15.5 MT/10a) of maximum fresh weight. Such an optimum condition for GDDs was validated at five main cultivation regions including Jindo, Haenam, Naju, Seosan, and Pyeongtaek in Korea. In these regions, GDDs ranged from 619-719. This suggested that the optimum GDDs for Chinese cabbage cultivation would range from 478-724, which would give the useful information to expect the cultivation periods for ensuring maximum yield.

• Journal of Bio-Environment Control
• /
• v.11 no.4
• /
• pp.151-156
• /
• 2002

Root zone cooling, such as soil or nutrient solution cooling, is less expensive than air cooling in the whole greenhouse and is effective in promoting root activity, improving water absorption rate, decreasing plant temperature, and reducing high temperature stress. The heat transfer of a soil cooling system in a plastic greenhouse was analyzed to estimate cooling loads. The thermal conductivity of soil, calculated by measured heat fluxes in the soil, showed the positive correlation with the soil water content. It ranged from 0.83 to 0.96 W.m$^{[-10]}$ .$^{\circ}C$$^{[-10]}$ at 19 to 36％ of soil water contents. As the indoor solar radiation increased, the temperature difference between soil surface and indoor air linearly increased. At 300 to 800 W.m$^{-2}$ of indoor solar radiations, the soil surface temperature rose from 3.5 to 7.$0^{\circ}C$ in bare ground and 1.0 to 2.5$^{\circ}C$ under the canopy. Cooling loads in the root zone soil were estimated with solar radiation, soil water content, and temperature difference between air and soil. At 300 to 600 W.m$^{-2}$ of indoor solar radiations and 20 to 40％ of soil water contents,46 to 59 W.m$^{-2}$ of soil cooling loads are required to maintain the temperature difference of 1$0^{\circ}C$ between indoor air and root zone soil.

• Food Science and Preservation
• /
• v.19 no.5
• /
• pp.633-638
• /
• 2012

The aim of this study was to investigate the growth of aerobic bacteria in fresh-cut salad during short-term temperature abuse ($4{\sim}30^{\circ}C$temperature for 1, 2, and 3 h) for 72 h and to develop predictive models for the growth of total viable cells (TVC) based on Predictive food microbiology (PFM). The tool that was used, Pathogen Modeling program (PMP 7.0), predicts the growth of Aeromonas hydrophila (broth Culture, aerobic) at pH 5.6, NaCl 2.5%, and sodium nitrite 150 ppm for 72 h. Linear models through linear regression analysis; DMFit program were created based on the results obtained at 5, 10, 20, and $30^{\circ}C$ for 72 h ($r^2$ >0.9). Secondary models for the growth rate and lag time, as a function of storage temperature, were developed using the polynomial model. The initial contamination level of fresh-cut salad was 5.6 log CFU/mL of TVC during 72 h storage, and the growth rate of TVC was shown to be 0.020~1.083 CFU/mL/h ($r^2$ >0.9). Also, the growth tendency of TVC was similar to that of PMP (grow rate: 0.017~0.235 CFU/mL/h; $r^2=0.994{\sim}1.000$). The predicted shelf life with PMP was 24.1~626.5 h, and the estimated shelf life of the fresh-cut salads with short-term temperature abuse was 15.6~31.1 h. The predicted shelf life was more than two times the observed one. This result indicates a 'fail safe' model. It can be taken to a ludicrous extreme by adopting a model that always predicts that a pathogenic microorganism will grow even under conditions so strict as to be actually impossible.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.6
• /
• pp.666-672
• /
• 1997

Twenty years' daily mean air temperature data was used to calculate the critical early seeding date(CESD), the optimum heading date(OHD), the critical late heading date for stable ripening(CHDR) and the critical late ripening date(CLRD) for rice seeded on dry paddy in different agroclimatic zones in Korea. The CESD was defined as the first day with mean air temperature of 13$^{\circ}C$, and the OHD as the first day of the 40 consecutive days with mean air temperature of 22$^{\circ}C$ or above after heading. The CHDR was defined as the date after which the cumulative daily mean air temperature would be at least 76$0^{\circ}C$. Lastly, the CLRD was defined as the last day when daily mean air temperature remains above 15$^{\circ}C$. This information was used for the estimation of periods from the earliest date of seeding to optimum heading date, the latest possible date of heading and the latest possible date of ripening in respective regions. For instance, in Suwon, those respective periods mentioned were found to be 104days, 124days, and 165days.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.17 no.4
• /
• pp.243-251
• /
• 2012

