• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.140-140
• /
• 2018

The 3D interconnect technologies have been appeared, as the density of Integrated Circuit (IC) devices increases. Through Silicon Via (TSV) process is an important technology in the 3D interconnect technologies. And the process is used to form a vertically electrical connection through silicon dies. This TSV process has some advantages that short length of interconnection, high interconnection density, low electrical resistance, and low power consumption. Because of these advantages, TSVs could improve the device performance higher. The fabrication process of TSV has several steps such as TSV etching, insulator deposition, seed layer deposition, metallization, planarization, and assembly. Among them, TSV metallization (i.e. TSV filling) was core process in the fabrication process of TSV because TSV metallization determines the performance and reliability of the TSV interconnect. TSVs were commonly filled with metals by using the simple electrochemical deposition method. However, since the aspect ratio of TSVs was become a higher, it was easy to occur voids and copper filling of TSVs became more difficult. Using some additives like an accelerator, suppressor and leveler for the void-free filling of TSVs, deposition rate of bottom could be fast whereas deposition of side walls could be inhibited. The suppressor was adsorbed surface of via easily because of its higher molecular weight than the accelerator. However, for high aspect ratio TSV fillers, the growth of the top of via can be accelerated because the suppressor is replaced by an accelerator. The substitution of the accelerator and the suppressor caused the side wall growth and defect generation. The suppressor was used as Single additive electrodeposition of TSV to overcome the constraints. At the electrochemical deposition of high aspect ratio of TSVs, the suppressor as single additive could effectively suppress the growth of the top surface and the void-free bottom-up filling became possible. Generally, copper was used to fill TSVs since its low resistivity could reduce the RC delay of the interconnection. However, because of the large Coefficients of Thermal Expansion (CTE) mismatch between silicon and copper, stress was induced to the silicon around the TSVs at the annealing process. The Keep Out Zone (KOZ), the stressed area in the silicon, could affect carrier mobility and could cause degradation of the device performance. Cobalt can be used as an alternative material because the CTE of cobalt was lower than that of copper. Therefore, using cobalt could reduce KOZ and improve device performance. In this study, high-aspect ratio TSVs were filled with cobalt using the electrochemical deposition. And the filling performance was enhanced by using the suppressor as single additive. Electrochemical analysis explains the effect of suppressor in the cobalt filling bath and the effect of filling behavior at condition such as current type was investigated.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.1
• /
• pp.58-62
• /
• 2007

Digital communication is important for reliability and mobilization of the multi-channel communication systems. Transmitting and receiving data for the mobilization should be possible in anywhere and in anytime. And this system must be designed light weight small size and low power. One are essential technology for implementing the mobile wireless communication system on the age of ubiquotos. Requirements in constructing such communication field are followings. At first data transmitting and receiving should be carried out by a simple command. Second, the device should be designed as hand-hold type and low power consumption. Third, data communication should be reliable. As one of examples, car to car system which is popular in the market is introduced here, All traffic information in highway is transmitted from one car to another by using this system which can prevent possible traffic accident. This paper shows the design of a digital data communication system with CC1020 chip. This CC1020 makes easy frequency selection and easy switch from the transmit mode to the receive mode by simple setting of a memory register in the chip. The transmit power of this system is designed 10dBm and its communication range is about 100m. The power supplied this system is 3V considered as low power. The sleep mode can be easily entered during transmit mode or receive mode. We shows the program algorithm of CC1020 and interface circuit between MCU and CC1020. We shows the Photo of the CC1020 Module and Atmega128 Module.. We analysed the receiver rate with this system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.1B
• /
• pp.21-30
• /
• 2012

