• 대한화학회지
• /
• 제56권1호
• /
• pp.28-33
• /
• 2012

The kinetics of ruthenium(III) chloride catalyzed oxidation of butanone and uncatalyzed oxidation of cyclohexanone by cerium(IV) in sulphuric acid medium have been studied. The kinetic rate law(I) in case of butanone conforms to the proposed mechanism. $$-\frac{1}{2}\frac{d[Ce^{IV}]}{dt}=\frac{kK[Ru^{III}][butanone]}{1+K[butanone]}$$ (1). However, oxidation of cyclohexanone in absence of catalyst accounts for the rate eqn. (2). $$-\frac{1}{2}\frac{[Ce^{IV}]}{dt}=\frac{(k_1+k_1K^'[H^+])[Ce^{IV}][Cyclohexanone]}{1+K_3[HSO_4^-]}$$ (2) Kinetics and activation parameters have been evaluated conventionally. Kinetically preferred mode of reaction is via ketonic and not the enolic forms.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제8권5호
• /
• pp.291-293
• /
• 2003

Batch reactors were employed to investigate the kinetics of cellulose hydrolysis under extremely low acid (ELA) and high temperature condition. The sawdust was pretreated by Auto-hydrolysis prior to the batch reaction. The maximum yield of glucose obtained from the batch reactor experiment was about 70% for the pretreated sawdust, this occurred at 210 and 22$0^{\circ}C$. The maximum glucose yield from the untreated sawdust was much lower at these temperatures, about 55%. The maximum yields of glucose from the lignocellulosics were obtained between 15th and 20th minutes after which gradual decrease was observed.

• Advances in materials Research
• /
• 제13권2호
• /
• pp.103-114
• /
• 2024

Zeolites are microporous materials that find applications in different fields due to their numerous interesting properties. This research investigated the effect of leaching on unheated Ifon kaolin in dilute hydrochloric acid and sulphuric acid. The hydrothermal method synthesized zeolite-X type, and the resulting sample was characterized using different techniques. The silica/alumina ratio in the synthesized sample was approximately 5.6, while Infrared spectra confirmed that the synthesized material was Zeolite-X. Based on the X-ray diffraction patterns, other phases were also formed in addition to zeolite-X crystals. Thermogravimetry results indicated that the synthesized zeolite was relatively stable below 500℃, so its weight loss was only 13% after heating to about 200℃. A differential thermal analyzer confirmed this amount of weight loss, and endothermic and exothermic reactions were also observed for the samples calcined respectively at 700 and 900℃. Based on Brunauer-Emmett-Teller (BET) analyses, samples at 700℃ showed slower adsorption-desorption isotherms, pore volume, and sizes than those at 900℃. These results have shown that leaching and calcination temperature significantly affect the type of zeolite produced.

• Advances in concrete construction
• /
• 제10권2호
• /
• pp.171-183
• /
• 2020

The main objective of this study is the assessment of the ability of limestone mortars to resist to different chemical attacks. The ability of polypropylene (PP) fibres waste used as reinforcement of these concrete materials to enhance their durability is also studied. Crushed sand 0/2 mm which is a fine limestone residue obtained by the crushing of natural rocks in aggregates industry is used for the fabrication of the mortar. The fibres used, which are obtained from the waste of domestic plastic sweeps' fabrication, have a length of 20 mm and a diameter ranging between 0.38 and 0.51 mm. Two weight fibres contents are used, 0.5 and 1%. The durability tests carried out in this investigation included the water absorption by capillarity, the mass variation, the flexural and the compressive strengths of the mortar specimens immersed for 366 days in 5% sodium chloride, 5% magnesium sulphate and 5% sulphuric acid solutions. A mineralogical analysis by X-ray diffraction (XRD) and a visual inspection are used for a better examination of the quality of tested mortars and for better interpretation of their behaviour in different solutions. The results indicate that the reinforcement of limestone mortar by PP fibres waste is an excellent solution to improve its chemical resistance and durability. Moreover, the presence of PP fibres waste does not affect significantly the water absorption by capillarity of mortar nether its mass variation, when exposed to chloride and sulphate solutions. While in sulphuric acid, the mass loss is higher with the presence of PP fibres waste, especially after an exposure of 180 days. The results reveal that these fibres have a considerable effect of the flexural and the compressive behaviour of mortar especially in acid solution, where a reduction of strength loss is observed. The mineralogical analysis confirms the good behaviour of mortar immersed in sulphate and chloride solutions; and shows that more gypsum is formed in mortar exposed to acid environment causing its rapid degradation. The visual observation reveals that only samples exposed to acid attack during 366 days have showed a surface damage extending over a depth of approximately 300 ㎛.

