• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.379-388
• /
• 2004

To investigate the effect of D-ferrite on the hot workability and surface defect of STS 304 billets containing 3 wt. % Cu, microstructure observations and high temperature mechanical properties test were carried out for the specimens extracted mainly from raw or oxidized billets. It was found that the total $\delta$-ferrite content has little influence on the hot workability, even though the fracture cracks due to high temperature tension or compression test were initiated and propagated mostly along $\delta$/${\gamma}$ boundary in the specimens. On the other hand, it was supposed that the direct causes of surface defects in the wire rolled from the as-continuously cast billet were the grain boundary embrittlement arose from the deep diffusion of oxygen into the grain boundary, and the oxidation of $\delta$-ferrite connected by a grain boundary to the surface during the billet reheating process as well.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.6 s.73
• /
• pp.769-780
• /
• 2004

This paper's objective is to evaluate the experimental behavior of gap N-joints made of cold-formed, square, hollow steel sections, with a connection plate as a tension member. The principal parameters for testing included the ratio of chord width to thickness, the ratio of brace width to chord width, eccentric ratio, the shape of the compression member, the branch angle, and the stiffening plate of the chord flange. The strength and failure mode were examined through the test for the gap N-joint, consisting of several parameters. Based on the results of the test, the gap N-joints were determined according to the capacity preceding the displacement of the tension, regardless of the width ratio, and the split failure mode-connected surface for a chord in joints. The strength of the gap N-joints increased proportionally as the $2\gamma$(B/T) ratio decreased, and as the width ratio(${\beta}$) of branch to chord increased. Particularly, $2\gamma$(B/T) decreased as the capacity of gap N-joint increased. The results of the test were summarized for the capacity, initial stiffness, ductility, and change of the failure mode of each gap N-joint.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.3
• /
• pp.184-188
• /
• 1996

The Acinetobacter sp. BE-254 isolated from soil sources produced a bioemulsifier in the medium supplemented with n-hexadecane. This bioemulsifier was purified by the procedures of fractionation (ammonium sulfate and chilled acetone), extraction by hexane, and column chromatography on silica gel 60. The results from various color reactions indicated that the bioemulsifier was a glycolipid. The purified emulsifier was very stable at pHs ranging from 4 to 10 and under heat treatment at $100^{\circ}C$ for 30 min. Emulsification activity was also hardly influenced by pH. The critical micelle concentration (CMC) and surface tension at the point ($\gamma_{cmc}$) of the bioemulsifier were approximately 35 mg/l and 30 mN/m, respectively. The bioemulsifier showed a fairly good emulsification activity and stability in comparison with other commercial emulsifiers in the basic formula composed of emulsifier, oil, and water.

• Journal of the Korean Society of Safety
• /
• v.12 no.3
• /
• pp.10-16
• /
• 1997

The problem of sound radiation from curved beam under the action of harmonic line forces is studied. The reaction due to fluid loading on the vibratory response of the curved beam is taken into account. The curved beam is assumed to occupy the plane y=0. The curved beam material and the elastic foundation are assumed to be lossless including a tension force(T), damping coefficient(C) and stiffness of foundation($k_s$) will be employed. The non-dimensional sound power is derived through integration of the surface intensity distribution over the entire curved beam. The expression for sound power is integrated numerically and the results are examined as a function of wavenumber ratio($\gamma$) and stiffness factor($\psi$).

