• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.302-304
• /
• 2004

Nuclear fuel elements containing dry recycling nuclear fuel pellets for the irradiation test in a reactor were remotely fabricated from spent PWR fuel materials in a hot cell. End closure welding as well as seal tube welding for thermal sensor of the elements was performed by Nd:YAG laser. The soundness of the end closure welds and seal tube welds for the elements were evaluated by a precise X-ray inspection system composed of a micro-focus X-ray generator with an image intensifier and a real time camera system. Then, helium leak test was performed for the elements. The soundness of the welds of the fuel elements was confirmed by the X-ray inspection and helium leak test. The irradiation test for the fuel elements were successfully completed at the HANARO research reactor.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.4
• /
• pp.11-17
• /
• 1998

Reducing the effluent discharge from a paper mill is urgently needed due to tightening environmental regulations and economic reasons. For a paper mill to respond to system closure it is required to adopt the best practical retention system that enables the mill to improve fines retention and drainage. In this study, effects of various retention agents on fines retention, drainage and formation were examined using linerboard stock in the laboratory. Among the retention aids tested, high molecular weight cationic polyacrylamides showed good efficiency both in retention and drainage. On the other hand, high charge density, low molecular weight polymeric retention aids showed little improvement both in retention and drainage. The best retention system selected from the laboratory experiment was applied on a paper machine producing linerboard to evaluate its effect on papermaking system closure.

• Nuclear Engineering and Technology
• /
• v.31 no.1
• /
• pp.68-79
• /
• 1999

The YGN Units 3&4 plant conditions during shutdown operation were reviewed to identify the possible event scenarios following the loss of shutdown cooling (SDC) event. For the five cases of typical reactor coolant system (RCS) configurations under the worst event sequence, such as unavailable secondary cooling and no RCS inventory makeup, the thermal hydraulic analyses were performed using the RELAP5/MOD3.2 code to investigate the plant behavior following the event. The thermal hydraulic analyses include the estimation of time to boil, time to core uncovery, and time to core heat up to determine the containment closure time to prevent the uncontrolled release of fission products to atmosphere. The result indicates that the containment closure is recommended to be achieved within 42 minutes after the loss of SDC for the steam generator (SG) inlet plenum manway open case or the large cold leg open case under the worst event sequence. The containment closure time is significantly dependent on the elevation and size of the opening and the SG secondary water level condition. It is also found that the containment closure needs to be initiated before the boiling time to ensure the survivability of the workers in the containment. These results will provide useful information to operators to cope with the loss of SDC event.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.2
• /
• pp.223-229
• /
• 2008

In this paper. we propose the real-time vision system which judges drowsiness driving based on levels of drivers' fatigue. The proposed system is to prevent traffic accidents by warning the drowsiness and carelessness using face-image analysis and fuzzy logic algorithm. We find the face position and eye areas by using fuzzy skin filter and virtual face model in order to develop the real-time face detection algorithm, and we measure the eye blinking frequency and eye closure duration by using their informations. And then we propose the method for estimating the levels of drivel's fatigue based on measured data by using the fuzzy logic and for deciding whether drowsiness driving is or not. Finally, we show the effectiveness and feasibility of the proposed method through some experiments.

• Journal of Soil and Groundwater Environment
• /
• v.22 no.4
• /
• pp.33-48
• /
• 2017

An optimum disposal plan of disused sealed radioactive sources (DSRSs) should be established to ensure long-term disposal safety at the low- and intermediate-level radioactive waste (LILW) disposal facility in Gyeongju. In this study, an optimum disposal system was suggested and preliminary post-closure safety assessment was performed. The DSRSs disposal system was composed of a rock cavern and near surface disposal facilities at the Gyeongju LILW disposal facility. The assessment was conducted using GoldSim program, and probabilistic assessment and sensitivity analysis were implemented to evaluate the uncertainties in the input parameters of natural barriers. Deterministic and probabilistic calculations indicated that the maximum dose was below the regulatory limits ($0.1mSvyr^{-1}$ for the normal scenario, $1mSvyr^{-1}$ for the well scenario). It was concluded that the DSRSs disposal system would maintain environmental safety over a long-time. Moreover, the partition coefficient of Np in host rock, Darcy velocity in host rock, and density of the host rock were the most sensitive parameters in predicting exposure dose in the safety assessment.

