• Journal of the Korean Wood Science and Technology
• /
• v.36 no.2
• /
• pp.20-28
• /
• 2008

This study was carried out to provide the so-called circumferential slicing method for investigating radial distributions of the tangential strains and of moisture contents within the log cross section (LC) of Kalopanax pictus during indoor drying it. While the heartwood showed an almost uniform moisture content distribution in the range of about 50~55% in case of the green wood, it has gradually decreased toward the outer side, showing about 19% of moisture content difference from the innermost slice. Although the moisture gradient along the radial direction has gradually become gentle as drying progresses, the sapwood of the outer side represented the moisture contents below the fiber saturation point after 24 hours of drying while the heartwood in the inner part showed the moisture contents higher than the fiber saturation point. The pith side was laid under the tensile stress after 24 hours of drying, and then gradually decreasing toward the bark side, and showed the distribution being switched again to the tensile stress on the bark side. As the drying has progressed, this trend got more intensified, and finally showed the U-shaped distribution model after 48 hours of drying. The circumferential slice test is considered to be suitable in quantitatively determining the tangential strains and moisture content within a LC.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.667-669
• /
• 2007

This letter presents a smart integrated microfluidic device which can be applied to actively immobilize proteins on demand. The active component in the device is a temperature-controllable microelectrode array with a smart polymer film, poly(N-isopropylacrylamide) (PNIPAAm) which can be thermally switched between hydrophilic and hydrophobic states. It is integrated into a micro hot diaphragm having an integrated micro heater and temperature sensors on a 2-micrometer-thick silicon oxide/silicon nitride/silicon oxide (O/N/O) template. Only 36 mW is required to heat the large template area of 2 mm${\times}$16 mm to $40^{\circ}C$ within 1 second. To relay the stimulus-response activity to the microelectrode surface, the interface is modified with a smart polymer. For a model biomolecular affinity test, an anti-6-(2, 4-dinitrophenyl) aminohexanoic acid (DNP) antibody protein immobilization on the microelectrodes is demonstrated by fluorescence patterns.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.71-82
• /
• 2004

Recently, network model inspired by social insect behavior attracts the public attention. The AntNet is an adaptive and distributed routing algorithm using mobile agents, called ants, that mimic the activities of social insect. In this paper. we present a new hardware architecture to realize an AntNet-based routing in practical system on a chip application. The modified AntNet algorithm for hardware implementation is compared with the original algorithm on the various traffic patterns and topologies. Implementation results show that the proposed architecture is suitable and efficient to realize adaptive routing based on the AntNet.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.743-750
• /
• 2011

This article deals with the sensor-less control of a DC Motor via a SEPIC Converter-Full Bridge combination powered through solar panels. We simultaneously regulate, both, the output voltage of the SEPIC-converter to a value larger than the solar panel output voltage, and the shaft angular velocity, in any of the turning senses, so that it tracks a pre-specified constant reference. The main result of our proposed control scheme is an efficient linear controller obtained via Lyapunov. This controller is based on measurements of the converter currents and voltages, and the DC motor armature current. The control law is derived using an exact stabilization error dynamics model, from which a static linear passive feedback control law is derived. All values of the constant references are parameterized in terms of the equilibrium point of the multivariable system: the SEPIC converter desired output voltage, the solar panel output voltage at its Maximun Power Point (MPP), and the DC motor desired constant angular velocity. The switched control realization of the designed average continuous feedback control law is accomplished by means of a, discrete-valued, Pulse Width Modulation (PWM). Experimental results are presented demonstrating the viability of our proposal.

• Journal of Information Processing Systems
• /
• v.7 no.4
• /
• pp.679-690
• /
• 2011

In this paper we consider a local area network (LAN) of dual mode service where one is a token bus and the other is a carrier sense multiple access with a collision detection (CSMA/CD) bus. The objective of the paper is to find the overall cell/packet dropping probability of a dual mode LAN for finite length queue M/G/1(m) traffic. Here, the offered traffic of the LAN is taken to be the equivalent carried traffic of a one-millisecond delay. The concept of a tabular solution for two-dimensional Poisson's traffic of circuit switching is adapted here to find the cell dropping probability of the dual mode packet service. Although the work is done for the traffic of similar bandwidth, it can be extended for the case of a dissimilar bandwidth of a circuit switched network.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.798-810
• /
• 2017

This paper presents a combined system of a small-capacity inverter and multigroup delta-connected thyristor switched capacitors (TSCs). The system is referred to as a hybrid static compensator (HSC) and has the functions of dynamic reactive power compensation and harmonic suppression. In the proposed topology, the load reactive power is mainly compensated by the TSCs. Meanwhile the inverter is meant to cooperate with TSCs to achieve continuous reactive power compensation, and to filter the harmonics generated by nonlinear loads and the TSCs. First, the structure and mathematical model of the HSC are discussed Then the control method of the HSC is presented. An improved reduced order generalized integrator (ROGI)-based selective current control method is adopted in the inverter to achieve high-performance reactive and harmonic current compensation. Meanwhile, a switch control strategy is proposed to implement precise and fast switching of the TSCs and to avoid changing the time delay needed by the conventional switch strategy. Experiments are implemented on a 20 KVA HSC prototype and the obtained results verify the validity of the proposed HSC system.

