• YAKHAK HOEJI
• /
• v.49 no.2
• /
• pp.162-167
• /
• 2005

Synthetic method for the selective N-monoalkylation of anilines using alkyl halides and triethylamine under room temperature was described. The corresponding N-alkyl anilines were obtained in good yields with minor quantities of dialkylated products. Anilines 2a-m and 3a-m were identified using NMR and IR. A series of 2a-m and 3a-m has been synthesized from aniline, toluidines, ethylanilines, aminoacetophenones, phenetidines. Formation of anilines was undertaken with dropping of alkylhalides at room temperature in methanol (or ethanol) for 3 hours~5 days. Selectivity on the monoalkylation was relatively high. Synthetic ratio of monoalkylated and dialkylated product was 94 : 6 in case of maximum monoalkylation.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.1
• /
• pp.79-89
• /
• 2019

The field measurement and laboratory experiment were conducted to investigate the effect of reducing the surface temperature of the functional aspect of the heat island phenomenon of the permeable block which is made the recycled synthetic resin rather than the existing concrete permeable block. Field measurement was taken for 3 days in consideration of dry condition and wet condition and laboratory experiment was divided into dry condition, rainfall simulating condition, and wetting condition. The variations of temperature and the evaporation rate of water moisture content after experiment were confirmed. As a result of field measurement, it is confirmed that the surface temperature decreases due to the difference in albedo of the pore block surface rather than the cooling effect due to the latent heat of vaporization. The evaporation of moisture in a dry state where drought persisted or a certain level of moisture was not maintained in the surface layer. As a result of laboratory experiment, resin permeable block gives higher surface temperature when it is dry condition than concrete permeable block, but the evaporation of water in the pore is kept constant by capillary force in rainfall simulation condition, and higher temperature reduction rate. As a result of measuring the evaporation rate after laboratory experiment, it is confirmed that the effect of reducing temperature is increased as the evaporation rate of water is higher. Based on these results, correlation formula for evaporation rate and temperature reduction rate is derived.

• Journal of Magnetics
• /
• v.11 no.1
• /
• pp.5-7
• /
• 2006

The magnetotransport properties at room temperature of the 250-nm-thick MnAs(-1100) film grown on GaAs(001) substrate by molecular beam epitaxy was investigated. The results measured with various magnetic field directions were reported. They show the negative magnetoresistive effect for all field directions. The difference in the magnetoresistance curves for different field directions is in agreement with the magnetic anisotropy of the film.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.2
• /
• pp.243-248
• /
• 2004

As diverse synthetic precursors of cyclic adenosine diphosphate ribose (cADPR), several adenosine derivatives in which azido or amino group is introduced at 2'- or 3'-position of the sugar moiety of adenosine were prepared from readily available adenosine via conventional protocols. These synthetic sequence employs very efficient reactions conditions that proceed at or below ambient temperature with actual yields of >80% for each individual step.

• Journal of Korean Society on Water Environment
• /
• v.22 no.4
• /
• pp.658-665
• /
• 2006

The removal characteristics of silver ion from waste photographic solution have been investigated by recovering silver electrochemically. Cyclic voltammetry for synthetic and actual wastewater which containing silver ion was investigated to understand its electrochemical behavior. For both synthetic and actual wastewater, the recovery of silver according to the electrowinning time was observed to be increased as the applied potential was raised. In addition, the applicable potential for the electrowinning of silver was found to be lower for synthetic wastewater compared with actual wastewater. As the temperature was increased, more silver was recovered for both wastewater, which indicated the electrowinning reaction was endothermic. The electrowinned silver was refined electrochemically to increase its purity and the variation of the purity of silver was examined according to the electrorefining potential.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.50 no.1
• /
• pp.49-57
• /
• 2008

This study evaluated the flexural properties and fire resistance of polyolefm based structural synthetic fiber reinforced concrete. The effects of differing fiber length, dimension and fiber volume fraction were studied. Flexural and fire resistance test were conducted in accordance with the JCI SF-4 and RABT time heating temperature curve, respectively. The Flexural test results indicated that the polyolefln based structural fiber reinforcement showed an ability to increase the flexural toughness and good fire resistance significantly(as compared to steel fiber reinforcement).

