• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.37-45
• /
• 2006

The viscoelastic properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by dynamic mechanical thermal analysis (DMTA). Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The DMTA thermogram of MF resin showed that the storage modulus (E') increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. The storage modulus (E') of MF resin increased both as a function of increasing temperature and with increasing heating rate. From isothermal DMTA results, peak $T_{tan{\delta}}$ values, maximum value of loss modulus (E") and the rigidities (${\Delta}E$) of MF/PVAc blends at room temperature as a function of open time, peak $T_{tan{\delta}}$ and maximum loss modulus (E") values were found to increase with blend MF content. Moreover, the rigidities of the 70:30 and 50:50 MF/PVAc blends were higher than those of the other blends, especially of 100% PVAc or MF. We concluded that blends the MF/PVAc blend ratios correlate during the adhesion process.

• Rubber Technology
• /
• v.9 no.1
• /
• pp.1-12
• /
• 2008

Effects of silane modifier, bis(triethoxysilylpropyl) tetrasulfide (TESPT(S4)) and bis(triethoxysilylpropyl) disulfide (TESPD(S2)), on silica filled compound were investigated upon processability, dynamic, mechanical, heat build-up, blowout properties, and silica dispersion in natural rubber (NR). The temperature of the S2 treated silica compound generated higher than that of the S4 treated compound during internal mixer compounding. The shear viscosity of the S2 compound exhibited lower than that of the S4 compound and the viscosity measured in dynamic mode was close to each other. The elongation modulus of the S2 compound exhibited lower than that of the S4; however, the tear resistance strength of the S2 compound exhibited higher than that of the S4 compound. The loss tan$\delta$ values of the S2 compound exhibited higher than those of the S4 at room temperature. The augmentation of the test temperature lowered the tan$\delta$ values of each compound, which results in close tan$\delta$ values to each other at $100^{\circ}C$. The S2 compound deformed less than the S4 compound, and the blowout time of each compound was close to each other. The S2 compound generated more heat build-up than the S4 compound. The abrasion loss of the S2 compound was less than that of the S4 compound. The size of the silica agglomerate reduced on both S4 and S2 compounds upon vulcanization. The addition of the bifunctional silanes (S2 and S4) on silica filled NR compound improved the processability of each compound and their effects were more significant on the S2 compound than the S4 compound. After vulcanization the silica agglomerate size of each compound reduced compared with before vulcanization.

• Fashion & Textile Research Journal
• /
• v.15 no.6
• /
• pp.985-992
• /
• 2013

Polytrimethylene terephthalate(PTT) offers several advantageous properties such as good tensile strength, uniformity, stiffness, toughness, UV stability, resilience, stain resistance, outstanding elastic recovery, and dyeability. The effects of annealing temperature on physical properties and the structure of PTT filaments and yarn were investigated by measuring wide-angle X-ray diffraction (WAXD), density, optical birefringence, dynamic visco elasticity, and tensile testing. The intensity of maximum tan ${\delta}$ decreased and the temperature of maximum tan ${\delta}$ shifted to a higher temperature as the annealing temperature of filaments increased; however, it shifted to a lower temperature when the annealing temperature exceeded $130^{\circ}C$. In addition, crystallinity, density and D-spacing of (010) crystal face increased as the annealing temperature increased. Optical birefringence and specific stress were almost constant up to $100^{\circ}C$ and then decreased above $130^{\circ}C$. The shrinkage of PTT filament is 0 in boiling water when annealed above $130^{\circ}C$; consequently, the use of annealed fiber above $130^{\circ}C$ can remove thermal instability when dyeing PTT fiber. In the case of yarns, the thermal stability and physical properties of yarns showed the best effect when the ply number is less than 5, twist number is less than 400tpm, and the annealing time is 20minutes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.5
• /
• pp.207-212
• /
• 2015

Continuous, high-quality supply of electrical energy is the backbone of any modern economy. Any equipment operating at a power station must be reliable and safe. All major power supply components such as transformers, cables, generators, and switchgear need to be kept in perfect operating condition. The lifetime of power cables, used as the main means of transferring electric power, is understood to be about 30 years, from the time of manufacturing. The dielectrics between two conductors of a cable must be able to withstand electrical stresses from high-voltage input. This condition should be verified throughout the lifetime of the cable system. Several techniques, such as VLF-tan${\delta}$, partial discharge, and insulation resistance are used in order to determine the operating conditions of cables. In this paper, we present our work on insulation resistance to diagnose cables in operation at the Western Power station in Taean, Chungcheong Namdo Province, South Korea. As a result we have found cables the life time of which is 38 years.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.36-43
• /
• 1997

FECAPS(ferroelectric capacitors) have been fabricated by RF magnetron sputtering deposition of 3000$\AA$ PZT thin films on the Pt/Ti/$SiO_2$/Si substrates and post-annealing with the temperature of $550^{\circ}C$~$650^{\circ}C$ for 10 sec~50 sec in a RTA system. The electrical characteristics of the fabricated capacitors showed the highest dielectric constant and remanent polarization[${\varepsilon_r(1kHz)$=690, $2P_r$(-5V~5V sweep)=22$\mu$C/$ \textrm{cm}^2$] in the samples annealed at $650^{\circ}C$ for 30 sec, while the lowest tangent loss and leakage current [$tan\delta(\ge10kHz)\le0.02, \; J_i(5V)=3\mu\textrm{A}/\textrm{cm}^2$]in the samples annealed at $600^{\circ}C$ for 30 sec.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.51-60
• /
• 2004

The cure, viscoelastic and mechanical characteristics of organoclay filled NR/BR blends were studied and compared with the properties of carbon black and silica filled NR/BR blends. The nanocomposites with extensive exfoliation state can be fabricated by a solution mixing method. In the composites, the amount of filler content was fixed to 10 phr. Degree of intercalation and exfoliation was characterized by X-ray diffraction (XRD). XRD results indicated exfoliation of the silicate layers into the rubber matrix. While the degree or intercalation and exfoliation is lowered by the conventional mixing method, extensive exfoliation can be obtained by the solution mixing method. It was found that the clay filled NR/BR compound showed better viscoelastic (tan ${\delta}$) and mechanical properties than the carbon black or silica filled NR/BR compounds.