• Journal of the Korean Chemical Society
• /
• v.8 no.1
• /
• pp.9-14
• /
• 1964

The viscosities of strong electrolytic solutions, such as KCl, KI and NaI have been measured over a fairy wide range of concentration variation (from 0.00002 to 3.7M). It was hoped that a study of the data in the light of modern theories on solution might reveal new relation between viscosity and surface tension of electrolytic solution. To secure more accurate measurements of viscosity and surface tension of the solutions, Ostwald viscometer was made with pyrex glass and modified the timing system for the transit of the meniscus with a new electronics system and with a pulse counter. As the experimental data obtained were in good agreement with the Jone's values, Jones-Dole equations for the electrolytic solutions were deduced, ${\eta}KCl\;=\;1\;+\;0.0052{\sqrt{c}}\;-\;0.01612c\;+\;0.00808c^2\;at\;30^{\circ}C$ ${\eta}KI\;=\;1\;+\;0.0220{\sqrt{c}}\;-\;0.01290c\;+\;0.02988c^2\;at\;25^{\circ}C$${\eta}Na\; =\;1\;+\;0.0240{\sqrt{c}}\;-\;0.0640c\;+\;0.03268c^2\;at\;25^{\circ}C$Gruneisen effect appeared in the dilute solution, whereas anti-Gruneisen effect was found for the extremely dilute solution. No satisfactory interpretation for the variation of the viscosity with concentration can be found at the present.

• Journal of the Korean Applied Science and Technology
• /
• v.13 no.3
• /
• pp.61-71
• /
• 1996

In acid-catalyzed acetal cyclization of long aliphatic aldehydes($R=n-C_7H_{15}$ ; $n-C_9H_{19}$ ; $n-C_{11}H_{23}$) with 1,1,1-tris(hydroxymethyl)propane, 2-alkyl-5-hydroxymethyl-5-ethyl-1,3-dioxanes were obtained. The final products, sodium 2-alkyl-5-(sulfonatedpropylethermethyl)-5-ethyl-1,3-propanesultion in the presence of sodium hydride. These compounds were a new group of destructible surfactants which were readily hydrolyzed and oxidized in natural water reservoirs. Physical properties of these new compounds involved some surface properties such as Krafft point(Kp), critical micelle concentration(cmc), surface tension of aqueous solutions near cmc(${\gamma}_{min}$), foaming power, emulsion power and hydrolysis properties were determined. The destructible surfactants containing 1,3-dioxane ring were synthesized to about $85{\pm}5.5%$ yield. The cmc values of the compounds by ring method were assumed to $0.5{\sim}5.0{\times}10^{-3}mol/L$ range and surface tensions at cmc were $29.5{\sim}33.0dyne/cm$ respectively at $25^{\circ}C$. The foaming power and foam stability were $170{\sim}230mm$ and $52{\sim}135mm$ respectively at $1{\times}10^{-2}mol/L$, foam was occurred rarely below $1{\times}10^{-3}mol/L$. The emulsion property of liquid paraffin was better than that of soybean oil. For hydrolysis property with ph and time, these compounds were decomposed within about 200minutes at $ph1{\sim}2$. Hopefully these compounds are expected to be a good O/W emulsifier that have decomposability in acid and may be used in the process which do not need foaming.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.299-307
• /
• 1996

The surface tension of PO added sodium poly(oxyethylene(EO), oxyisopropylene(PO)) dodecyl ether sulfate firstly were slightly lower than EO added sulfate in the concentration range of $10^{-6}{\sim}10^{-3}mol/{\ell}$. And they had lower critical micelle concentration ($10^{-4}{\sim}9{\times}10^{-5}mol/{\ell}$) than general anionic surfactants. The adsorptivity ($2.2{\times}10^{-10}mol/cm^2$) of sodium $(PO)_{10}(EO)_5$ dodecyl ether(compound of PO addition firstly) calculated by Gibbs' adsorption isotherm were higher than that of sodium $(EO)_{10}(PO)_5$, dodecyl ether(compound of EO addition firstly), but were lower than that of sodium dodecyl sulfate (${\Gamma}=3.2{\times}10^{-10}mol/cm^2$). These could be understood that the adsorption areas of compounds were very large because of their high molecular weight. Moreover, PO compounds showed better properties than EO compounds in foamability, emulsifying power for organics (n-hexane, benzene), detergency for the lard, tallow oil mixture and dispersability for iron oxide. It was interpreted in terms of surface properties of the PO compounds. These showed that the interfacial activity become higher when hydrophilic and hydrophobic portion existed in aggoromerated state respectively. The test results of emulsifying power for organics (n-hexane, benzene) showed better for benzene than n-hexane. Eight kinds of sodium (EO, PO) dodecyl ether derivatives showed irregular dispersibilities for polar iron oxide in water dispersed media.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.379-384
• /
• 2011

