• KIEE International Transactions on Electrophysics and Applications
• /
• v.5C no.2
• /
• pp.49-53
• /
• 2005

The current drive in a MOSFET is limited by the intrinsic channel resistance. All other parasitic elements in a device structure perform significant functions leading to degradation in the device performance. These other resistances must be less than 10$\%$-20$\%$ of the channel resistance. To meet the necessary requirements, the methodology of separation and quantification of those resistances should be investigated. In this paper, we developed an extraction method for the resistances using calibrated TCAD simulation. The resistance of the extension region is also partially determined by the formation of a surface accumulation region that gathers below the gate in the tail region of the extension profile. This resistance is strongly affected by the abruptness of the extension profile because the steeper the profile is, the shorter this accumulation region will be.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1683-1684
• /
• 2008

For direct detection of microbes in air, samples have to be collected but environmental particles such as dust are also trapped in such samples. Therefore the isolation of target bacteria from non-biological materials of similar size is of great importance in the identification of such organisms. Dielectrophoresis is an emerging technique that can rapidly separate cells in microfluidics. In this paper we proposed a new method for the separation of airborne microbes using condensation and dielectrophoresis. This system could be used as a continuous flow through separation system for various particles and utilized as a pretreatment technique for microbe detection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.144-150
• /
• 2008

This research aims to develop parts for advanced fuel/oil filtering re-circulation applicable to this kind of regulation proof engines. These parts can playa role of converting traditional air emission type crankcase into recovery type crankcase so that the engine can deal with environmental regulations, which do not allow minimal amount of toxic gas discharge. For the experiment, test method and specially made testing equipment are prepared. The results showed that oil separation efficiency of the cone type CCV(Crank Case Ventilation) system was higher than one of cylinder type both in bench test and in engine.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.4 no.1
• /
• pp.27-35
• /
• 1986

Following results about Y,M,C Mask are obtained by the Indirect-Screen Color Separation Method. We make use of experimental system which are in use for the student education. In the Camera-Back Method of reflection copy, the results are summerized as follows.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.5 no.1
• /
• pp.25-32
• /
• 1987

Following results about Y, M, C mask are obtained by the Indirect-Screen Color Separation Method. We mark use of experimental system which are in use for the student education. In the All-Projection Method of transparency Copy, the results are summerized as follows; (omitted)

• Journal of Mechanical Science and Technology
• /
• v.17 no.6
• /
• pp.825-835
• /
• 2003

Previous studies have demonstrated the importance of joint angle errors mainly due to skin artifact and measurement errors during gait analysis. Joint angle errors lead to unreliable kinematics and kinetic analyses in the investigation of human motion. The purpose of this paper is to present the Joint Averaging Coordinate System (JACS) method for human gait analysis. The JACS method is based on the concept of statistical data reduction of anatomically referenced marker data. Since markers are not attached to rigid bodies, different marker combinations lead to slightly different predictions of joint angles. These different combinations can be averaged in order to provide a "best" estimate of joint angle. Results of a gait analysis are presented using clinically meaningful terminology to provide better communication with clinical personal. In order to verify the developed JACS method, a simple three-dimensional knee joint contact model was developed, employing an absolute coordinate system without using any kinematics constraint in which thigh and shank segments can be derived independently. In the experimental data recovery, the separation and penetration distance of the knee joint is supposed to be zero during one gait cycle if there are no errors in the experimental data. Using the JACS method, the separation and penetration error was reduced compared to well-developed existing methods such as ACRS and Spoor & Veldpaus method. The separation and penetration distance ranged up to 15 mm and 12 mm using the Spoor & Veldpaus and ACRS method, respectively, compared to 9 mm using JACS method. Statistical methods like the JACS can be applied in conjunction with existing techniques that reduce systematic errors in marker location, leading to an improved assessment of human gait.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.5
• /
• pp.598-606
• /
• 2013

After the missile is launched, the umbilical connector should be separated from it without any physical interference. The umbilical separation device, for this purpose, was developed by means of new concept. Using the investigation of various methods to separate the umbilical connector, a suitable method was selected and a corresponding device was designed and manufactured. To ensure the performance of the developed device, numerical analysis and performance test were conducted and correction was followed. The umbilical separation device was applied to real system operation test and its operation performance was tested. In consequence, several problems were founded, however, good results were generally obtained.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.597-601
• /
• 2001

Waste plastics amount is more than 3.5 million tons and 30% of industrial waste in 1998, Korea but recycling rate of industrial waste plastics is quite low because the material separation technology from the mixed waste plastic powders is not commercially available so far. This study covers the triboelectrostatic separation of polyvinylchloride (PVC) materials collection chambers and controllers. PVC and PET powders can be imparted negative and positive surface charges, respectively, due to the difference of triboelectric charging series between particles and particles in the fluidized bed tribocharger, and can be separated by passing them through an external electric field. The extract content and yield of PVC separation from the mixed PVC and PET plastic powders are 90.0% and 98.2%, respectively. The electrostatic separation system using the fluidized bed tribocharger shows the potential to be an effective method for removing PVC materials from other mixed plastics.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.10
• /
• pp.1101-1108
• /
• 2015

In this paper, to provide a method and system for providing a network separation virtual machine environment. How to provide this virtual machine environment include phase generating necessary virtual resource requirement for the perform of virtual function and transfer to network changing protocol about request of registration virtual resource. For this reason, Registration procedure is to use a virtual machine for a virtual computing resource allocation and separation combined network any time, it became possible between servers and clients, or mobile phone. At any time, it is possible to process the work in the same environment as in a computer to access the Internet.

• Journal of Internet of Things and Convergence
• /
• v.6 no.2
• /
• pp.37-43
• /
• 2020

The paper proposed the method of calculating the latest approach angle that can reliably recognize multiple laser images even with the change in separation distance between screen and laser launch device. This method recognizes the angle of the laser pattern angle by using the distance of the laser pattern angle, and the angle extraction of the laser detects the laser image from the acquired image using the labeling algorithm, and performs the huff conversion to extract the angle of the straight line. The distance of the reference angle and angle of the laser image extracted using Euclidean distance among similarity scales is calculated, and the furnace is recognized using the calculated distance result value. Experiments with changing the separation distance to "200 cm to 400 cm" showed 100% recognition of individual strands at all separation distances. The experiment confirmed the reliability of the proposed method.