• Korean Journal of Materials Research
• /
• v.6 no.8
• /
• pp.825-832
• /
• 1996

적외선 센서의 재료로 활용되고 있는 PLT박막 (두께:8000$\AA$-9000$\AA$)을 Pt/Ti/SiO2/Si와 Pt/M\ulcorner의 하부 구조상에 50$0^{\circ}C$, 55$0^{\circ}C$ 및 $600^{\circ}C$에서 스퍼터링 증착하여 결정성 및 전기적 특성을 조사하였다. $600^{\circ}C$로 in-situ 성장된 PLT박막은 Si기판을 이용한 경우 randomly oriented perovskite 결정구조를 나타내었으며, Pt/MgO 구조위에서는 c-축(00ι)방향으로 배향 성장되었다. $600^{\circ}C$에서 in-situ 성장된 PLT박막의 비유전상수($\varepsilon$r)와 유전정접(tan $\delta$)을 10kHz-100kHz의 주파수에서 측정한 결과 Pt/Ti/SiO2/Si 구조상에 증착된 박막은$\varepsilon$r=90과 tan $\delta$=0.02의 값을 Pt/MgO 구조상에 증착된 박막은 $\varepsilon$e=35와 tan$\delta$=0.01의 값을 나타내었다. 잔류분극량(2Pr)과 초전계수(${\gamma}$)는 상온부근에서 Si 기판을 이용한 경우 각각 0.6$\mu$C/$\textrm{cm}^2$.。C과 0.5x10-8C/$\textrm{cm}^2$.。C정도로 매우 작게 나타났으나 PLT/Pt/MgO 구조에서는 2Pr=5$\mu$C/$\textrm{cm}^2$, r=4x10-8C/$\textrm{cm}^2$.。C로 비교적 양호한 초전박막의 전기적 특성을 나타내었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.6
• /
• pp.251-255
• /
• 2007

We made $(1-x)BCB-xBNT(BaNd_2Ti_4O_{12})$ (x=20, 30, 40, 50 vol%) composite thick film with a high dielectric constant and low loss by the hand casting method. Dielectric constant and dielectric loss of prepared thick film are measured at 1MHz and curing behavior of the film are observed through thermal analysis such as DSC. We investigated the effect of contents of BNT filler and curing behavior of film on dielectric properties of BCB-BNT composite. Dielectric constant increased with increasing BNT filler from 20 to 50 vol% and dielectric loss ($tan{\delta}$) decreased with increasing BNT filler. Dielectric constant and loss ($tan{\delta}$) of composite material was not nearly dependent on the curing behavior. But as a result of TCC (Temperature Characteristics of Coefficient) decreased with increasing the curing temperature, we confirmed that the curing of these composite system is most stable above $250^{\circ}C$.

• Journal of the Korean Chemical Society
• /
• v.53 no.1
• /
• pp.42-50
• /
• 2009

The dielectric-spectroscopic and ac conductivity studies firstly carried out on layered manganese doped Sodium Lithium Trititanates ($Na_{1.9}Li_{0.1}Ti_3O_7$). The dependence of loss tangent (Tan$\delta$), relative permittivity ($\varepsilon_r$) and ac conductivity ($\sigma_{ac}$) in temperature range 373-723K and frequency range 100Hz-1MHz studied on doped derivatives. Various conduction mechanisms are involved during temperature range of study like electronic hopping conduction in lowest temperature region, for MSLT-1 and MSLT-2. The hindered interlayer ionic conduction exists with electronic hopping conduction for MSLT-3. The associated interlayer ionic conduction exists in mid temperature region for all doped derivatives. In highest temperature region modified interlayer ionic conduction along with the polaronic conduction, exist for MSLT-1, MSLT-2, and only modified interlayer ionic conduction for MSLT-3. The loss tangent (Tan$\delta$) in manganese-doped derivatives of layered $Na_{1.9}Li_{0.1}Ti_3O_7$ ceramic may be due to contribution of electric conduction, dipole orientation, and space charge polarization. The corresponding increase in the values of relative permittivity may be due to increase in number of dipoles in the interlayer space while the corresponding decrease in the values of relative permittivity may be due to the increase in the leakage current due to the higher doping.

• Composites Research
• /
• v.30 no.6
• /
• pp.422-428
• /
• 2017

The moisture absorption behavior, tensile properties, and thermal analysis properties of MWCNT embedded nanocomposites exposed to temperature and moisture were evaluated. The contents of MWCNT were 0 wt%, 1 wt%, and 2 wt%, respectively. The specimens were exposed to immersed conditions at $25^{\circ}C$ and $75^{\circ}C$ for up to 600 hours. According to the results, the apparent moisture content increased as the exposure time increased, but the difference between the maximum moisture content and the moisture content at 600 hours was almost constant. The tensile modulus decreased with increasing exposure time and the degree of decrease was increased significantly as the MWCNT content and exposure temperature increased. The tensile strength decreased with longer exposure time without MWCNT, but increased with MWCNT due to the reinforcing effect of MWCNT. The storage modulus, glass transition temperature, tan d peak magnitude were low as the exposure time increased, but tan d curves with two peaks appeared when exposed to high exposure temperature for more than 300 hours.