• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.116-122
• /
• 2013

For fabricating silicon solar cells with high conversion efficiency, texturing is one of the most effective techniques to increase short circuit current by enhancing light trapping. In this study, four different types of textures, large V-groove, large U-groove, small V-groove, and small U-groove, were prepared by a wet etching process. Silicon substrates with V-grooves were fabricated by an anisotropic etching process using a KOH solution mixed with isopropyl alcohol (IPA), and the size of the V-grooves was controlled by varying the concentration of IPA. The isotropic etching process following anisotropic etching resulted in U-grooves and the isotropic etching time was determined to obtain U-grooves with an opening angle of approximately $60^{\circ}$. The results indicated that U-grooves had a larger diffuse reflectance than V-grooves and the reflectances of small grooves was slightly higher than those of large grooves depending on the size of the grooves. Then amorphous Si:H thin film solar cells were fabricated on textured substrates to investigate the light trapping effect of textures with different shapes and sizes. Among the textures fabricated in this work, the solar cells on the substrate with small U-grooves had the largest short circuit current, 19.20 mA/$cm^2$. External quantum efficiency data also demonstrated that the small, U-shape textures are more effective for light trapping than large, V-shape textures.

• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.44-49
• /
• 1992

Magnetic properties and microstructures of $Nd_{12}Fe_{80}B_{6}(Nb,\;M)$ (M=Ti/Cu/Ga) melt-spun ribbons prepared by single wheel technique have been studied. The results of microstructural study have shown that Ga is effective for the orientation of c-axis normal to the ribbon plane. The Ga-added melt-spun ribbon, $Nd_{12}Fe_{80}B_{6}(Nb,\;Ga)$, quenched at $V_{s}=17.9\;m/s$ was mostly composed of fine grains of about 30 nm in size with the textured free-side surface. The powder of this ribbon aligned in mag-netic field showd a high remanence of 0.87 T which was about 5 % higher than that of ribbon itself. It is believed that there is a possibility to fabricate a new type of HIREM melt-spun ribbon with highly textured free-side surface.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.401-406
• /
• 2015

Getter is a class of materials used in absorbing gases such as hydrogen and moisture in microelectronics or semiconductor devices to operate properly. In this study, we developed a new device structure consisting of porous anodized alumina films on textured silicon wafer, which have cost efficiency in materials and processing aspects. Anodic aluminum oxide (AAO) with controlled pore sizes can be applied to a high-efficiency moisture absorber due to the high surface area and OH- saturated surface property. The moisture sorption capacity was 2.02% (RH=35%), obtained by analyzing isothermal adsorption/desorption curve.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.282-283
• /
• 2005

Ion beam assisted deposition(IBAD) technique was used to produce biaxially textured polycrystalline MgO thin films for high critical current YBCO coated conductor. Hastelloy tapes were continuous electropolished with very smooth surface for IBAD-MgO deposition, RMS roughness of Hastelloy tape values below 2 nm and local slope of less than $1^{\circ}$. After the polishing of the tape an amorphous $Y_2O_3$ and $Al_2O_3$ are deposited Biaxially textured MgO was deposited on amorphous layer bye-beam evaporation with a simultaneous bombardment of high energy ions. We had developed the RHEED to measure in-situ biaxial texture of film surface as thin as tens angstrom. And also ex-situ characterization of buffer layers was studied using XRD and SEM. The full-width at half maximum(FWHM) out of plane texture of IBAD-MgO template is $4^{\circ}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.90-93
• /
• 2004

In this work, we have used different techniques for the surface passivation: conventional thermal oxidation (CTO), rapid thermal oxidation (RTO), and plasma-enhanced chemical vapour deposition (PECVD). The surface passivation qualities of eight different single and combined double layer have been investigated both on the phosphorus non-diffused p-type FZ silicon and on phosphorus diffused emitter of 100 ${\Omega}/Sq$ and 40 ${\Omega}/Sq$. In the single layer, silicon dioxide $(SiO_2)$ passivates good on the emitter while silicon nitride (SiN) passivates better than on the non-diffused surface. In the double layers, CTO/SiN1 passivates very well both on non-diffused surface on the emitter. However, RTO/SiN1 and RTO/SiN2 stacks are more suitable for surface passivation in solar cells caused by a relatively good passivation qualities and the low optical reflection. Applying these stacks in solar cells we achieved 18.5 % and 18.8 % on 0.5 ${\Omega}$ cm FZ-Si with planar and textured front surface, respectively. The excellent open circuit voltage $(V_{oc})$ of 675.6 mV is obtained the planar cell with RTO/SiN stack.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.spc
• /
• pp.40-44
• /
• 2009

