• Journal of Powder Materials
• /
• v.21 no.6
• /
• pp.407-414
• /
• 2014

The powder injection molding process having advantages in manufacturing three-dimensional precision parts essentially requires a debinding process before sintering to remove the binders used for preparing feedstock. In this study, powder injection molding of translucent alumina was performed, and carbon dioxide ($CO_2$) is used as a supercritical fluid that makes it possible to remove a large amount of binder, which is paraffin wax. The relationship between the optical property of translucent alumina and the debinding condition (temperature and pressure) of supercritical $CO_2$ was investigated. As temperature and pressure increased, extraction rate of the binder showed rising tendency and average grain size after sintering process was relatively fine. On the other hand, optical transmittance was reduced. As a result, the debinding condition at $50^{\circ}C$ and 20 MPa that represents the lowest extraction rate, $8.19{\times}10^{-3}m^2/sec$, corresponds to the largest grain size of $14.7{\mu}m$ and the highest optical transmittance of 45.2%.

• Fisheries and Aquatic Sciences
• /
• v.18 no.2
• /
• pp.123-130
• /
• 2015

Seaweed Sargassum horneri extracts were obtained using supercritical carbon dioxide ($SC-CO_2$) and different solvents. $SC-CO_2$ was kept at a temperature of $45^{\circ}C$ and pressure of 250 bar. The flow rate of $CO_2$ (27 g/min) was constant during the entire 2-h extraction period, and ethanol was used as a cosolvent. Six different solvents [acetone, hexane, methanol, ethanol, acetone mix methanol (7:3), and hexane mix ethanol (9:1)] were used for extraction and agitated by magnetic stirring (250 rpm) in the dark at $25^{\circ}C$ for 20 h; the ratio of material to solvent was 1:10 (w/v). Antioxidant properties of S. horneri extracted using $SC-CO_2$ with ethanol and different solvents have shown good activity. The highest activity belongs to $SC-CO_2$ with ethanol extracted oil, showing DPPH, ABTS, total phenolic content, and total flavonoid levels of $68.38{\pm}1.21%$, $83.51{\pm}1.25%$, $0.64{\pm}0.02mg/g$, and $5.57{\pm}0.05mg/g$, respectively. The S. horneri extracts showed a significant correlation between the antioxidant activity and phenolic content. Based on these results, the $SC-CO_2$ extract (ethanol) of the seaweed extract from brown seaweed may be a valuable antioxidant source.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.16-20
• /
• 2005

Porous polypropylene membranes were prepared by a thermally induced phase separation method in super-critical $CO_2$, where polypropylene and Camphene were used as raw materials. The porosity of polypropylene membranes with 10 wt% polypropylene concentration was 78, 80, 73% by using methanol, ethanol, and n-buthanol as an analytical solvent, respectively. The tensile strength increased with an increasing polypropylene concentration, where it was $0.17kg_f/mm^2$ at 10 wt% polypropylene concentration. The extraction rate for Camphene increased with time and Camphene was removed 94% in 5 min. It increased with an increasing temperature and was 99% at $45^{\circ}C$, however, decreased with an increasing temperature at higher than $45^{\circ}C$. The extraction rate increased with an increasing pressue up to 150 bar, however, decreased slightly with an increasing pressure over 150 bar. The extraction rate had a relation with the solubility of Camphene in supercritical $CO_2$.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1783-1786
• /
• 2016

The paper investigates the insulation properties of the supercritical $CO_2$ ($SCCO_2$) fluid as an insulating medium for electrical apparatuses. The insulating material is crucial for electrical apparatuses and $SF_6$ gas has been widely used for high power electrical apparatuses. There have been many research efforts to develop substituents for $SF_6$ gas because of high global warming potential. We obtained above 350 kV/mm insulation strength with 12.0 MPa $SCCO_2$. The positive and negative IEC standard pulses are applied between two 10 mm diameter spherical electrodes. The insulation strength of $SCCO_2$ is at least 2.5 times higher than that of $CO_2$ gas at 6.0MPa. The insulation strength of $SCCO_2$ fluid is about 10 times higher than that of $SF_6$ at 0.5MPa which is the ordinary operating pressure of electrical switchgears. Using the result, we expect that the time for switching and dielectric recovery could be reduced using $SCCO_2$ fluid as an insulating medium.

• Clean Technology
• /
• v.18 no.1
• /
• pp.38-42
• /
• 2012

Photonic crystals (PCs) are highly ordered porous materials which have been much attention because of its potential for controlling the light sauces. There are many methods for synthesizing this kind of materials among them we chose the supercritical deposition. With this method the reactants can easily infiltrate into the complex structure. In this paper, supercritical carbon dioxide ($scCO_2$) was used as a reaction medium, which is known as a sustainable solvent due to its nontoxic and noninflammable characteristics. We coated the colloidal template with metal alkoxide by using $scCO_2$ and then obtained macro-porous inverse opals. The reaction was carried out at $40^{\circ}C$ and 80 bar. We synthesized two different inverse opals which called silica and titania inverse opals by use of tetraethyl orthosilicate (TEOS) and titanium isopropoxide (TTIP) as a precursor, respectively.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.785-791
• /
• 2002

