• Journal of ILASS-Korea
• /
• v.26 no.1
• /
• pp.9-17
• /
• 2021

Six shear coaxial injectors with different recess length and taper angle were manufactured. Cold-flow tests on the injectors were performed at room temperature and pressure using water and air as simulants. By changing the water mass flow rate and air mass flow rate, spray images were taken under single-injection and bi-injection. Breakup length and spray angle were analyzed from instantaneous and averaged spray images using image processing techniques. For all the injectors, the breakup length generally decreased as the momentum flux ratio increased at the same gas mass flow rate. The injectors with 7.5° taper angle usually had the longest breakup length and the smallest spray angle. When the taper angle was 15° or more, it hardly affected breakup length and spray angle. The recess length did not influence breakup length but its effect on spray angle depended on the taper angle.

• Tribology and Lubricants
• /
• v.34 no.1
• /
• pp.16-22
• /
• 2018

Cylindrical turbine guide bearings (TGBs) with simple plain pads have conventionally been used in vertical hydro-power turbine-generator applications in order to provide turbine runner shafts with smooth rotation guides and supports. To overcome low-load/low-eccentricity performance drawbacks, such as very low film stiffness and lack of design credibility in the stiffness values themselves, of conventional cylindrical TGBs, the introduction of a rotational-directional leading-edge taper to each partitioned pad, simply pad leading-edge taper, has been found to be very effective in enhancing their design-application availability and usefulness. In this study, we investigate the effects of taper angle and length for given taper heights in detail in order to systematically establish the effectiveness of design on the performance improvement of vertical hydro-power application cylindrical TGBs with pad leading-edge tapers. The analysis results with $4-Pad{\times}1-Row$ cylindrical TGBs show that the lubrication performance of the cylindrical TGBs is optimized with an approximate taper angle ratio of 0.8 and taper length ratio of 0.9. We conclude that the introduction of pad leading-edge tapers along with the optimization of taper designs can be very effective in improving the overall operation reliability of cylindrical TGBs and the rotordynamic characteristics of vertical hydro-power turbine-generator rotor-bearing systems as well, to which the TGBs are applied.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.6
• /
• pp.71-75
• /
• 1985

Transmission characteristics of a linear double rectangular taper is analysed by the trans-mission matrix of the taper. The total transmission matrix of the taper is obtained by multiplication of transmission matrices of smrjll taper sections which is decided into uniform length along the taper axis. The VSWR calculated from the transmission matrix is compared with those of Johnson and Matsumaru.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.362-364
• /
• 1993

The properties of near-field diffraction by small aperture are investagated and using of optical fiber taper as a small aperture are proposed. Near-field diffracted by aperture smaller than one wave length can overcome the resolution of conventional microscopy and optical component. In this paper production methods of sub-wave length optical fiber taper using solenoid are also proposed.

• Restorative Dentistry and Endodontics
• /
• v.45 no.4
• /
• pp.51.1-51.10
• /
• 2020

Objectives: No studies have yet assessed vibration characteristics according to endodontic file length. Accordingly, the objective of the present study was to examine the vibration characteristics according to nickel-titanium file length and to compare these characteristics between different file systems. Materials and Methods: A total of 45 root canal models were divided into 3 experimental groups (n = 15 each) based on the file system used (ProTaper Gold [PTG], ProTaper Next, or WaveOne Gold [WOG]). Each experimental group was further divided into 3 subgroups according to file length (21, 25, or 31 mm). An electric motor (X-SMART PLUS) was used in the experiment. For each file system, vibrations generated when using a size 25 file were measured and used to calculate the average vibration acceleration. The differences in vibrations were analyzed using 1-way analysis of variance and the Scheffé post hoc test with a confidence interval of 95%. Results: In the PTG file system, significantly lower vibration acceleration was observed when using a 21-mm file than when using a 31-mm file. In the WOG file system, significantly stronger vibration acceleration was observed when using a 31-mm file than when using 21- or 25-mm files. Regardless of the file length, the WOG group exhibited significantly stronger vibration acceleration than the other 2 experimental groups. Conclusions: In clinical practice, choosing a file with the shortest length possible could help reduce vibrations. Additionally, consideration should be given to vibrations that could be generated when using WOG files with reciprocating motion.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.97-101
• /
• 2009

