• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.55-60
• /
• 2021

Fluorination was carried out to improve the adsorption performance of pitch-based activated carbon fibers (ACFs) onto acetic acid. Both plasma and direct gas fluorination were used for fluorination, and the acetic acid gas adsorption performance of fluorinated ACFs was investigated. X-ray photoelectron spectroscopy (XPS) is analyzed to determine the surface characteristics of ACFs, and the pore characteristics were analyzed by 77 K nitrogen adsorption. An adsorption performance was measured through gas chromatography, and it was confirmed that the breakthrough time of plasma fluorinated sample was 790 min and that the breakthrough time was delayed compared to that of using untreated one of 650 min. However, the breakthrough time of direct gas fluorinated sample was 390 min, indicating that the adsorption performance was inhibited. The plasma fluorinated ACFs showed an increase in the adsorption performance due to an electrostatic attraction between the acetic acid gas (CH3COOH) with the fluorine group introduced to the surface without changing its specific surface area. On the other hand, the specific surface area of the direct gas fluorinated ACFs decreased significantly up to 55%, and the physical adsorption effect on the acetic acid gas also reduced.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.413-416
• /
• 2001

여러 가지 기능성 섬유나 섬유복합재료에서는 가공성이나 계면접착성 향상 및 응용성을 높이기 위하여 섬유 표면을 개질하여 사용하는 경우가 많다. 지금까지 연구된 섬유의 표면개질 방법으로는 화학적 처리방법, 광화학적 방법, 플라즈마 처리법 등이 개발되어 있다. 화학적 방법은 장비가 간단한 장점이 있지만 사용 약품이 대부분 강한 독성을 지니고 있어서 작업 및 환경오염에 큰 문제점이 있고, 광화학적 방법은 radiation 에너지가 커야 하고 광에너지의 차폐 문제가 있다. (중략)

• Journal of the Korean Chemical Society
• /
• v.47 no.2
• /
• pp.147-154
• /
• 2003

In this study, the fluorinated carbon blacks(CB) were used to reduce the negative temperature coefficient (NTC) phenomenon of the CB-filled high density polyethylene(HDPE) compounds in the fluorination pressure of 0.1-0.4 MPa. The changes in surface properties of the CB were investigated by using FT-IR, XPS and contact angle measurements. From the FT-IR results, the fluorinated CB showed the C-F absorption peak at 1400-1000 cm$^{-1}$ and the peak intensity was increased with increasing the fluorination pressure. Also, the analysis of XPS spectra of the fluorinated CB indicated that fluorine content was increased with increasing the fluorination pressure. Meanwhile, the surface free energy of the fluorinated CB was decreased with increasing the fluorination pressure. Consequently, the increase of fluorine contents on CB made a disappearance of NTC behaviors of CB/HDPE compounds, which was probably due to the reduction of CB reaggregation after melting point of the HDPE, resulting from decreasing the surface free energy of CB particles.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.11a
• /
• pp.172-175
• /
• 2003

• Membrane Journal
• /
• v.25 no.5
• /
• pp.447-455
• /
• 2015

In this study, Polysulfone (PSf) and polyetherimide (PEI) as the anion exchange polymers were aminated in the different ratio whereas the polyether ether ketone (PEEK) as the cation exchange polymer was sulfonated. The bipolar membranes of SPEEK (sulfonated PEEK)/APSf (aminated PSf) and SPEEK/APEI (aminated PEI) were prepared by the double-casting method. The surfaces of bipolar membranes were fluorinated in accordance with the amination ratio and applied to produce the hypochlorite. As the amination increased, the hypochlorite concentration is also increased. Typically, for SPEEK/APSf 3 : 1 membrane, the produced hypochlorite concentration was 61.0 ppm and its durability was 220 min for the non-fluorinated membrane while for the fluorinated membrane, the concentration of 58.6 ppm and its durability lasted 570 min. Also for SPEEK/APEI 3 : 1 membrane, the hypochlorite concentrations of 60.1 ppm and 58.3 ppm for before- and after-fluorination, respectively were observed whereas the durability was remarkably developed from 150 min to 440 min. Therefore, the surface fluorination takes an important role for the development of the membrane durability.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.653-658
• /
• 2021

Polyvinylidene fluoride (PVDF) is a promising coating material because of its outstanding processability. The PVDF coating, however, has limitations in anti-corrosion application due to its weak hydrophobicity compared to that of other fluoropolymers. In this study, plasma fluorination was performed using carbon tetrafluoride (CF₄) gas to improve anti-corrosion properties of PVDF. The fluorine content and hydrophobicity of PVDF were investigated in different CF₄ flow rates, followed by the determination of anti-corrosion properties. The fluorine content on the surface of the PVDF film increased by up to 46.70%, but the surface free energy was independent of CF₄ flow rate. Meanwhile, the surface roughness of the PDVF film tended to increase by up to 150% and then decrease with increasing CF₄ flow rate. It is considered that the plasma fluorination affects the surface free energy due to the introduction of fluorine functional groups and surface etching. In addition, the degree of corrosion of the PVDF-coated Fe plate was significantly reduced from 49.2% to 19.0% compared to that of the uncoated Fe plate. In particular, the degree of corrosion of the fluorinated PVDF-coated Fe plate was 13.6%, which was 28.4% lower than that of the PVDF-coated Fe plate, showing improved anti-corrosion protection.

