• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.187-190
• /
• 2004

Transducer for ultrasonic linear motor with the symmetric and anti-symmetric modes was studied. The ultrasonic liner motor consists of two Lngevin type piezoelectric vibrators that cross at right angles with each other in tip. In order to excite symmetric and anti-symmetric mode, the transducer must have a 90 degree phase difference of voltage. Therefore, the tip of transducer moves on an elliptical motion. In this paper, the finite element analysis was used. The ultrasonic motor was fabricated using the simulated result and the driving characteristics were measured.

• International Journal of CAD/CAM
• /
• 제9권1호
• /
• pp.103-109
• /
• 2010

Recently, various conformal geometric methods have been presented for non-rigid surface matching and registration. This work proposes to improve the robustness of conformal geometric methods to the boundaries by incorporating the symmetric information of the input surface. We presented two symmetric conformal mapping methods, which are based on solving Riemann-Cauchy equation and curvature flow respectively. Experimental results on geometric data acquired from real life demonstrate that the symmetric conformal mapping is insensitive to the boundary occlusions. The method outperforms all the others in terms of robustness. The method has the potential to be generalized to high genus surfaces using hyperbolic curvature flow.

• 한국전기전자재료학회논문지
• /
• 제16권8호
• /
• pp.669-675
• /
• 2003

Transducer for ultrasonic linear motor with symmetric and anti- symmetric modes was studied. The ultrasonic linear motor consists of two Langevin type piezoelectric vibrators that cross at right angles with each other in tip. In order to excite symmetric and anti-symmetric modes, the transducer must have a phase shift of 90 degree in space and time. As a result, the tip of transducer moves on an elliptical motion. In this paper, the finite element analysis was used to optimize dimension and displacement of the transducer.

• 한국실내디자인학회논문집
• /
• 제38호
• /
• pp.75-82
• /
• 2003

The symmetry is general geometric design principal in contemporary architecture shape. But, Symmetry sometimes easily causes unreasonable design. In some reason, two of symmetric units in the apartment, one side of unit have very reasonable plan and arrangement but opposite side unit nay not. For example, if the kitchen on right unit had right-handed arrangement, the symmetrical other would have left-handed kitchen arrangement. In addition to this, if each house unit has the same plan but different direction, each unit has different usage or affects the residents' life pattern. Nevertheless, Architects use only one unit plan to design public housing development by using symmetric operator (mirror, proper rotation, inversion center) at their option. This study suggests that using group theory and mathematical matrix rather than designer's discretion can solve this symmetry problem clearly. And, this study analysis the merits and demerits between each symmetrical pair of unit plan shapes by using mathematical point group theory and matrix.

• Journal of Communications and Networks
• /
• 제14권6호
• /
• pp.682-691
• /
• 2012

Key agreement protocol is a fundamental protocol in cryptography whereby two or more participants can agree on a common conference key in order to communicate securely among themselves. In this situation, the participants can securely send and receive messages with each other. An adversary not having access to the conference key will not be able to decrypt the messages. In this paper, we propose a novel identity-based authenticated multi user key agreement protocol employing a symmetric balanced incomplete block design. Our protocol is built on elliptic curve cryptography and takes advantage of a kind of bilinear map called Weil pairing. The protocol presented can provide an identification (ID)-based authentication service and resist different key attacks. Furthermore, our protocol is efficient and needs only two rounds for generating a common conference key. It is worth noting that the communication cost for generating a conference key in our protocol is only O($\sqrt{n}$) and the computation cost is only O($nm^2$), where $n$ implies the number of participants and m denotes the extension degree of the finite field $F_{p^m}$. In addition, in order to resist the different key attack from malicious participants, our protocol can be further extended to provide the fault tolerant property.

• Steel and Composite Structures
• /
• 제32권4호
• /
• pp.423-441
• /
• 2019

This study aims to accurately predict the first ply failure loads of laminated composite hypar shell roofs with different boundary conditions. The geometrically nonlinear finite element method (FEM) is used to analyse different symmetric and anti-symmetric, cross and angle ply shells. The first ply failure loads are obtained through different well-established failure criteria including Puck's criterion along with the serviceability criterion of deflection. The close agreement of the published and present results for different validation problems proves the correctness of the finite element model used in the present study. The effects of edge conditions on first ply failure behavior are discussed critically from practical engineering point of view. Factor of safety values and failure zones are also reported to suggest design and non-destructive monitoring guidelines to practicing engineers. Apart from these, the present study indicates the rank wise relative performances of different shell options. The study establishes that the angle ply laminates in general perform better than the cross ply ones. Among the stacking sequences considered here, three layered symmetric angle ply laminates offer the highest first ply failure load. The probable failure zones on the different shell surfaces, identified in this paper, are the areas where non-destructive health monitoring may be restricted to. The contributions made through this paper are expected to serve as important design aids to engineers engaged in composite hypar shell design and construction.