Sensor networks are composed of a great number of sensor nodes with constrained battery. Disjoint multipath scheme based flooding method has a merit that efficiently construct multipath in irregular networks, but causes lots of energy consumption in networks. Flooding method is not a suitable technology in wireless sensor networks with constrained battery. We introduce energy-efficient geographic routing scheme considered as an efficient, simple, and scalable routing protocol for wireless sensor networks. The geographic routing scheme on multipath generates a problem with a congestion. So we introduce the concept of multipath pipeline as a congestion avoidance strategy. But multipath pipelines have a big problem on the boundary of holes under irregular networks. We propose a novel disjoint multipath scheme as combined method with geographic routing scheme and hole detouring algorithm on multipath. A novel disjoint multipath scheme constructs disjoint multipath pipelines efficiently for reliability without a collision in irregular wireless sensor networks. Simulation results are provided to validate the claims.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.900-905
• /
• 2016

The field of power system harmonics has been receiving a great deal of attention recently. This is primarily due to the fact that non-linear (or harmonic-producing) loads comprise an ever-increasing portion of what is handled at a typical industrial plant. The incidence rate of harmonic-related problems is low, but awareness of harmonic issues can still help increase offshore power plant system reliability. On the rare occasion that harmonics become a problem, this is either due to the magnitude of harmonics produced or power system resonance. This harmonic study used an electrical configuration for the offloading scenario of a Floating LNG (FLNG) unit, considering power load. This electrical network configuration is visible in the electrical network load flow study part of the project. This study has been carried out to evaluate the performance of an electric power system, focusing on the harmonic efficiency of an electrically driven motor system to ensure offshore plant safety. In addition, the design part of this study analyzed the electric power system of an FLNG unit to improve the safety of operation and maintenance.

• Journal of Digital Convergence
• /
• v.14 no.1
• /
• pp.413-425
• /
• 2016

This study investigated what effects the relational benefits perceived by the customers of solely operated beauty salons have on customer satisfaction, recommendation intention, and defection intention through the convergence of cosmetology and business management. For this, a total of 322 customers of solely operated beauty salons were chosen as final valid samples. For data analysis, frequency analysis, reliability analysis, confirmatory factor analysis, and correlation analysis were performed using SPSS 15.0 and AMOS 18. For a hypothesis test, lastly, path analysis was conducted using structural equation modeling. The study results found the following: First, among the relational benefits perceived by the customers of solely operated beauty salons, confidence benefits and social benefits had a positive effect on customer satisfaction. Second, the relational benefits perceived by the customers of solely operated beauty salons had a positive effect on recommendation intention. Third, confidence benefits and social benefits had a negative effect on defection intention. Fourth, customer satisfaction had a positive effect on recommendation intention. Fifth, customer satisfaction had a negative effect on defection intention. Sixth, in relationship between the relational benefits perceived by the customers of solely operated beauty salons and recommendation/defection intention, customer satisfaction revealed partial mediating effects.

• Journal of Convergence for Information Technology
• /
• v.10 no.11
• /
• pp.156-167
• /
• 2020

The purpose of this study is to analyze the influence of the mindset on stress and job performance. For the analysis, a questionnaire is conducted for cabin crew members in K airlines, and a total of 266 copies are used for the final analysis. To verify the hypotheses of the study, frequency analysis, exploratory factor analysis, reliability analysis, confirmatory factor analysis, measurement model analysis, validation of the measuremen model, and structural equation model analysis are used based on the questionnaire. First, it is confirmed that the mindset had a negative (-) effect on the cabin crew's role stress, reward stress and relationship stress. Second, it is found that cabin crew's reward stress have a negative (-) effect on job performance. On the other hand, relationship stress is found to have a positive influence on job performance and there is no significant result in effect with role stress. Third, the mindset showes a significant positive impact relationship on job performance. As a result, it is necessary to introduce a mindset intervention program so that it can be applied in practical work. These research results confirm the positive effects of mindsets and show that they contribute to organizational performance. In addition, it is necessary to prepare a program to change the mindset of airline cabin crew and to be applied in actual work.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.143-147
• /
• 2017