• 한국산림과학회지
• /
• 제41권1호
• /
• pp.1-6
• /
• 1979

1. 본시험(本試驗)은 당화기질(糖化基質)로 산오리나무재(材)를 묽은황산(黃酸)으로 전처리(前處理)한 후(後) Trichoderma viride 16374호균(號菌)에서 얻은 cellulase를 작용(作用)시켜 환원당(還元糖)을 생성(生成)할 수 있는 최적조건(最適條件)을 조사(調査)한 것이다. 즉(卽) 산오리나무(10~15년생(年生))의 톱밥을 전처리(前處理)할 때 황산농도(黃酸濃度) 0.3%, 0.6%, 0.9%, 1.2%, 1.5%로 구분(區分)하고 열압시간(熱壓時間)은 $1.5kg/cm^2$에서 15분(分), 30분(分), 45분(分), 60분(分)으로 각각(各各) 구분(區分) 처리(處理)하여 건조(乾燥)시킨것을 다시 $190^{\circ}C$에서 30분간(分間) 열처리후(熱處理後) 60mesh로 분쇄(粉碎)한 것을 당화기질(糖化基質)로 사용(使用)하였다. 그리고 cellulase 반응조건(反應條件)은 0.1M황산완충액(黃酸緩衝液)(pH 5.0) 50ml, 기질량(基質量) 0.5g, 고근효소액(盬析酵素液) 0.5ml를 100ml용(用) 삼각(三角) flask에 넣고 잘 혼합(混合)한 후(後) $40^{\circ}C$에서 96시간(時間) 반응(反應)시켜 이때 생성(生成)된 환원당량(還元糖量)을 조사(調査)하였다. 2. 고근효소액(盬析酵素液)의 조제(調製)는 밀기울액체진탕배양법(液體振盪培養法)에 의(依에) 하여 생성(生成)된 조효소액(粗酵素液)을 유안절포도(硫安飽和度)에 의(依)한 고근효소액(盬析酵素液)을 만들었다. 3. 환원당정량(還元糖定量)은 DNS법(法)에 의(依)하였다. 4. 묽은황산(黃酸)으로 처리(處理)한 톱밥의 환원당(還元糖) 생성량(生成量)은 황산농도(黃酸濃度) 1.5%, $1.5kg/cm^2$에서 열압시간(熱壓時間)은 45분(分)으로 처리(處理)한 것이 16.0%로 최대량(最大量)을 나타냈으나 작용(作用)함으로서 생성(生成)된 환원당량(還元糖量)은 황산농도(黃酸濃度) 0.9%, 열압시간(熱壓時間) 60분(分) 처리(處理)한 것이 23.6%로(본시험(本試驗) 범위(範圍)에서는 47.5% 증가(增加)) 나타났다.

