• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1305-1317
• /
• 2015

Distributed generation systems (DGSs) have been getting more and more attention in terms of renewable energy use and new generation technologies in the past decades. The self-excited induction generator (SEIG) occupies an important role in the area of energy conversion due to its low cost, robustness and simple control. Unlike synchronous generators, the SEIG has to absorb capacitive reactive power from the outer device aiming to stabilize the terminal voltage at load changes. This paper presents a novel static VAR compensator (SVC) called a magnetic energy recovery switch (MERS) to serve as a voltage controller in SEIG powered DGSs. In addition, many small scale SEIGs, instead of a single large one, are applied and devoted to promote the generation efficiency. To begin with, an expandable mathematic model based on a d-q equivalent circuit is created for parallel SEIGs. The control method of the MERS is further improved with the objective of broadening its operating range and restraining current harmonics by parameter optimization. A hybrid control strategy is developed by taking both of the stand-alone and grid-connected modes into consideration. Then simulation and experiments are carried out in the case of single and double SEIG(s) generation. Finally, the measurement results verify that the proposed DGS with SVC-MERS achieves a better stability and higher feasibility. The major advantages of the mentioned variable reactive power supplier, when compared to the STATCOM, include the adoption of a small DC capacitor, line frequency switching, simple control and less loss.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.27-32
• /
• 2015

In this paper, a mushroom typed electromagnetic band gap (EBG) structure to be inserted in the printed circuit board (PCB) inner layer in order to stabilize the PCB power line is proposed for global-navigation satellite service (GNSS). In designing the proposed EBG structure, the target stop-bandwidth was designed from 1.55GHz to 1.81GHz including GNSS and mobile communication-related frequency bandwidth. In this bandwidth, the insertion loss(S21) was observed below about -40dB. From the simulation results, it is expected that the stabilization of power delivery network (PDN) structure in the PCB circuit design should be improved and the effective correspondence to EMI will be helpful.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.193-200
• /
• 2006

This paper suggests a 6-pulse-shift converter structure with PWM current-source inverter based on buck-boost configuration to improve the efficiency and to reduce the switching frequency of inverter for photovoltaic generation system, the device can be operated as interface system between solar module system and power system grid without energy storage cell. The circuit has six current-source buck-boost converter which operate chopper part and kas one full bridge inverter which make a decision the polarity of AC output. Therefore, the proposed PWM power inverter has advantages such as the reduction of witching loss and realization of unity power factor operation. The theoretical backgrounds are discussed and the input-output characteristics for the implemented prototype inverter using TMS320F2812 are verified experimentally in this paper.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.4 s.119
• /
• pp.364-371
• /
• 2007

In this paper, the design and implementation of high-power PIN diode switch modules and high-speed switch driver circuits are presented for Wibro base stations. To prevent isolation degradation due to parasitic inductances of conventional packaged PIN diodes and to improve power handling capabilities of the switch modules, bare diode chips are used and carefully placed in a PCB layout, which makes bonding wire inductances to be absorbed in the impedance of a transmission line. The switch module is designed and implemented to have a maximum performance while using a minimum number of the diodes. It shows an insertion loss of ${\sim}0.84\;dB$ and isolation of 80 dB or more at 2.35 GHz. The switch driver circuit is also fabricated and measured to have a switching speed of ${\sim}200\;nsec$. The power handling capability test demonstrates that the module operates normally even under a digitally modulated 70 W RF signal stress.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.960-964
• /
• 2001

$Bi_{3.99}Ti_{2.97}V_{0.03}O_{12}$ (BTV) thin films with 3 mol% vanadium doping were Prepared on $Pt/Ti/SiO_2/Si$ substrate by sol-gel method. X-ray diffraction analysis indicated that single-phase layered perovskite were obtained and preferred orientation was not observed. Under the annealing temperature at $600^{\circ}C$, the surface morphology of the BTV thin films had fine-rounded particles and then changed plate-like at $650^{\circ}C$ and $700^{\circ}C$. The remanent polarization $(2P_r)$ and coercive field $(2E_c)$ of $700^{\circ}C$ annealed BTV thin film were 25 $\mu$C/cm$^2$ and 116 kV/cm, respectively. In addition, BTV thin film showed little polarization fatigue during $10_9$ switching cycles. These improved ferroelectric properties were attributed to the increased rattling space and reduced oxygen vacancies by substitution $Ti^{4+}$ ion (68 pm) with smaller $V^{5+}$ ion (59 pm). The dielectric constant and loss were measured 130 and 0.03 at 10 kHz, respectively.