The effect of the supercritical carbon dioxide (sc$CO_2$) on ion-conductive behaviors for polyether electrolytes based on, both poly (ethylene oxide) (PEO) and poly [oligo (oxyethylene glycol) methacrylate] (PMEO) with lithium triflate, LiCF$_3$SO$_3$, has been investigated. In particular, the present research is a new concept for improving the ionic conductivity of polyether electrolytes. The maximum ionic conductivity ($\sigma$$_{max}$) at room temperature of the PEO electrolyte was more than 100 times higher, and the $\sigma$$_{max}$ at 9$0^{\circ}C$ of the PMEO electrolyte was 30 times improved by the se$CO_2$ treatment, respectively. It was revealed that the penetration of $CO_2$ molecules into the polymer matrix causes the increase of carrier ions by ion-dispersion effect and the decrease of glass transition temperature (T$_{g}$) by plasticizing effect that results in the improvement of the ion transport behaviors.viors.

• Korean Journal of Food Science and Technology
• /
• v.27 no.3
• /
• pp.414-419
• /
• 1995

${\beta}-carotene$ was extracted from freeze-dried carrot by supercritical carbon dioxide $(SC-CO_2)$ and mixtures of $CO_2$ doped with ethanol or methanol as a cosolvent at temperatures of 40 to $60^{\circ}C$ and pressures of 138 to 276 bar. Solubility of ${\beta}-carotene$ in $SC-CO_2$ increased with the increase of extraction pressure and the decrease of extraction temperature. The highest solubility observed was $4.90\;{\mu}g/g\;CO_2\;for\;{\alpha}-carotene\;and\;0.604\;{\mu}g/g\;CO_2$ for ${\alpha}-carotene\;at\;40^{\circ}C$ and 276 bar. Addition of ethanol increased the solubility being the largest increase of 82% using a mixture of $CO_2$ and 17.4% ethanol. $SC-CO_2$ extraction can be used to selectively obtain natural carotenoids, free of solvent residuals, which can be used as food additives.

• Macromolecular Research
• /
• v.16 no.2
• /
• pp.120-127
• /
• 2008

Glycidyl methacrylate linked poly(dimethylsiloxane) (GMA-PDMS) was synthesized and used as a stabilizer for the dispersion polymerization of methyl methacrylate (MMA) in supercritical $CO_2$. This study examined the effect of the concentrations of the stabilizer, 2,2'-azobisisobutyronitrile (AIBN) initiator, and MMA on the yield, molecular weight, and morphology of the poly(methyl methacrylate) (PMMA) product. PMMA was obtained in 94,6% yield using only 0,87 wt% GMA-PDMS, When the AIBN concentration was increased from 025 to 1.06 wt%, the molecular weight and particle size of the PMMA decreased from 56,600 to 21,600 and from 4.1 to $2.7{\mu}m$, whereas the particle size distribution increased from 1.3 to 1.9. The $M_n$ of the PMMA product ranged from 41,600 and 55,800 under typical polymerization conditions. The PMMA particle diameter ranged from 1.8 to $11.0{\mu}m$ and the particle size distribution ranged from 1.4 to 1.8.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.3
• /
• pp.41-46
• /
• 2017

This study aims to select suitable co-solvents and to obtain optimal process conditions in order to improve process efficiency and productivity through experimental results obtained under various experimental conditions for the etching and rinsing process using liquid carbon dioxide and supercritical carbon dioxide. Acetone was confirmed to be effective through basic experiments and used as the etching solution for MEMS-wafer etching in this study. In the case of using liquid carbon dioxide as the solvent and acetone as the etching solution, these two components were not mixed well and showed a phase separation. Liquid carbon dioxide in the lower layer interfered with contact between acetone and Mems-wafer during etching, and the results after rinsing and drying were not good. Based on the results obtained under various experimental conditions, the optimum process for treating MEMS-wafer using supercritical CO2 as the solvent, acetone as the etching solution, and methanol as the rinsing solution was set up, and MEMS-wafer without stiction can be obtained by continuous etching, rinsing and drying process. In addition, the amount of the etching solution (acetone) and the cleaning liquid (methanol) compared to the initial experimental values can be greatly reduced through optimization of process conditions.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.550-554
• /
• 2008

The synthesis of dimethyl carbonate (DMC) from methanol and supercritical carbon dioxide over $K_2CO_3/ZrO_2$ catalysts have been studied. The catalysts were prepared by impregnating $ZrO_2$ with an aqueous $K_2CO_3$ solution. The optimum calcination temperature to disperse K species on the $ZrO_2$ surface was found to be 673 K. Monoclinic $ZrO_2$ was not active, as itself, for the DMC production. However, when the $K_2CO_3$ was impregnated on the $ZrO_2$, the catalytic performance was improved. Besides the catalyst, $CH_3I$ was used as a promoter. The $CH_3I$ promoter as well as the $K_2CO_3/ZrO_2$ catalyst was found to take an important role to improve the production of DMC. The optimum quantities for the catalyst and the promoter were estimated. The effect of the catalyst and the promoter for the DMC synthesis from methanol and supercritical carbon dioxide was investigated and the reaction mechanism was proposed.