• Membrane Journal
• /
• v.20 no.2
• /
• pp.106-112
• /
• 2010

This study deals with the surface fluorination of poly(phenylene oxide) (PPO) with the direct contact of 100 ppm fluorine gas. To characterize the surface fluorinated membranes, the contac angle measurement, X-ray photoelectron microscopy analysis and the gas permeation experiments were performed. As the fluorination time increases, the hydrophobicity of membrane surfaces is increased by the surface characterization. In general, as expected, the overall gas permeability was reduced. Typically, the permeability reduction of 33% for nitrogen, 23% for oxygen and 3% for carbon dioxide were observed when the membranes were exposed in 100 ppm environment for 60 min., meanwhile the selectivity was increased from 3.92 to 4.47 for $O_2/N_2$ and 18.09 to 25.4 for $O_2/N_2$, respectively.

• Membrane and Water Treatment
• /
• v.6 no.1
• /
• pp.27-42
• /
• 2015

In this study, poly (phenylene oxide) (PPO) and poysulfone (PSf) were sulfonated and aminated respectively. Both sulfonated poly (phenylene oxide) (SPPO) and aminated polysulfone (APSf) were characterized via the measurement of FT-IR, swelling degree, ion exchange capacity (IEC), and ion conductivity. Then the surfaces of these membranes were modified by surface fluorination using 2000 ppm $F_2$ gas against $N_2$ gas for 1 h at room temperature. The surface fluorinated SPPO and APSf membranes were characterized again to determine any differences between the pristine and fluorinated membranes. In total, 3 types of bi-polar membranes were prepared by varying the IEC of the APSf and having a fixed value for the IEC of the SPPO. The hypochlorite concentration generated by using the surface fluorinated membranes was dependent on the IEC of the APSf and ranged from 683 to 826 ppm, while there was a considerable improvement in the durability of the surface fluorinated membranes as they remained intact even after operating for 4 h.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.345-351
• /
• 2007

In this research, by using the fluorine gas, the poly(ether sulfone) (PES), the polysulfone (PSf), and the poly-vinylidenefluoride (PVDF) membranes were modified to improve the performance of the optional Gas-Liquid Contactor The SEM, surface contact angle, XPS, and the water transmission minimum pressure test was performed in order to examine the characteristics of which is surface modified. As a result of looking into the surface morphology of from the SEM measurement, we could know that the roughness of the membrane surface increased as the fluorine processing time increased. $-CH_2$, and the perfluoro group of $-CH_3$ were chemically combined with the surface fluorine conversion film surface and the hydrophobicity was exposed to be increased. Moreover, we could know that as the surface fluorinated processing time increased from the surface contact angle and water transmission minimum pressure test, the measured value increased and the overall characteristics were improved.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.540-546
• /
• 2010

In this manuscript, in order to reduce methanol permeability and, at the same time, to increase proton conductivity THS-PSA containing silica compound, responsible for methanol permeability reduction, and sulfonic acid, responsible for proton conductivity enhancement, was applied onto PVA/PSSA-MA membranes. And in order to improve durability, the resulting membranes, PVA/PSSAMA/THS-PSA, were exposed to 500ppm F2 gas at varying reaction times. The surface-fluorinated membranes were characterized through the measurement of contact angles, thermo-gravimetric analysis, and X-ray photoelectron spectroscopy to observe the physico-chemical changes. For the evaluation of the electro-chemical changes in the resulting membranes, its water contents, ion exchange capacity, proton conductivity, and methanol permeability were measured and then compared with the commercial membrane, Nafion 115. Finally, the membran electrode assembly(MEA) was prepared and the cell voltage against the current density was measured. As fluorination time increased, the contents of F2 increased up to maximum 4.3% and to depth of 50 nm. At 60 min of fluorination, the proton conductivity was 0.036 S/cm, larger than Nafion 115 at 0.024 S/cm, and the methanol permeability was $9.26E-08cm^2/s$, less than Nafion 115 at $1.17E-06cm^2/s$.