• 한국인터넷방송통신학회논문지
• /
• 제23권4호
• /
• pp.137-142
• /
• 2023

SMPS(Switched Mode Power Supply, 전력공급장치) 회로설계 시 특별한 고찰 없이 지나치기 쉬운 부분이 스너버(snubber) 회로이다. 그러나 스너버(snubber) 회로에 따른 SMPS의 성능저하 및 SET 전체에 미치는 영향은 결코 무시할 수 없다. 또한 스위칭시 피크치 전압과 전류로부터 소자를 보호하고 on/off 스위칭시 손실을 줄여주기 위하여 스위치 양단에 스너버(snubber) 회로를 부가해준다. 따라서 본 논문에서는 스너버(snubber) 회로에 대한 충분한 이해를 위해 이론적 해석 및 실제 회로설계 때 설계자가 응용할 수 있는 실험식을 정리하여, 스너버(snubber) 회로의 최적화를 도모하고자 한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1891-1895
• /
• 2003

Switch-mode power supplies (SMPS) have become a major source of conducted electromagnetic interference (EMI) which is the combination between differential mode (DM) noise and common mode (CM) noise. This paper presents the conducted EMI reduction approach in flyback switched mode power supply by rerouting for circuit balance to reduce common mode noise. And differential mode noise can be reduce by adding $c_x$ capacitor across the input power line, and passive element to the gate drive of switching device MOSFET to slow down the switching times. This combination of our approach is the effective way to reduce the conducted EMI and it is also a cost effective for product design

• Journal of Electrical Engineering and Technology
• /
• 제11권3호
• /
• pp.575-584
• /
• 2016

Considering the randomness and uncertainty of wind power, a reliability model of WTGs is established based on the combination of the Weibull distribution and the Markov chain. To analyze the failure mode quickly, we use the switch-section partitioning method. After defining the first-level load zone node, we can obtain the supply power sets of the first-level load zone nodes with each WTG. Based on the supply sets, we propose the dynamic division strategy of island operation. By adopting the fault analysis method with the attributes defined in the switch-section, we evaluate the reliability of the distribution network with WTGs using a sequential Monte Carlo simulation method. Finally, using the IEEE RBTS Bus6 test system, we demonstrate the efficacy of the proposed model and method by comparing different schemes to access the WTGs.

• 전기전자학회논문지
• /
• 제14권2호
• /
• pp.1-8
• /
• 2010

본 논문에서는 대기전력을 줄일 수 있는 Green Mode Power IC 회로를 설계하였다. 이 회로는 switch mode power supply(SMPS)을 구동하기 위한 PWM 기능을 가지고 있으며, 불필요한 소비전력을 제거하기 위해 burst mode와 skip mode 구간을 만들고 대기전력을 낮출 수 있도록 외부의 Power MOSFET에 의해 제어된다. 제안한 회로는 KEC 30V-High Voltage 0.5um CMOS process를 이용하여 시뮬레이션 하였다. 회로 내부는 크게 voltage regulator 회로, voltage reference 회로, UVLO(Under Voltage Lock Out)회로, Ibias 회로, green 회로, PWM 회로, OSC 회로, protection회로, control 회로, Level shift&Driver 회로로 구성되어 있다. 시뮬레이션 결과로부터 회로 동작 시 각 블록의 소비전류를 측정하여 확인한 결과 블록 별 전류총합이 1.29mA이었고, 이 값은 목표 설계치인 1.3mA을 충족시킴을 입증하였다. 이 값은 기존 IC의 소비전류보다 1/2이상 줄어든 값이며, 대기모드로 동작할 경우는 전력소비를 1W 미만까지 줄일 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2112-2114
• /
• 1998

A gate driver suitable for forced switch-mode power converters such as UPS and motor drive system is presented. The proposed gate driver uses regenerated snubber power and requires no separate power supply. This does not impose any additional complexity on the main switch. Experimental results show that the proposed circuit is valid.