STATEMENT OF PROBLEM. Unlike screw-retention type, fixture-abutment retention in Locking taper connection depends on frictional force so it has possibility of abutment to sink. PURPOSE. In this study, Bicon$^{(R)}$ Implant System, one of the conical internal connection implant system, was used with applying loading force to the abutments connected to the fixture. Then the amount of sinking was measured. MATERIAL AND METHODS. 10 Bicon$^{(R)}$ implant fixtures were used. First, the abutment was connected to the fixture with finger force. Then it was tapped with a mallet for 3 times and loads of 20 kg corresponding to masticatory force using loading application instrument were applied successively. The abutment state, slightly connected to the fixture without pressure was considered as a reference length, and every new abutment length was measured after each load's step was added. The amount of abutment sinking (mm) was gained by subtracting the length of abutment-fixture under each loading condition from reference length. RESULTS. It was evident, that the amount of abutment sinking in Bicon$^{(R)}$ Implant System increased as loads were added. When loads of 20 kg were applied more than 5 - 7 times, sinking stopped at $0.45{\pm}0.09\;mm$. CONCLUSION. Even though locking taper connection type implant shows good adaption to occlusal force, it has potential for abutment sinking as loads are given. When locking taper connection type implant is used, satisfactory loads are recommended for precise abutment location.

• Restorative Dentistry and Endodontics
• /
• v.31 no.2
• /
• pp.125-132
• /
• 2006

This study was conducted to evaluate the insertion depth of Buchanan plugger after shaping by various Ni-Ti rotary files. It was conducted to determine which size of plugger are appropriate, when root canals are shaped with Ni-Ti rotary files and obturated by Continuous wave of condensation technique. Two type of eighty simulated resin blocks were used : J-shaped and straight shaped canal. The simulated canals were instrumented by ProTaper and ProFile. Buchanan pluggers were inserted into the canal, and then the image was recorded to scanner. The distance from the apex of the canal to the plugger tip was measured by image analysis program. Data were analyzed by one-way ANOVA followed by Scheffe's test. The results were as follows 1. In straight canal finished up to ProTaper F2 and F3 file, F and FM pluggers were inserted more than 5 mm short of working length. 2. In J-shaped canal finished up to ProTaper F2 file, F pluggers were inserted more than 5 mm short of working length. Finished up to ProTaper F3 file. F and FM pluggers were inserted more than 5 mm short of working length. 3. In straight and J-shaped canal finished up to ProFile .06/#20 and .06/#25, any of Buchanan plugger could not be inserted more than 5 mm short of working length. These results suggest that canals shaped by ProTaper could be obturated by Continuous wave of condensation technique with F and FM size Buchanan plugger.

• The korean journal of orthodontics
• /
• v.37 no.2 s.121
• /
• pp.89-97
• /
• 2007

Objective: The purpose of this study was to measure the insertion torque of orthodontic miniscrews regarding changes in their shape, diameter, and length. Methods: Torque values were measured during continuous insertion of the miniscrews into solid rigid polyurethane foam, using a torque tester of driving motor type with a regular speed of 3 rpm. Orthodontic miniscrews (Biomaterials Korea, Seoul, Korea) of cylindrical type and taper type were used. Results: Increasing the length and diameter of the miniscrews increased the maximum insertion torque value in both cylindrical and taper type screws. Insertion torque was increased at the incomplete head of the cylindrical type screw, and at the tapered part of the taper type screw. The insertion torque value of miniscrews was influenced most by diameter, then shape and length. As a result, it was shown that the diameter of the screw had the most influence on insertion torque, and the taper type screw had a higher torque value than the cylindrical type screw. Conclusion: Therefore, a large diameter or taper type screw are adequate for areas of thin cortical bone with a large interdental space, and a small diameter or cylindrical type screw are adequate in the mandibular molar area or the midpalatal area having thick cortical bone.

• Korean Journal of Computational Design and Engineering
• /
• v.6 no.3
• /
• pp.206-214
• /
• 2001

This paper describes the wire EDM (Electric Discharge Machining) CAM system considering a variable taper wire-cut and an unmanned wire EDM during the night. Wire EDM is applicable to all materials that are fairly good electrical conductors, including metals, alloys and most carbide. Thus it provides a relatively simple method for making holes of any desired cross section in materials that are too hard or brittle to be machined by most other methods. In this paper we classify variable taper wire-cut machining patterns and variable taper wire-cut geometries. Also we determine unmanned wire EDM patterns fur the productivity of wire EDM industry. Developed system consists of two modules: 1) Variable taper wire EDM module guarantees the length ratio machining function, the parametric ratio machining function and the marking function. 2) Unmanned wire EDM module guarantees the automatic wire EDM during the night. The proposed system has been tested in the fields and found to be a useful system.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.2
• /
• pp.45-52
• /
• 1994

A curvature variable taper is proposed for a waveguide-microstrip transition. It is applied to a ridge waveguide. The curvature depends on the taper length and difference of waveguide's height and microstrip substrate's height. The taper is manufactured easier than the other tapers. It's reflection coefficient is smaller than the parabolic taper's below one wavelengrh. The results of experiment show that S$_{11}$ is below -20dB and SS$_{21}$ is about -0.5dB in the band of 10~15 GHz. These results are good agreement with the theoritical values.