• Korean Journal of Optics and Photonics
• /
• v.21 no.5
• /
• pp.181-184
• /
• 2010

A simple technique for a flexibly tunable and switchable dual wavelength-switchable erbium-doped fiber (EDF) laser using fiber Bragg gratings is proposed and demonstrated by using both linear cavity loss controlling and homogeneous gain broadening of the EDF. The oscillating wavelength switching is successfully realized by using the modulation of the acousto-optic modulator driven by the RF signal. The wavelength spacing and lasing wavelength of the proposed wavelength-switchable laser can also be controlled by using the bending-induced tension or compression strain. The proposed tunable dual wavelength-switchable fiber laser has a lot of advantages, such as a high extinction ratio larger than 40dB and a high tunability of ~7.2 nm/$m^{-1}$.

• Journal of Advanced Navigation Technology
• /
• v.18 no.5
• /
• pp.483-489
• /
• 2014

Proposed electronic ballast circuit for harmonic reduction includes adding lossless snubber circuit to DC-DC converter. To get inverter for changing DC-AC, a lamp has been changed to equivalence resistance in the standard lamp voltage and current data, also inverter circuit has been interpreted by being changed to R, L, C equivalence circuit. Using converted equivalent circuit, the most suitable circuit constant which can satisfy the characteristics of fluorescent lamps has been decided on and finally designed. It could not only eliminate distortion waveform from pulsation frequency in inverter direct side current but also reduce considerably pulsation rate and switching loss by making input current of inverter discontinuous. The validity for the results of this study has been verified through the experiment to measure harmonic occurrence after applying a newly-manufactured product of electronic ballast to 40 W line tube style fluorescent lamps.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.6
• /
• pp.578-583
• /
• 2016

In this paper, we propose a multi-mode wireless power transfer (WPT) system with a dual loop structure. The proposed multi-mode WPT system consist of outer loop module which can operate at two different frequency bands including 6.78 MHz magnetic resonance WPT mode and 13.56 MHz near field communication (NFC) mode and inner loop module connected with outer loop which can operate at two different frequency bands including WPC mode and PMA mode based on inductive coupling standards. In order to be able to embed this system into smartphone battery back cover, the electrical designs are optimized and then the size was fixed $45{\times}90{\times}0.35mm3$ (including ferrite sheet) which is the same commercial smartphone. The proposed multi-mode WPT module can cover WPC and PMA mode based on inductive coupling. Moreover, it has more than 20 dB return loss characteristics at two different frequency bands including 6.78 MHz and 13.56 MHz, and shows more than 70 % transfer efficiency between resonant coils at 6.78 MHz in magnetic resonant charging environment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.121-126
• /
• 2013

Cycloconverter used as a power conversion device in the speed and torque control system of AC machines has the advantage of a simple control and a large torque at low speed. In addition, because a rectifier, a DC link, and an inverter are not installed, this system is simple and suitable for large power system. If a power conversion device, which is currently used as a propulsion motor of large vessel, is changed into cycloconverter, the system is simplified and then the installation costs can be significantly reduced. However, conventional cycloconverter has the increased harmonics because the power loss is large and the waveform of output voltage is distorted, due to the high-speed switching of power semiconductor devices. In order to improve these shortcomings, this paper describes a phase shifting filter which is composed of two inputs with different phases in the primary side and one output in the secondary one. As the voltage waveforms with two different phases are added and transformed into the secondary side, these outputs are close to sinusoidal waves. Thereby the voltage waveforms, which are applied to the propulsion motors, are improved and total harmonic distortions (THDs) are significantly reduced.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.8
• /
• pp.1285-1290
• /
• 2017

In this paper, we developed a core module of the steering system to control and operate the outboard ship with the automatic steering system, and implemented it as a complete integrated system. In particular, this paper presents the problem of the rudder sensor used in the existing system and implements the contactless rudder sensor as an improvement. In the case of existing rudder sensors, there is a problem that safety operation and economic loss of the ship operation is caused by malfunction due to immersion during use in outboard vessels. However, the proposed rudder sensor is separated from the rotary shaft to constitute a contactless type, and a circular magnet is fixed so that the rotating value can be detected and used by the Hall sensor to completely solve the flooding problem. As a result of the characteristic test, the voltage value from 1.8V to 3.2V was obtained between $-35^{\circ}$ and $+35^{\circ}$ degrees and satisfied the reference value. The proposed rudder sensor was mounted on the outboard ship, and all the performance of controller system were checked. According to the system proposed in this paper, it satisfies the Korean Standard Specification, which defines the speed of convergence in 30 seconds by switching from left to right in 7 seconds. We also confirmed that automatic steering was performed by comparing the compass sensor with the destination in the integrated controller at the start-up.