• 조명전기설비학회논문지
• /
• 제23권7호
• /
• pp.20-28
• /
• 2009

This paper presents the design of zero current switching ZCS pulse frequency modulation type DC-DC converter for magnetron power supply. A magnetron serving as the microwave source in a microwave oven is driven by a switch mode power supply (SMPS). SMPSs have the advantages of improved efficiency, reduced size and weight, regulation and the ability to operate directly from the converter DC bus. The demands of the load system and the design of the power supply required to produce constant power at 4[kV]. A magnetron power supply requires the ability to limit the load current under short circuit conditions. The current source series resonant converter is a circuit configuration which can achieve this. The main features of the proposed converter are an inherent protection against a short circuit at the output, a high voltage gain and zero current switching over a large range of output power. These characteristics make it a viable choice for the implementation of a high voltage magnetron power supply.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권8호
• /
• pp.392-401
• /
• 2001

This paper presents the single-stage high power factor AC to DC converter operated in active-clamp mode. The proposed converter is added active-clamping circuit to boost-flyback single-stage power factor corrected power supply. The active-clamping circuit limits voltage spikes, recycles the energy trapped in the leakage inductance, and provides a mechanism for achieving soft switching of the electronic switches to reduce the switching loss. The auxiliary switch of active-clamping circuit uses the same control and driver circuit as the main switch to reduce the additional cost and size. To verify the performance of the proposed converter, a 100W converter has been designed. The proposed converter gives good power factor correction, low line current harmonic distortions, and tight output voltage regulation, as used unity power factor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.253-257
• /
• 2003

This paper presents the Development of Switching Power Supply for testing communication equipment. The communication equipment need many kinds of voltage(-48V,27V,12V,5V,3.3V), and in case of low voltage needs large current($10{\sim}20A$). The previous Linear Power Supply was very heavy, has low efficiency and poor power-factor for testing communication equipment. This development has good efficiency and high power-factor using switch mode power supply technique. This Development of Switching Power Supply is composed of eight converters. The principles of operation, feature, and design considerations are illustrated and verified through the experiment with 600W prototype.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1221-1226
• /
• 2015

This paper proposes a multiple switch mode power supply (SMPS) system based on the wireless network which controls variable load. The system enables power supply of up to 600W using 200W SMPS as a unit module and provides a controlling function of output power based on variable load and a monitoring function based on wireless network. The controlling function for output power measures the variation of output power and facilitates efficient power supply by controlling output power based on the measured variation value. The monitoring function guarantees a stable power supply by observing the multiple SMPS system in real time via wireless network. The performance of the proposed system was examined by various experiments. In addition, it was verified through standardized test of Korea Testing Certification. The results were given and discussed.

• 한국산업융합학회 논문집
• /
• 제25권3호
• /
• pp.423-431
• /
• 2022

The UPS(Uninterruptible Power Supply) system operates in the battery charging mode when the grid is normal, and in the UPS mode, which is the battery discharge mode when a grid error occurs. Since the UPS must supply the same voltage as the grid to the load within 4 [ms] in case of a grid error, the switching time and power recovery time should be short when controlling the output voltage and current of the UPS, and the power failure detection time is also important. The power outage detection algorithm using DFT(Discrete Fourier Transform) proposed in this paper compares the grid voltage waveform with the voltage waveform including the 9th harmonic generated through DFT using Schmitt trigger to detect power outage faster than the existing power outage monitoring algorithm. There are advantages. Therefore, it is possible to supply instant and stable power when switching modes in the UPS system. The multi-power-applied UPS system proposed in this paper uses DFT, which is faster than the conventional blackout monitoring algorithm in detecting power failure, to provide stable power to the load in a shorter time than the existing power outage monitoring algorithm when a system error occurs. The detection method was applied. The changeover time of mode switching was set to less than 4 [ms], which is 1/4 of the system cycle, in accordance with KSC 4310 regulation, which was established by the Industrial Standards Council on the regulation of uninterruptible power supply. A 10 [kW] UPS system in which commercial voltage, vehicle generator, and auxiliary diesel generator can be connected to each of the proposed transfer devices was constructed and the feasibility was verified by conducting an experiment.