• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.95-96
• /
• 2010

This paper proposes photovoltaic thermal hybrid module to get the electrical and Thermal performance of building integrated photovoltaic(BIPV) system. BIPV system is decreased the system efficiency because output of PV is decreased by the thermal rising on generating. In order to improve the efficiency of BIPV module, water cooling system is applied and generated thermal is used the warm water system. Water cooling system uses the flux control algorithm considering water temperature and power loss. Electrical and thermal performance of proposed photovoltaic thermal hybrid module is confirmed through the actual experiment and herby proved the valid of this paper.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.130-136
• /
• 2014

This paper reviews the research on silicon based phased array system operating from microwave to millimeter wave frequencies. First, the design of phase shifter using CMOS technology is presented. The passive phase shifter is applied to the transmit/receive module from one to 16 channel in a single chip. The 35 GHz 4-element T/R module consumes less than 200 mW both transmit and receive modes. The architecture can extend to 16-channel operating at 44 GHz, thereby improving transmit power and linearity. The Ku-band 2-antenna 4-element receiver was developed using active phase shifter based on vector sum method. It is important to minimize coupling between beams because the chip contains four independent beams. The method of coupling is presented and verified.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1467-1474
• /
• 2010

A tile type active T/R(Transmit/Receive) module for X-band active array radar is demonstrated in this paper. Proposed tile type structure based on fuzz button solderless vertical interconnection shows wide band characteristic of about 30 % bandwidth in X-band with insertion loss of below 0.6 dB and input and output VSWR of less than 1.7. Moreover, the mismatching generally appeared in the vertical interconnection which shown wide band characteristic can also be minimized and, therefore, good gain flatness can be achieved.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.6
• /
• pp.703-709
• /
• 2019

This paper proposes a monitoring and remote control system, an essential part of In Vehicle Infotainment (IVI) and Human Vehicle Interface (HVI) to provide safety and convenience to a driver. The system utilizes Bluetooth for a short range communication and utilizes WCDMA for a long range communication to enhance efficiency. In this paper, an integrated controller, which integrates a CAN communication module, a Bluetooth communication module, a WCDMA communication module, is designed to control a car. Also, a remote server for managing data is designed to provide real-time monitoring and remote control for a user via smart devices. Experiment results show that all the proposed remote control, driving log, real-time monitoring, and diagnostics functions are working properly. With the proposed system, a driver can drive safely by monitoring and inspecting a car before driving via smart devices, and control conveniently by controlling a car remotely.

• Bulletin of the Korean Mathematical Society
• /
• v.59 no.4
• /
• pp.917-928
• /
• 2022

Let R be a commutative Noetherian ring and I an ideal of R. In this paper, we study colocalization of generalized local homology modules. We intend to establish a dual case of local-global principle for the finiteness of generalized local cohomology modules. Let M be a finitely generated R-module and N a representable R-module. We introduce the notions of the representation dimension r^I(M, N) and artinianness dimension a^I(M, N) of M, N with respect to I by r^I(M, N) = inf{i ∈ ℕ₀ : H^I_i(M, N) is not representable} and a^I(M, N) = inf{i ∈ ℕ₀ : H^I_i(M, N) is not artinian} and we show that a^I(M, N) = r^I(M, N) = inf{r^IR_𝔭 (M_𝔭,𝔭N) : 𝔭 ∈ Spec(R)} ≥ inf{a^IR_𝔭 (M_𝔭,𝔭N) : 𝔭 ∈ Spec(R)}. Also, in the case where R is semi-local and N a semi discrete linearly compact R-module such that N/∩_t>0I^tN is artinian we prove that inf{i : H^I_i(M, N) is not minimax}=inf{r^IR_𝔭 (M_𝔭,𝔭N) : 𝔭 ∈ Spec(R)＼Max(R)}.

• KIEAE Journal
• /
• v.7 no.6
• /
• pp.17-22
• /
• 2007

The integration of PV modules into building facades or roof could raise their temperature that results in the reduction of PV system's electrical power generation. Hot air can be extracted from the space between PV modules and building envelope, and used for heating in buildings. The extraction of hot air from the space will enhance the performance of BIPV systems. The solar collector utilizing these two aspects is called PV/T(photovoltaic/thermal) solar collector. This paper compares the experimental performance of two different types of air type PV/T collector units: the base case of a collector unit with 10cm gap for forced ventilation and the other unit with copper pin attached to PV module to enhance its thermal performance. The experimental results shows that the base case unit had the overall efficiency of 41.9% and the improved unit with copper pin attached to PV module had 50.1% efficiency. For these air type PV/T units, the forced ventilation of the air space improved the electrical performance as well as the thermal performance.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.300-302
• /
• 2021

Usage of a face mask has become mandatory in many countries after the COVID-19. This paper described to develop a IoT based smart mask system for monitoring face mask. The system developed in this paper has two main units, a sensor module, and a smartphone application. The sensor module consists of four components: temperature and humidity sensor, a heart rate sensor, and a BLE chip. This components work as a unit to collect data and stream them through an I2C port over BLE to a connected mobile device. The smartphone application is an Android application developed for smart phones. It enables the Android device to communicate with the sensor to receive sensor data, process, store and display results.

• Proceedings of the Korea Contents Association Conference
• /
• 2006.11a
• /
• pp.575-579
• /
• 2006

Intelligent Tutoring System is composed of tutoring module, student module and expert module. Among the modules, interface module is the most closely related to students and shares the biggest part of a learning system. Interface module is important for students both in e-learning system but also in intelligent tutoring system. But research on the improvement of interface hasn't been actively done. It studied the interface improvement that has very close relation to e-Learning students. It studied the main components of the existing interface and designed multimedia interface to correct the problems of previous researches. It also suggested the method to relate it to the intelligent tutoring system.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.131-136
• /
• 2002

A design system of dies for hot extrusion of structural shapes such as Z's, L's, T's, U's and H's from aluminium alloys was developed in this study. The developed design system of dies is based of estimated die design rule system. The design rules for die design are obtained from the handbooks, plasticity theories and relevant references. The environment of the system is AutoCAD and AutoLISP, the graphic programming language was used for the configuration of the system. This system includes five major modules such as section shape design module, die opening number module, die opening layout module, die correction module and die bearing design module that are used to determine design variables. This system would be used to design of dies for hot extrusion from aluminum alloys and widely used in manufacturing course.

• The Journal of Korea Robotics Society
• /
• v.11 no.3
• /
• pp.163-171
• /
• 2016

A modular manipulator in serial-chain structure usually consists of a series of modularized revolute joint and link modules. The geometric shapes of these modules affect the number of possible configurations of modular manipulator after assembly. Therefore, it is important to design the geometry of the joint and link modules that allow various configurations of the manipulators with minimal set of modules. In this paper, a new 1-DoF(degree of freedom) joint module and simple link modules are designed based on a methodology of joint configurations using a series of Rotational(type-R) and Twist(type-T) joints. Two of the joint modules can be directly connected so that two types of 2-DoFs joints could be assembled without a link module between them. The proposed geometries of joint and link modules expand the possible configurations of assembled modular manipulators compared to existing ones. Modular manipulator system of this research can be a cornerstone of user-centered markets with various solution but low-cost, compared to conventional manipulators of fixed-configurations determined by the provider.