• 대한전자공학회논문지SD
• /
• 제46권10호
• /
• pp.1-8
• /
• 2009

본 논문에서는 아날로그 및 디지털 집적시스템에서 사용될 수 있는 온도변화에 무관한 파워-업 검출기 회로를 제안하였다. 제안된 파워-업 검출기는 트랜지스터의 문턱전압과 이동도의 상호 온도보상 기술을 이용하여 nMOS 분압기와 pMOS 분압기의 출력 전압이 온도에 무관한 특성을 갖도록 하여 온도 변화에 따른 파워-업 전압의 변화량을 최소화하였다. 68-nm CMOS 공정을 이용한 시뮬레이션 결과, 제안된 파워-업 검출기는 파워-업 전압 1.0V 기준으로 $-30^{\circ}C$에서 $90^{\circ}C$의 온도변화 조건에서 4 mV의 매우 작은 파워-업 감지 전압 변화량을 갖는 출력 특성을 보였고, 기존 회로에 비해 92.6%의 파워-업 감지 전압 변화량 감소를 확인하였다.

• 센서학회지
• /
• 제25권5호
• /
• pp.377-381
• /
• 2016

NDIR $CO_2$ gas sensor was prototyped with ASIC implemented thermopile sensor which included temperature sensor and White-Cell structure in this paper. The temperature dependency of dual infrared sensors ($CO_2$ and reference IR sensors) has been characterized and their output voltage ratios according to the temperature and gas concentration were presented in this paper for achieving temperature compensation algorithm. The initial output voltages of NDIR $CO_2$ gas and reference IR sensors showed $3^{rd}$ order polynomial and linear output voltages according to the variation of ambient temperatures from 253 K to 333 K, respectively. The output voltages of temperature sensor presented a linear dependency according to the ambient temperature and could be described with V(T) = -3.0069+0.0145T(V). The characteristics of output voltage ratios could be modeled with five parameters which are dependent upon the ambient temperatures and gas concentration. The estimated $CO_2$ concentrations showed relatively high error below 300 ppm (maximum 572 % at 7 ppm $CO_2$ concentration), however, as the concentration increased from 500 ppm to 2,000 ppm, the overall estimated errors of $CO_2$ concentrations were less than ${\pm}10%$ in this research.

• 한국건축시공학회지
• /
• 제21권6호
• /
• pp.563-571
• /
• 2021

최근 초고층 아파트 및 주상복합 건축물의 증가로 두께 3m이상의 메가급 매스콘크리트 부재의 설계가 다수 수행되고 있다. 초고층 주상복합 건축물은 기초부재 뿐만 아니라 특수한 구조형태로 전이 보 및 슬라브 등과 같은 매스콘크리트 시공이 증가하고 있어 매스콘크리트의 온도균열저감에 관한 연구가 수행되고 있다. 매스콘크리트의 온도균열을 검토하기 위해서는 콘크리트 열특성 검토가 중요하나 현장에서 단열온도상승 시험기를 활용하기는 어렵기 때문에 간이-단열온도상승시험을 주로 활용한다. 본 연구에서는 간이-단열온도상승시험에 의한 콘크리트 열특성 결과의 정밀도를 향상시키기 위해 열손실을 보정하기 위한 방안과 열손실 보정에 미치는 다양한 요인을 검토하여 제시하였다.

• 한국인터넷방송통신학회논문지
• /
• 제19권6호
• /
• pp.87-93
• /
• 2019

본 논문에서는 밀리미터파(Ka-밴드) 탐색기를 이용한 라디오미터 설계에 대해서 다룬다. 라디오미터는 TPR(Total Power Radiometer) 방식을 적용하였고, 이를 위해 IF-Drive amp, 대역통과필터(BFP), 검출기(Detector) 및 Op-amp를 구성하였다. 라디오미터는 잡음 수준의 신호를 측정하는 센서로서 시스템의 온도 변화에 따라 측정값이 상이하게 달라질 수 있다. 이를 해결하기 위해 온도보정 회로가 없는 라디오미터 구조에서의 밝기온도 보상 방안을 적용하여 보정을 수행하였다. 설계된 라디오미터를 이용하여 표적, 특히 차량과 지표면을 구분하는 실험을 수행하였고, 일정 이상의 BFF(Beam Fill Factor)를 만족하는 경우 표적과 배경을 구분함을 확인하였다.

• 한국전자파학회논문지
• /
• 제26권9호
• /
• pp.798-805
• /
• 2015

본 논문에서는 랜덤 수 생성 회로를 통해 Relaxation Oscillator의 주파수를 불규칙하게 변환하여 EMI Noise를 최소화하는 방법을 제시한다. 또한, DC-DC Converter에 이 기법이 적용되었을 때의 효과와 이 결과가 RF Receiver system에 미치는 효과를 Noise 측면에서 연구하였다. 제안하는 Relaxation Oscillator 출력 중심주파수는 7.9 MHz이고, 온도보상기법을 적용하여 온도변화에 따라 주파수가 보상되도록 설계하였다. 이 칩은 $0.18{\mu}m$ 공정으로 설계하였고, 칩의 면적은 $220{\mu}m{\times}280{\mu}m$이다. 전류 소모는 공급전압인 1.8 V에서 $500{\mu}A$이다.