• 대한전자공학회논문지SD
• /
• 제44권10호
• /
• pp.33-37
• /
• 2007

본 논문에서는 vertical shunt symmetric inductor를 이용하여 CMOS LNA의 설계에 있어서 회로의 면적을 줄이는 설계기술 및 구현에 관한 내용을 제시하고자 한다. 본 연구에 있어서 vertical shunt symmetric inductor는 LNA의 입력단과 출력단을 3GHz로 정합하기 위해서 사용되었다. 이렇게 구현된 보다 면적에 있어서 효율적인 증폭기를 0.18um digital logic공정으로 구현되었다. 본 논문에서는 일반적으로 LNA에서 사용하고 있는 inductor를 이용하는 경우와, vertical shunt symmetric inductor를 이용하여 LNA를 설계하는 경우에 대한 부분을 비교하였고, 최종적으로 면적에 효율적인 회로설계 기술을 제시하고자 한다.

• Journal of information and communication convergence engineering
• /
• 제21권2호
• /
• pp.103-109
• /
• 2023

We investigated the antipodal-symmetric dispersion maps of a dispersion-managed link with a midway optical phase conjugator to compensate for the distorted 960 Gb/s wavelength division multiplexed (WDM) signal caused by these effects. The proposed antipodal-symmetric dispersion map has various shapes depending on the detailed design scheme. We confirmed that the dispersion-managed link designed with the dispersion map of the antipodal-symmetric structure is more advantageous than the conventional uniform dispersion map for compensating WDM channels. It was also confirmed that among the antipodal-symmetric structures, the dispersion map configured with the S-1-profile, in which S is inverted up and down, was more effective for distortion compensation than the dispersion map configured with the S-profile. In particular, we confirmed that the S-1-profile can broaden the optical pulse width intensively at a short transmission distance, more effectively compensating for the distorted WDM channel. Because this structure makes the intensity of the optical pulse relatively weak, it can decrease the nonlinear Kerr effect.

• 대한전자공학회논문지SD
• /
• 제40권9호
• /
• pp.702-713
• /
• 2003

정보통신 및 네트워크의 급격한 발전으로 인하여 정보보호분야의 중요성은 매우 크다. 또한 사용자에 의한 서비스 수요가 증가하면서 개인정보보호에 대한 관심이 증가하였다. 이러한 이유로 대칭형 암호방식보다는 비대칭형 암호방식이 주류를 이루게 되었다. 그러나 비대칭형 암호방식은 대칭형 암호시스템에 비하여 처리속도가 낮아서 적용되는 분야가 한정된다. 그러므로 본 논문에서는 대칭형 암호시스템을 이용하여 비대칭형 암호시스템의 인증기능을 수행할 수 있도록 하는 암호시스템을 설계하였다. 제안된 암호시스템은 블록 암호방식과 스트림 암호방식을 혼용하여 사용하였다. 대칭형/비대칭형 암호시스템은 고정된 키에 의하여 암호/복호를 수행하지만 제안된 암호시스템은 평문의 정보에 의하여 키수열이 변화하도록 함으로써 비도 측면에서 매우 높은 안전성을 가지도록 하였다. 그러므로 비인가자가 키정보를 확보하여도 크랙하기가 매우 어려워진다. 그러므로 제안된 암호시스템은 대칭형 암호시스템의 처리속도와 비대칭 암호시스템의 인증기능을 가지고 있으므로 데이터 인증 또는 중요한 정보의 교환에 매우 유용하게 사용되리라 사료된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.485-491
• /
• 2001

This paper describes the development of simulation program which is able to design cutter profiles and 3-dimensional geometry for rotors in screw compressor. Based on the symmetric rotor profiles developed previously, cutters are designed and 3-dimensional geometries of rotors are generated used by simulation program. Symmetric rotors are manufactured by a universal milling machine, and surface geometries of them are measured by a 3-dimension scanner. It is shown that simulation program developed is useful to design cutter for rotor manufacturing and to generate the 3-dimensional helicoid geometry of rotor in screw compressor.