• Journal of Chest Surgery
• /
• v.20 no.4
• /
• pp.643-654
• /
• 1987

The effect of prostacyclin[PGI, ] on myocardial preservation during global ischemia was studied in the isolating working rabbit heart model. Forty hearts underwent a 15 minute period of retrograde nonworking perfusion with Krebs-Henseleit buffer solution [37*C] and were switched over to the working mode for 15 minutes. After baseline measurement of heart rate, peak aortic pressure, aortic flow, and coronary flow, all hearts were subjected to 60 minutes of ischemic arrest at 10*C induced with St. Thomas Hospital cardioplegic solution: Group I had single dose cardioplegia, Croup II double dose, Croup III oxygenated double dose, and Group IV single dose with PCI, infusion [10ng/min./gm heart weight]. Hearts were then revived with 15 minute period of nonworking reperfusion at normothermia, followed by 30 minutes of working perfusion. Repeat measurements of cardiac function were obtained and expressed as a percent of the preischemic baseline values. Oxygen content of arterial perfusate and coronary effluent was measured by designed time interval. Leakage of creatine kinase was determined during post-ischemic reperfusion period. Finally wet hearts were weighed and placed in 120*C oven for 36 hours for measurement of dry weight. In the PGI, treated group [IV], heart rate increased consistently throughout the period of reperfusion from 100*5.0% [p<0.001] to 107*6.2% [p<0.001]. The percent recovery of aortic flow showed 95*5.7% [p<0.001] at the first 3 minute and full recovery through the subsequent time. Coronary flow was augmented significantly in the 3 minute [96*6.2%, p<0.001] and then sustained above baseline values. Among the Croup I, II, and III, all hemodynamic values were significantly below preischemic levels. PGI2 relatively increased oxygen delivery [1.22*0.19ml/min, p<0.001] and myocardial oxygen consumption [0.90*0.13ml/min, p<0.001] during reperfusion period. Leakage of creatine kinase in the PGI2 group was 9.3*1.58IU/15min [p<0.001]. This was significantly lower than Group I [33.0*2.68 IU/15min]. The water content of PCI2 treated hearts [81*0.9%, p<0.001] was also lower than the other groups.

• The Journal of the Korea Contents Association
• /
• v.17 no.3
• /
• pp.589-595
• /
• 2017

We present an estimation model for optimal channel capacity required to data traffic transmission. The optimal channel capacity should be calculated in order to satisfy the permitted transmission delay of each wireless data services. Considering the discrete-time operation of digital communication systems and batch arrival of packet-switched traffic for various wireless services, $Geo^x$/G/1 non-preemptive priority queueing model is analyzed. Based on the heuristic interpretation of the mean waiting time, the mean waiting times of various data packets which have the service priority. Using the mean waiting times of service classes, we propose the procedure of determining the optimal channel capacity to satisfy the quality of service requirement of the mean delay of wireless services. We look forward to applying our results to improvement in wireless data services and economic operation of the network facilities.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.586-592
• /
• 2018

SRMs are difficult to design using a simple mathematical model and, consequently, numerical analysis based characteristics analysis is used including drive circuits. In this process, it is necessary to analyze the trends according to the change of the design factors, however, many of the design factors affect each other. In order to shorten the design time and achieve a proper design, a modeling technique based on the design parameters is needed. For this purpose, this paper summarizes the formulas employed for shape modeling by minimizing the number of major design factors of the SRM, and proposes a methodology for SRM design using these formulas. In particular, we propose a design method for a 6/4-pole model, one which has been studied for a long time, and showed an example of a design produced by the proposed method.

• Korea Trade Review
• /
• v.41 no.4
• /
• pp.221-243
• /
• 2016

This study examined the trade of the Central Asian CIS countries and the Daegu-Gyeongbuk region. These countries are rich in resources such as oil, natural gas and aluminum. These countries were switched to capitalist market economy after independence from the Soviet Union. So, these countries are considered as new emerging markets. This study analyzed the current status of trade between Daegu-Gyeongbuk region and Central Asian CIS countries. The result of analysis of the trade structure between the Daegu-Gyeongbuk and Central Asian CIS countries, and of the Daegu-Gyeongbuk region exports to Central Asian CIS countries showed insufficience when compared with the total export of korea. In this study, we used the gravity model to analyze the trade volume of the Daegu-Gyeongbuk region and Central Asian CIS countries. The result of analysis is that the globalization of Central Asian CIS countries appeared to be effective in increasing trade. In order to increase trade, Korea and CIS countries should strengthen their economic cooperation. Especially, these countries should try to implement FTAs for economic integration. The Central Asian CIS countries have an industrial structure that relies on resource exports. So, they have a blueprint for diversification of industries through national long-term plans. The Daegu-Gyeongbuk region's economy has been going through long-term stagnation. If the Daegu-Gyeongbuk companies can enter the Central Asian CIS countries, it can be a solution for the local economy.