• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1923-1929
• /
• 2009

The design of SPMSM(surface mounted permanent magnet synchronous motor) has been performed to reduce cogging torque and torque ripples. In general, cogging torque and torque ripples are affected by the shapes of teeth width, yoke depth, magnet pole arc, etc. Particularly, the minimum design point of cogging torque and torque ripples are different so that the design of SPMSM should be done to compromise both of them for precision application. In this paper, the design of PMSM for EPS(electric power steering) system is performed to verify the validity, and the design characteristics versus teeth width, yoke depth, and magnet pole arc are investigated in order to find out the minimum point of cogging torque and torque ripples. In addition, skew of PM is applied for cogging torque reduction.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.526-531
• /
• 2012

This paper, we describe the vector control of surface mounted PMSM (Permanent Magnet Synchronous Motor) using the fuzzy controller which is suggested algorithm. In these days, when vehicle is operated or not, whether the road is covered or not, the sensitivity of the steering column is not stable. To make up for it, the PI gain of a steering column controller is adjusted by experience. It becomes the price because it need a lot of sensor. Also it is difficult to implement robust control because we need a lot of parameters for variable road conditions which are the off road, the on road, a low battery voltage, a high battery voltage, a vehicle speed. In this paper, we propose fuzzy controller using the suggested algorithm which suitable for steering system. We test the fuzzy controller with the various condition. We get the good performance of fuzzy controller even if it is nonlinear system. We check a robust the fuzzy controller using the suggested algorithm.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.534-542
• /
• 2005

This paper proposes the fuzzy logic based vector control method for a Surface Mounted Permanent Magnet Synchronous Motor(SMPMSM) used in the elevators. The gain of a conventional PI speed controller in the elevator drive system can not be usually set high due to mechanical resonances, therefore its performance becomes deteriorated. There have been many methods to solve above problems such as an acceleration feedback in the speed controller. However, the above methods have defects that parameter information is demanded. In this paper', a Fuzzy controller(FC) is adopted in the elevator drive system. The performance of a fuzzy controller is compared with a PI controller in the no load and load conditions by simulation and experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.165-173
• /
• 2013

Core loss has a major effect on heat generation in synchronous motors with surface-mounted permanent magnets (SPMs). It is essential to perform heat transfer analysis considering core loss in SPM because core loss is seriously affected by torque and speed of motors. In the present study, mechanical loss, core loss and coil loss are evaluated by measuring input and output energies under various driving conditions. For a better understanding heat transfer paths in synchronous motors, we developed a lumped thermal system analysis model. Subsequently, heat transfer analysis has been performed based on acquired energy loss, temperature data and thermal resistance with three types of SPM. It is shown that the torque constants decrease by Max. 10% as speed increase. At the rated torque, the core loss is Max. 10.9 times greater than the coil loss and the hysteresis loss of magnets is dominant in total loss.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.179-182
• /
• 1998

This paper is proposed a selection method of the major design dimension which constrain the maximum acceleration capability and minimum power loss of surface-mounted brushless do motor with NdFeB permanent magnet for servo drives. Expressions are derived from the air-gap flux density and the linear current density around the stator periphery and design dimensions. The linear current density is limited by the need to avoid demagnetization. In this paper, We compute the optimum design dimensions of 2KW BLDC motor with maximum acceleration capability and minimum power loss by using genetic algorithm.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.920-922
• /
• 2002

This paper investigates the cogging torque reduction in a brushless DC(BLDC) motor having an inner-rotor with surface-mounted segment-type permanent magnets. The kind of magnets for the BLDC motor could have different waveforms of magnetization such as square, trapezoidal and sinusoidal form. This paper discusses the effect of the unsymmetrical magnetization distribution in the segment-type permanent magnet, which is able to obtain through a segment structure that the number of poles per segments is 2 ($N_p/N_s$), on the cogging torque and EMF waveform. Where the existing magnetizer fixture for the square-type magnetization is used to magnetize the magnets in two segment structures of $N_p/N_s$ = 1 and 2. The effectiveness of the proposed designs had been confirmed by comparing cogging torque, and EMF waveform between conventional and new models which are analyzed by Finite Element Method (FEM).

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.613_614
• /
• 2009

Electric power steering(EPS) has many attentions such as fuel consumption improvement, thus it has been widely adopted for automotive application in recent years. In the EPS system, torque vibrations are directly transferred through the steering wheel to the hands of the driver. Hence, the design of PM motors for the EPS should be performed in order to reduce torque ripples including cogging torque. In this paper, Surface mounted Permanent Magnet Synchronous Motor(SPMSM) is designed to reduce torque ripples and cogging torque at a same time for the EPS propulsion and the design results are verified with the experimental ones.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1059-1061
• /
• 2000

본 논문에서는 속도검출기가 없는 표면부착형 영구자석 동기 전동기의 속도제어 기법을 제안한다. 표면부착형 영구자석 동기 전동기는 그 형상에 있어서는 자기적 돌극성을 가지지 않지만 기본 주파수에 비하여 높은 주파수를 가지는 전압을 전동기의 추정된 회전사의 위치와 같은 축에 인가함으로써 자속의 포화에 의한 고주파 임피던스의 차이를 관측할 수 있다. 본 논문에서는 이 고주파 임피던스의 차이를 이용하여 전동기회전자의 위치를 추정하고, 추정된 회전자의 위치를 이용하여 속도 및 위치 검출기가 없이도 벡터제어를 수행한다. 또한, 이 고주파 임피던스의 특성은 부하조건에 따라 변하기 때문에 추정하는 회전자의 위치가 부하조건에 따라서 왜곡된다. 본 논문에서는 회전자의 위치를 추정한 후 부하조건에 따라 회전자의 위치를 보정하는 기법도 제안한다. 마지막으로 실험을 통하여 제안된 기법의 타당성을 검증한다.

• Journal of Industrial Technology
• /
• v.31 no.A
• /
• pp.129-133
• /
• 2011

In this paper, a surface mounted permanent magnet synchronous motor(SPMSM) drive system for industrial sewing machine was developed. Even through a lowr-esolution encoder is used for a low cost, using a full order observer enables to estimate accurate speed and position. And it also compensates a disturbance torque caused by the belt between a load and a motor. In order to control precisely stop positions of a needle, a speed trajectory is calculated from the acceleration pattern which is obtained from the position reference. The performance of the developed system is verified by experimental results.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.9-11
• /
• 2009

자동차 EPS(Electric Power Steering)용 소용량 표면부착형 영구자석 동기전동기(SPMSM : Surface mounted Permanent Magnet Synchronous Motor)의 설계에는 주로 토크리플 및 코깅토크 저감이 설계목표로 결정되는데, 토크리플과 코깅토크는 치폭, 요크폭, 자석 극호각 등 전동기 형상에 영향을 많이 받는다. 특히, 자석 극호각에 따라 변동이 극심한데, 이는 출력특성이 공극 자속밀도 변화량에 크게 의존하기 때문이다. 한편, 일반적으로 토크리플과 코깅토크의 최소점은 각각 다르기 때문에, 소용량 SPMSM 설계시 큰 어려움으로 작용한다. 따라서 본 논문은 이러한 현상을 효과적으로 고려한 소용량 SPMSM 최적설계를 목적으로 하며, 600W급 고전압 EPS용 전동기 설계를 통해 연구의 타당성을 검증한다.