• Textile Coloration and Finishing
• /
• v.18 no.6 s.91
• /
• pp.63-68
• /
• 2006

In synthetic/spandex blends fibers, contents of the synthetic fiber by percentage is higher than those of spandex. Thus, the dyeing process of the blends fiber is mainly focused on the synthetic fiber, but not the spandex. In this study, we used several series of vat dyes for dyeing the nylon/spandex blend fabrics and their dyeing properties(fk value) were investigated at various reduction agents, temperatures, pH which have the potential for deep shade dyeing effects. The formamidinesulfinic acid were found to be effective to increase the fk values of the blend fiber compared to sodium hydrosulfite and Rongalit C. Higher temperature($100^{\circ}C$) and lower pH(pH 4) were observed as suitable conditions for maximum fk values.

• Resources Recycling
• /
• v.9 no.1
• /
• pp.27-35
• /
• 2000

Characteristics of pyrolytic gasification were examined for the waste tire and 7 types of waste synthetic resin, using a bench scale experimental facility. the product gas temperature of waste tires was $150~300^{\circ}C$ and the temperature profile in the combustion zone of the lower reactor part tended to be clearly distinguished from that in the gasification zone of the upper part. However, in the case of waste synthetic resins, there were no clear distinction and temperature fluctuation was severe, depending on the reaction time. Product gas quantity, which depends on that of supplied (1st) air, was found to be 105~135% of the 1st air amount at the steady state. The concentration of noncombustible components in product gas was 80~90 vol.% and the high heating value of the product gas calculated from gas compositions was 1,500~3,000 kcal/N㎥ for waste tire, and 300~2,900 kcal/N㎥ for waste synthetic resins, respectively. Heating value of product gas and combustible gas concentration were increased in proportion to 1st air amount when 1st air amount is below $0.35N\textrm{m}^3$/min.

• Journal of the Korean Ceramic Society
• /
• v.30 no.4
• /
• pp.325-331
• /
• 1993

Aqueous solutions of metallic salts, ZrO(NO3)2.2H2O and Y(NO3)3.5H2O were used as raw materials to synthesize crystalline submicron spherical powders of Zr0.94Y0.06O1.97 with tetragonal crystal phase. Each aqueous solution was mixed on the magnetic stirrer to homogenize for 12 hours. The concentration of the mixed solutionwas changed from 0.01mol/$\ell$ to 0.1mol/$\ell$ calculated as the concentration of Zr0.94Y0.06O1.97. Ultrafine droplets of starting mixed solution were sprayed by the ultrasonic vibrator and carried into the furnace kept at 55$0^{\circ}C$, $650^{\circ}C$, 75$0^{\circ}C$ and 85$0^{\circ}C$ using carrier gas of air (10$\ell$/min) and pyrolysed to form Y-TZP fine powders. The results of this exeriment were as follows. 1) Synthesized powders were nonagglomerated and spherical type. 2) Particle size distribution was narrow between 0.1${\mu}{\textrm}{m}$ and 1${\mu}{\textrm}{m}$. 3) Forming reaction Y-TZP was finished above synthetic temperature 75$0^{\circ}C$. 4) As the synthetic temperature rised from 55$0^{\circ}C$ to 85$0^{\circ}C$, the mean particle size decreased from 0.35${\mu}{\textrm}{m}$ to 0.22${\mu}{\textrm}{m}$ in the concentration of starting solution with 0.02mol/$\ell$. 5) At 75$0^{\circ}C$ of synthetic temperature, the concentration changes of starting solution from 0.01mol/$\ell$ to 0.1mol/$\ell$ increased the mean particle size from 0.24${\mu}{\textrm}{m}$ to 0.38${\mu}{\textrm}{m}$. 6) Chemical compositions of each synthesized particle were homogeneous nearly.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.217-221
• /
• 2001

We made magnetite which was prepared with mixed liquids of Fe$\^$2+/and Fe$\^$3+/ added to the 3N-NaOH by coprecipitation reaction. Ahead of making magnetite, we investigated variation of physical properties for changing Fe$\^$2+/ : Fe$\^$3+/. Through the variation of the process temperature, we examined physical properties of magnetite. Also, to examine possibility of magnetic fluids, from magnetite manufactured in this way, we examined the crystal structure by X-ray diffraction pattern. The saturated magnetization $\sigma$$\_$s/, value has 60.8 emu/g, when Fe$\^$2+/ to Fe$\^$3+/ ratio is 0.46 : 0.54 in the synthetic magnetite. Keeping the condition, when the synthetic temperature is kept at 80$\^{C}$ for 30 minutes, we get $\sigma$$\_$s/, value 63.51 emu/g. It shows that $\sigma$$\_$s/, value is bigger as the synthetic temperature is higher.