• Advances in concrete construction
• /
• 제9권1호
• /
• pp.55-70
• /
• 2020

In this research article, acid resistance, sulphate resistance and sorptivity of self compacted concrete (SCC) prepared from C&D waste have been discussed. To improve the above properties of self compacted recycled aggregate concrete (SCRAC) along with mechanical and durability properties, different two stage mixing approaches (TSMA and TSMAsfc) were followed. In the proposed two stage mixing approach (TSMAsfc), silica fume, a proportional amount of cement and a proportional amount of water were mixed in premix stage which fills the pores and cracks of recycled aggregate concrete (RAC). The concrete specimen prepared using above mixing approaches were immersed in 1% concentration of sulphuric acid (H2SO4) and magnesium sulphate (MgSO4) solution for 28, 90 and 180 days for evaluating the acid resistance of SCRAC. Experimental results concluded that the proposed two stage mixing approach (TSMAsfc) is most suitable for acid resistance and sulphate resistance in terms of weight loss and strength loss due to the elimination of pores and cracks in the interfacial transition zone (ITZ). In modified two stage mixing approach, the pores and cracks of recycled concrete aggregate (RCA) were filled up and make ITZs of SCRAC stronger. Microstructure analysis was carried out to justify the reason of improvement of ITZs by electron probe micro analyser (EPMA) analysis. X-ray mapping was also done to know the presence of strength contributing elements presents in the concrete sample. It was established that SCRAC with modified mixing approach have shown improved results in terms of acid resistance, sulphate resistance, sorptivity and mechanical properties.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.101.1-101.1
• /
• 2015

플라즈마에 의한 식각 공정중 챔버 내에서 발생한 오염입자가 기판위에 떨어져 제품의 불량을 일으키고 그에 따른 부품 교체비용이나 교체시 가동을 멈춰야하는 문제점들이 있다. 이러한 문제점을 해결하기 위해 내플라즈마성이 우수하다고 알려진 아노다이징 피막을 사용하고 있다. 하지만 다양한 아노다이징 공법중 어떠한 요인이 내플라즈마 특성과 관계되는지에 대한 보고는 부족한 실정이다. 기존의 아노다이징 특성평가방법으로는 내화학 특성과 열안정성 평가, 구조적 특성을 확인하는 것이 주로 사용되어 왔다. 따라서 본 연구에서는 기존 내화학 특성과 열안정성이 우수하다고 알려진 황산-주석산법을 이용한 피막의 특성을 평가하여 내화학특성, 열적 안정성, 구조적 특성이 내플라즈마 특성과 어떠한 관계가 있는지 확인했다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.569-572
• /
• 2006

This study was performed to investigate the characteristics of carbonation for latex modified concrete with fly ash and blast furnace slag. The experimental variables consisted of ground granulated blast-furnace slag contents (0%, 30%, 50%), fly ash contents (0, 30%) latex contents (0, 5, 10, 15%). Two different methods of carbonation test such as $CO_2$ gas and 5% sulphuric acid digestion resistance test were varied in this study.

• 한국세라믹학회지
• /
• 제30권9호
• /
• pp.768-774
• /
• 1993

Sulphuric acid was intercalated in mesophase pitch based graphite fiber (Thornel P100 of Amoco), PAN based graphite fiber (M40 of Thoray) and PAN based carbon fiber (T300 ofThoray, TZ307 of Taekwang in Korea) by 0.4wt% CrO3/H2SO4 solution. The degree of crystallization of fibers increased P100, M40, TZ307, T300 fiber in order and their d002 values were 3.384, 3.424, 3.470, 3.493$\AA$, respectively. After intercalation P100 fiber formed 1 stage compound whose d002 value was 3.994$\AA$(d001=7.988$\AA$). Other fibers showed (002) reflection belonging to their 1 stage comound and prinstine fiber.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2001년도 추계학술대회 논문집
• /
• pp.321-322
• /
• 2001

대기중 과산화수소($H_2O$$_2$)는 기상과 액상에서 peroxy radicals 간의 결합 (HO$_2$ㆍ+ HO$_2$ㆍ $\longrightarrow$$H_2O$$_2$+O$_2$)에 의해 생성된다. 만약 수소 원자 하나가 organic group으로 치환되면 organic peroxides가 생성된다(Calvert et al., 1985). 이러한 과산화수소($H_2O$$_2$)와 methylhydroperoxide(MHP, $CH_3$COOH), hydroxymethylhydroperocide(HMHP, HOC$H_2O$OH)등의 organic peroxides는 대기 중에서 주요 산화제로 작용한다. 이들 peroxide 물질들은 pH 5 이하의 aqueous phase (cloud, fog and rain water)에서 sulphuric acid (HSO$_4$$^{2-}$ ) 형성에 중요한 역할을 한다(Calvert et al., 1985). (중략)