To evaluate surface characteristics and improve crystalline quality of AlN single crystal grown by physical vapor transport (PVT) method, wet chemical etching process using $KOH/H_2O_2$ mixture in a low temperature condition and thermal annealing process was proceeded respectively. Conventional etching process using strong base etchant at a high temperature (above $300^{\circ}C$) had formed over etching phenomenon according to crystalline quality of materials. When it occurred to over etching phenomenon, it had a low reliability of dislocation density because it cannot show correct number of etch pits per estimated area. Therefore, it was proceeded to etching process in a low temperature (below $100^{\circ}C$) using $H_2O_2$ as an oxidizer in KOH aqueous solution and to be determined optimum etching condition and dislocation density via scanning electron microscope (SEM). For improving crystalline quality of AlN single crystal, thermal annealing process was proceeded. When compared with specimens as-prepared and as-annealed, full width at half maximum (FWHM) of the specimen as-annealed was decreased exponentially, and we analyzed the mechanism of this process via double crystal X-ray diffraction (DC-XRD).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.89-96
• /
• 2009

As increasing the number of digital control devices installed on aircrafts and their transmission speed, various digital data buses have been introduced to provide reliable and high-speed characteristics. These characteristics of avionics data bus are highly related on the fault-tolerant performance which can make minimize jitter and loss during data transfer. In this paper, we concerned about a new traffic shaping scheme for increasing the reliability of Avionics Full Duplex Switched Ethernet (AFDX) systems based on ARINC 664 standard. We note that the conventional AFDX with a single regulator per virtual link system may produce aggregated traffics as the number of virtual links increasing. The aggregated traffic results in large jitters among frames. To remedy for the jitter and loss of data, we propose a dual regulator scheme for the AFDX system. The purpose of the additional regulator is to additionally regulate aggregated traffics from a number of per virtual link regulators. Using NS-2 simulator, we show that the proposed scheme provides a better performance than the single regulator one. It is worthwhile note that the proposed AFDX with Dual Regulator scheme can be employed to not only aircraft networks but other QoS sensitive networks for robot and industrial control systems.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.975-982
• /
• 2005

Scientific community agrees about the fact that base Isolation provides interesting solutions to minimize the seismic risk. Reliability of such a technique is nowadays proofed by a large number of applications like public buildings, nuclear plants, bridges, etc. This paper reports the results of performance verification tests of the base isolated RC building with the laminated rubber bearings which is manufactured by enterprise in Korea. The shaking table tests were performed using a three story model scaled to 1/3 of the prototype RC apartment building. Several major earthquake records were scaled to different peak ground accelerations and used as input base excitations. Especially in this study, effect of earthquake characteristics on response reduction and effect of the intensity of excitations are studied. Through the verification tests, the validity of the applied base isolaion device and the response reduction effect against earthquakes are confirmed.

• The KIPS Transactions:PartD
• /
• v.15D no.6
• /
• pp.767-776
• /
• 2008

Microarray technology is extensively being used in experimental molecular biology field. Microarray experiments generate quantitative expression measurements for thousands of genes simultaneously, which is useful for the phenotype classification of many diseases. One of the two major problems in microarray data classification is that the number of genes exceeds the number of tissue samples. The other problem is that current methods generate classifiers that are accurate but difficult to interpret. Our paper addresses these two problems. We performed a direct integration of individual microarrays with same biological objectives by transforming an expression value into a rank value within a sample and generated rank-comparison decision rules with variable number of genes for cancer classification. Our classifier is an ensemble method which has k top scoring decision rules. Each rule contains a number of genes, a relationship among involved genes, and a class label. Current classifiers which are also ensemble methods consist of k top scoring decision rules. However these classifiers fix the number of genes in each rule as a pair or a triple. In this paper we generalized the number of genes involved in each rule. The number of genes in each rule is in the range of 2 to N respectively. Generalizing the number of genes increases the robustness and the reliability of the classifier for the class prediction of an independent sample. Also our classifier is readily interpretable, accurate with small number of genes, and shed a possibility of the use in a clinical setting.