The critical micelle concentration (CMC) and the counter ion binding constant (B) for the mixed micellizations of DBS (sodium dodecylbenzenesulfonate), SDS (sodium dodecylsulfate), and Brij 30 (polyoxyethylene(4) lauryl ether) at $25^{\circ}C$ in pure water were determined by the use of electric conductivity and surface tension measuring methods. Various thermodynamic parameters ($X_i,\;{\gamma}i,\;C_i,\;a_i^M,\;{\beta}$, and ${\Delta}H_{mix}$) were calculated and compared with each other mixed surfactant system by means of the equations derived from the nonideal mixed micellar model. The results show that the SDS molecule interacts more strongly with Brij 30 molecule than DBS molecule and that the SDS/Brij 30 mixed surfactant system has the greatest negative deviation from the ideal mixed micellar model and the SDS/DBS mixed system has followed almost the ideal mixed micellar model.

• Journal of the Korean Applied Science and Technology
• /
• v.8 no.2
• /
• pp.105-114
• /
• 1991

In relation to the preparation of Langmuir-Blodgett thin film, four kinds of N-alkylpyridiniurn bromide were synthesized. The values of surface tensions of these materials, measured with a Traube stalagmometer, gave the relationship between the critical micells hydrophobic radical and between CMC and temperature. Values of thermodynamic properties(${\Delta}H^0_m,\;{\Delta}S^0_m,\;{\Delta}G^0_m,$) for the formatoin of micelle were also obtained. Experiments gave the following results; at the temperature range between 40 and 60$^{\circ}C, CMC of Hexadecyl-, Octadecyl-, Eicosyl-, and Docosyl-Pyridinium Bromide were $7.64{\times}10^{-4}{\sim}9.13{\times}10^{-4},\;3.85{\times}10^{-4}{\sim}4.60{\times}10^{-4},\;2.00{\times}10^{-4}{\sim}2.39{\times}10^{-4},\;and\;1.07{\times}10^{-4}{\sim}1.28{\times}10^{-4}$ mol/l, respectively. Surface tension, ${\Gamma}_{CMC}$, of those were 33.49${\sim}$36.00, 34.78${\sim}$37.61, 35.49${\sim}$37.61 and 38.76${\sim}$55.80 dyne/cm, respectively, The relationship between CMC and the mumber of carbon atoms in the hydrophobic radical, N was expressed as follows : Log(CMC)=A-BN where A and B are constants. At the temperature range between 40 and 60$^{\circ}C$, the change of Gibbs evergy (${\Delta}G_m$) for one methylene group ($-CH_2-$) were -0.65RT, respectively, The minus values of enthalpy change (${\Delta}H_m$) suggest that the formation of micelle is exothermic. Additionally, the overall increase in the entropy change (${\Delta}S_m$) with respect to the temperature increase suggests that the formation of micelle is attained by a exothermic enthalpy directed process.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.2
• /
• pp.105-112
• /
• 2000

Surface tension as a function of concentration and temperature was measured for aquous solution of sodium N-acyl sarcosinate, $RCON(CH_{3})CH_{2}$ COONa, From the intersection points in the (${\gamma}-logC$) curves, the critical micelle concentration (cmc) was determined at 20, 30, 40, and $50^{\circ}C$. Structural effects on the cmc maximum and the minimum area per molecule at the aquous solution/air interface were discussed. The free energy, enthalpy, and entropy of micellization and adsorption of surfactant solution also were investigated. Numberous investigators have dealt with sodium N-acyl sarcosinates and their applications as wettings, flooding and reducing agents and as corrosion inhibitors.