This study was carried for the understanding of infiltration and percolation characteristics of water in agricultural land filled with rock-dust (Technosols). The experiment was performed at two sites (A, B), and soil horizons of the sites were classified with 4 layers, respectively. The soil texture of all soil horizons was analyzed with silt loam (SiL) except for the soil texture, which was loamy sand (LS), at the lowest horizon of measurement site A. The bulk densities at each horizon of two soils were mostly over $1.49g{\cdot}cm^{-3}$, which is very higher than $1.25g{\cdot}cm^{-3}$ of typical medium-textured mineral soil, except for the surface of site A measured immediately after tillage. The concentrations of $P_2O_5$ at surface of two soils s were 1962 (A), 1613 (B) $mg{\cdot}kg^{-1}$, respectively. These concentrations are 3.2~6.5 times of $300{\sim}500mg{\cdot}kg^{-1}$, which is the optimum concentration for crop growth. Infiltration rates at surface of the soils were 3.54 (A), 2.85 (B) cm $hr^{-1}$, but percolation rates at soil horizons under the surface were below 0.3 (A), below 0.003 (B) cm $hr^{-1}$. These results would be because the surface soils were managed by tillage and crop planting etc., but soils under surface were formed with structural problems occurred at the formation time of agricultural land accumulated with rock-dust or a compaction by farm machines.

• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.2
• /
• pp.71-75
• /
• 2002

GaAs polycrystalline thin films with good performance were prepared on conducting glass by hot wall epitaxy (HWE), which were used for solar cell. Electron probe micro-analyzer (EPMA) was applied for the composition, morphology of surface and cross-section of grown films, and X-ray diffraction (XRD) for their phase structure; Raman scattering spectum (RSS) and photoluminescence (PL) were used for evaluating their optical characteristics. The results show that, there is textured structure on the surface of grown GaAs polycrystalline films, which is greatly promised to be suitable for the candidate of solar cell with low cost and high efficiency. It is concluded that the source and substrate at temperature of 900 ~ 930 $\^{C}$ and 500 $\^{C}$ respectively would be beneficial for such films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.107-110
• /
• 2002

The optical memory devices of BST thin films to composite $(Ba_{0.7}\;Sr_{0.3})TiO_{3}$ using sol-gel method were fabricated by changing of the depositing layer number on $Pt/Ti/SiO_{2}/Si$ substrate. The structural properties of optical memory devices to be ferroelectric was investigated by fractal analysis and 3-dimension image processing. The thickness of BST thin films at each coating numbers 3, 4 and 5 times was $2500[\AA]$, $3500[\AA]$ and $3800[\AA]$. BST thin films exhibited the most pronounced grain growth. The surface morphology image was roughness with coating numbers. The thin films increasing with coating numbers shows a more textured and complex configuration.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.3
• /
• pp.11-14
• /
• 2003

The detailed conditions of dc-sputtering for depositions of yttria-stabilized ZrO$_2$ (YSZ) films were investigated, while the films were grown on the CeO$_2$ template layers on biaxially textured Ni-tapes. The window of oxygen pressures for proper growth of YSZ films, which was dependent on sputtering powers, was determined by sufficient oxidations of the YSZ films and the de-oxidation of the target surface, which was required for rapid sputtering. The window turned out to be fairly wide under certain values of argon pressure. When the sputtering power was raised, the deposition rate increased without narrowing the window. The fabricated YSZ films showed good texture qualities and surface morphologies.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.326-328
• /
• 1999

We investigated the effects of residual gas partial pressure on the property of a CeO$_2$ buffer layer on a textured Ni tape, where the buffer layer was deposited by e-beam evaporation. The oxygen partial pressure were varied from 10$^{-7}$ to 10$^{-4}$ Torr. we also changed the surface condition for the surface oxygenation. We'll describe the detail of the resultant textures of the buffer layers and effects of YBCO growth on them