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.399-407
• /
• 1998

An investigation into the modal interaction of an autoparameteric systemunder broad-band random excitation is made. The specific system examined is a spring-pendulum system with internal resonance, which is known to be a good model for a variety of engineering systems, including ship motions with nonlinear coupling between pitching and rolling motions. By means of the Gaussian closure method the dynamic moment equations explaining the random responses of the system are reduced to a system of autonomous ordinanary differential equations of the first and second moments. In view of equilibrium solutions of this system and their stability we examine the system responses. The stabilizing effect of system damping is also examined.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.843-849
• /
• 2009

The reliable operation of a swing check valve in the main feed water system of a power plant is most essential for successful shout-down process. A failure to close the valve at proper time often leads to the instability of the main feed water system, or even to an emergency stop of the power plant. In reality it is a very difficult task to monitor the behavior of a swing check valve. Furthermore it is impossible to see the motion of the valve. In this work two measurements were carried out simultaneously to determine the precise valve closure time. The dynamic pressure measurements were made at the inlet and outlet regions of the swing check valve. The transient vibration of the valve housing in the direction of water flow was also measured, which enabled the measurement of the transient vibration of the valve housing near valve closure. By comparing the results produced from these measurements the precise valve closure time could be determined. By carrying out order tracking technique using the dynamic pressure signals and pump rpm signal, the complicated dynamic problems inside the main feed water system can be more easily dealt with. This measurement scheme might be implemented in a power plant on a real-time basis without much difficulty. If this could be implemented, valuable information essential for shut-down operations can readily be passed on to the main control room. The feasibility of this implementation was demonstrated by this experimental work.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.1
• /
• pp.218-226
• /
• 2017

In this paper, optical transport network in real time monitoring system using smart phone. The existing housing using monitoring was a smart phone of optical transport network access switch about an event with new installation of cognitive system in real time. This paper can this problem to be solved of the invention in real time maintenance using smart phone application and optical cable closure switch. If you want to find optical cable closure fault location, this smart phone web is very useful. Cable tie is isolation of fiber spare board from fiber switch tie occur push message. Housing and access, and an external failures otdr the measurement of the global positioning to be able to easily using the This paper can find event of optical cable closure unauthorized work and fault using smart phone OTDR function. the optical cable fault time reduction and network transport quality by managing real time optical cable section by using the smart phone can be maintained efficiently.

• Archives of Plastic Surgery
• /
• v.38 no.1
• /
• pp.121-126
• /
• 2011

Purpose: Vaccum-assisted closure (VAC) has rapidly evolved into a widely accepted treatment of contaminated wounds, envenomations, infiltrations, and wound complications. This results in a sealed, moist environment where tissue is given the opportunity to survive as edema is removed and perfusion is increased. Many plastic surgeons now place a VAC device directly over the fasciotomy site at the time of the initial procedure. Large amounts of the fluid are withdrawn, and fasciotomies can be closed primarily sooner. This study was designed to observe the effect of VAC in preventing complications in snake bitten hands. Methods: In our study of three cases of snake bite, three of them underwent the VAC treatment & fasciotomy of the wound in the hand. This cases, the posterior compartment of the hand was bitten for a few days, releasing incisions were made of the posterior hand and 125 mmHg of continuous vacuum was applied to fasciomy incision site and the biting wound. The dressings were changed three times per week. Results: Our study examining the effects of applied vacuum in preventing snake bite wounds showed that the incidence of tissue necrosis and compartment syndrome was significantly lower for vacuum-treated wounds than for conservative wounds. Serum myoglobin, CK-MB, and CPK levels measured after fasciotomy incision were significantly decreased. We obtained satisfactory results from early dorsal fasciotomy, drainage of the edema with the VAC system, and then primary closure. The postoperative course was uneventful. Conclusion: Envenomation is a term implying that sufficient venom has been introduced into the body to cause either local signs at the site of the bite and/or systemic signs. Use of the vacuum-assisted closure device in snake bite can result in a decreased rate of tissue necrosis, lymphatic fluid collection, hemolytic fluid collection, and edema. Early fasciotomy of the dorsal hand and VAC apply is the alternative treatment of the snake bite.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.5
• /
• pp.404-414
• /
• 2000

This paper addresses the development of a 3-fingered humanoid robot hand system and a real-time grasp synthesis of multifingered robot hands to find grasp configurations which satisfy the force closure condition of arbitrary shaped objects. We propose a fast and efficient grasp synthesis algorithm for planar polygonal objects, which yields the contact locations on a given polygonal object to obtain a force closure grasp by the multifingered robot hand. For an optimum grasp and real-time computation, we develop the preference and the hibernation process and assign physical constraints of the humanoid hand to the motion of each finger. The preferences consist of each sublayer reflecting the primitive preference similar to the conditional behaviors of humans for given objectives and their arrangements are adjusted by the heuristics inspired from human's grasping behaviors. The proposed method reduces the computational time significantly at the sacrifice of global optimality, and enables the grasp posture to be changable within two-finger and three-finger grasps. The performance of the presented algorithm is evaluated via simulation studies to obtain the force-closure grasps of polygonal objects with fingertip grasps. The architecture suggested is verified through experimental implementation to our robot hand system by solving the 2- or 3-finger grasp synthesis.