Real-time monitoring for environmental factors(temperature, salinity, chlorophyll, etc.) and carbonate components( pH and $fCO_2$) was conducted during 5-6th of July, 2012 at a seaweeds farm in Gijang, Busan. Surface temperature and salinity were ranged from $12.5{\sim}17.6^{\circ}C$ and 33.7~34.0, respectively, with highly daily and inter-daily variations due to tide, light frequency(day and night) and currents. Surface $fCO_2$ and pH showed a range of $381{\sim}402{\mu}atm$ and 8.03~8.15, and chlorophyll-a concentration in surface seawater ranged 0.8~5.8 ${\mu}g\;L^{-1}$. Environmental and carbonate factors showed the highest/lowest values around 5 pm of 5th July when the lowest tidal height and strongest thermocline in the water column, suggesting that biological production resulted in decrease of $CO_2$ and increase of pH in the seaweed farm. Processes affecting the surface $fCO_2$ distribution were evaluated using a simple budget model. In day time, biological productions by phytoplankton and macro algae are the main factors for $CO_2$ drawdown and counteracted the amount of $CO_2$ increase by temperature and air-sea exchange. The model values were a little higher than observed values in night time due to the over-estimation of physical mixing. The model suggested that algal production accounted about 14-40% of total $CO_2$ variation in seaweed farm.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.760-766
• /
• 2016

This study explored the effects of heating temperature and laminae thicknesses on the time required to heat the center of air-dried Paulownia tomentosa, Pinus sp., Abies sp., and Larix sp. laminae to $56^{\circ}C$, which is a minimum core temperature of wood packaging materials defined by ISPM 15 standard, and maintain for 30 minutes in dry heat treatment schedule. Heating times were different among wood species and were Pinus sp. ${\geq}$ Abies sp. > Paulownia tomentosa > Larix sp. in decreasing order. The differences in heating times of some species were significantly different statistically, but were not different enough in practical terms to warrant heating four species separately. Heating times decreased as heating temperature increased and followed approximately power-function relationship. Also, heating times increased linearly with increasing laminae thickness. These relationships make it possible to calculate intermediate heating times relative to experimentally observed heating times. The results of this study will serve as a guideline for heat sterilization of Chinese laminae species to meet heat treatment requirements for protection against invasive pests.

• Korean Journal of Food Science and Technology
• /
• v.47 no.6
• /
• pp.797-800
• /
• 2015

The effect of raw wheat flour on starch retrogradation retardation was investigated in a rice starch paste model. Specifically, in terms of amylase activity present in the wheat flour, the retardation effect was investigated depending on reaction temperature (40, 60, and $80^{\circ}C$), incubation time (0, 20, 40, and 60 min), and wheat flour addition levels (0-10%). An increase in wheat flour concentration resulted in a rapid decrease in the elastic modulus (G') as the incubation time increased. The G' changes of the rice starch pastes were furthermore fitted by the first order reaction for the reaction rate estimation on the temperature basis. The experimental reaction rate of the paste sample incubated with 10% wheat flour at $40^{\circ}C$ exhibited good agreement with the predicted value. This result implied that the first order reaction kinetics could be suitable to predict the changes in the G' as a function of incubation temperature and wheat flour concentration.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.653-660
• /
• 2007

Since the temperature of asphalt for deck plate of steel bridge during paying procedure is relatively high as $240^{\circ}C\;to\;260^{\circ}C$, the temperature of deck plate of bridge rises mere than $100^{\circ}C$ and excessive displacement and stress could occur. In order to avoid undesirable failure of base plate and determine the optimal pavement pattern, a thorough thermal analysis is needed. General structural model which is made of beam and plate element should be modified for transient heat transfer analysis; asphalt pavement material and convection effect on surface of structure need to be added. A new technique with the Equivalent Heat Source (EHS) for numerical thermal analysis for steel bridge under thermal load of Guss asphalt pavement is proposed. Since plate/beam elements which were generally used for structural analysis for bridge cannot explain convection effect easily on plate/beam surface, EHS which is determined based on calculated temperature with convection effect is used. To verify the EHS proposed in this study, numerical analyses with plate elements are performed and the results are compared with estimated temperatures. EHS might be used for other thermal analyses of steel bridge such as welding residual stress analysis and bridge fire analysis.