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.59-67
• /
• 2014

PURPOSES : The purpose of this study is to analyse the longitudinal steel strain and stress of continuously reinforced concrete pavement(CRCP) with longitudinal and transverse direction at early age using stress dependent strain analysis method. METHODS : To measure the longitudinal steel strain, 9-electrical resistance and self-temperature compensation gauges were installed to CRCP test section (thickness = 250mm, steel ratio = 0.7%) and continuously measured 10min. intervals during 30days. In order to properly analyze the steel stress first, temperature compensation process has been conducted. Secondly, measured steel strains were divided into stress dependent strain (elastic strain) and stress independent strain (thermal strain) and then stress dependent strain was applied to stress calculation of longitudinal steels. RESULTS : Steel strains were successfully measured during 30days. To verify the accuracy of temperature compensation process, measured coefficient of thermal expansion(COTE,$11.46{\times}10^{-6}m/m/^{\circ}C$) of longitudinal steel before paving was compared with that of unrestrained steel. Max. steel stress in the transverse direction shows about 266MPa at 23days after placement. CONCLUSIONS : Steel stresses in the longitudinal and transverse direction have been evaluated. In longitudinal direction, steel stress from the crack was rapidly reduced from 183MPa at crack to 18MPa from 600mm apart the crack. From this observation, stress effective length can be identified as within 600mm apart from the crack. In transverse direction, max. stress point was located near the center of pavement width and stress level(266MPa) is about 66% of yield stress of steel.

• 센서학회지
• /
• 제25권4호
• /
• pp.291-296
• /
• 2016

The ideal chemical sensor must show the similar result under the same condition for accurate measurement of gases regardless of time. However, the actual responses of chemical sensors have been shown the lacks of repeatability and reproducibility because of the drift which has been caused by aging and pollution of the sensor and the environment change such as temperature and humidity. If the problems are not properly taken into considerations, the stability and reliability of the system using chemical sensors would be decreased. In this paper, we analyzed the sensor's drift and applied the three different compensation methods(DWT( Discrete Wavelets Transform), Baseline Manipulation, Internal Normalization) for reducing the effects of the drift in order to improve the stability and the reliability of short term of the chemical sensors. And in order to compare the results of the methods, the standard deviation was used as a criterion. The sensor drift was analyzed by a trend line graph. We applied the three methods to the successive data measured for three days and compared the results. As a result of comparison, the standard deviation of DWT showed lowest value. (Before compensation: 7.1219, DWT: 1.3644, Baseline Manipulation: 2.5209, Internal Normalization: 3.1425).

• 한국산학기술학회논문지
• /
• 제13권3호
• /
• pp.1263-1269
• /
• 2012

본 논문은 광 통신용 CWDM(Coarse Wavelength Division Multiplexing) 광 송수신기 레이저에 히터를 내장시켜 저온 파장을 보상하기 위한 연구이다. 일반적으로 DFB(Distributed Feedback) 레이저 파장의 온도 변화량은 약 $0.1nm/^{\circ}C$ 정도이다. 즉 온도가 올라가면 파장도 올라가고, 온도가 내려가면 파장도 내려간다. 따라서 각 채널별 기준 중심 파장간의 간격이 20 nm인 CWDM 광 통신망에서는 근접 채널 간의 파장 간섭을 막기 위해서 동작 온도 범위를 넓힐 수 없는 문제를 갖고 있다. 이를 보완하기 위해 히터를 CWDM LD(Laser Diode) TO-CAN 패키지 바닥면에 부착하여 저온에서의 파장을 보상할 수 있다. 따라서 이를 이용해서 산업용 광 송수신기 동작 온도 범위인 $-40{\sim}+85^{\circ}C$에서 기준 파장대비 +/-6.5 nm 변화폭에 만족시킬 수가 있었다.

• 센서학회지
• /
• 제27권1호
• /
• pp.47-54
• /
• 2018

In this paper, we describe the thermal characteristics of the output voltages of ethanol gas sensor according to the amount of radiation incident on the infrared sensors located at each focal point of two elliptical waveguides. In order to verify the output characteristics of the gas sensor according to the amount of incident light on the infrared sensor, two combinations of sensor modules were fabricated. Hydrophobic thin film is deposited on one of the reflectors of sensor modules and one of the two infrared sensors was equipped with a hollow disk (10 Ø), and the temperature characteristics of the infrared sensor equipped with the hollow disk (10 Ø) and the infrared sensor without the disk were tested. The temperature was varied from 253 K to 333 K at 10 K intervals based on 298 K. The properties of ethanol gas sensor have been identified with respect to varying temperature for a range of ethanol concentration from 0 ppm to 500 ppm. In the case of an infrared sensor equipped with a hollow disk (10 Ø), the output voltage of the sensor decreased by 0.8 mV and 1 mV, respectively, as the temperature increased. Conversely, the output voltage of the diskless infrared sensor showed an average increase of 67 mV and 57 mV as the temperature increased. The ethanol concentrations estimated on the basis of results show an error of more than 10 % for less than 100 ppm concentration. However, if the ethanol concentration exceeds 100 ppm, the gas concentration can be estimated within the range of ${\pm}10%$.

• 한국정밀공학회지
• /
• 제30권7호
• /
• pp.754-761
• /
• 2013

Thermal displacement is an important issue in machine tool systems. During the last several decades, thermal error compensation technology has significantly reduced thermal distortion error; this success has been attributed to the development of a precise, robust thermal error model. A major advantage of using the thermal error model is instant compensation for the control variables during the modeling process. However, successful application of thermal error modeling requires correct determination of the temperature sensor placement. In this paper, a procedure for predicting thermal-mode-based thermal error is introduced. Based on this thermal analysis, temperature sensors were positioned for multiple heat-source models. The performance of the sensors based on thermal-mode error analysis, was compared with conventional methods through simulation and experiments, for the case of a slide table in a transient state. Our results show that for predicting thermal error the proposed thermal model is more accurate than the conventional model.