• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.905-912
• /
• 2006

Experiments in low strain rate methane-air counterflow diffusion flames diluted with $CO_2$ have been conducted to investigate the flame extinction behavior and edge flame oscillation in which flame length is less than the burner diameter and thus lateral conductive heat loss in addition to radiative loss could be remarkable at low global strain rates. The critical mole fraction at flame extinction is examined in terms of velocity ratio and global strain rate. It is seen that flame length is closely relevant to lateral heat loss, and this sheets flame extinction and edge flame oscillation considerably. Lateral heat loss causes flame oscillation even at fuel Lewis number less than unity. Edge flame oscillations are categorized into three: a growing-, a harmonic- and a decaying-oscillation mode. Onset conditions of the edge flame oscillation and the relevant modes are examined with global strain rate and $CO_2$ mole fraction in fuel stream. A flame stability map based on the flame oscillation modes is also provided at low strain rate flames.

• Nuclear Engineering and Technology
• /
• 제52권11호
• /
• pp.2479-2490
• /
• 2020

We performed experiments to measure a single-phase upward flow in a 5 × 5 rod bundle with spacer grids using a particle image velocimetry, focusing on the crossflow. The Reynolds number based on the hydraulic diameter and the bulk velocity is 10,000. The ratio of pitch between rods and rod diameter is 1.4 and spacer grid is installed periodically. The turbulence in the rod bundle results from the combination of a forced mixing and natural mixing. The forced mixing by the spacer grid persists up to 10D_h from the spacer grid, while the natural mixing is attributed to the crossflow between adjacent subchannels. The combined effects contribute to a sinusoidal distribution of the time-averaged stream-wise velocity along the lateral direction, which is relatively weak right behind the spacer grid as well as in the gap. The streamwise and lateral turbulence intensities are stronger right behind the spacer grid and in the gap. Based on these findings, we newly defined a modified mixing coefficient as the ratio of the lateral turbulence intensity to the time-averaged streamwise velocity, which shows a spatial variation. Finally, we compared the developed model with the measured data, which shows a good agreement with each other.

• 설비공학논문집
• /
• 제23권8호
• /
• pp.549-555
• /
• 2011

For a $CO_2$ one-stage twin rotary compressor, a T-shaped suction port was used to effectively supply the suction gas stream into two individual suction chambers of the twin cylinders. Suction gas pulsations were observed in the pressure sensor signals and these were simulated by using the acoustic modeling of Helmholz resonators in parallel. The module of acoustic modeling was combined to a computer simulation program for the compressor performance. Validation of the simulation program has been carried out for a bench model compressor in a compressor calorimeter. Cooling capacity and the compressor input power were reasonably well compared between the simulation and the calorimeter test. Particularly, good agreement on P-V diagram between the simulation and the test was obtained.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.74-75
• /
• 2021

In the recent 2017 annual average fine dust concentration (PM2.5) statistics released by the Organization for Economic Cooperation and Development (OECD), Korea has a high concentration of 25.14㎍/m3, which is about twice the average of 12.5㎍/m3 in OECD countries. Fine dust (PM2.5) is the main source of secondary pollutant production by the reaction of primary pollutants emitted from automobiles and thermal power plants, mainly composed of sulfates, nitrates, and organic carbon. The permeable block is an eco-friendly product that prevents rainwater from collecting on the surface of the road because it does not penetrate the groundwater properly, and is widely constructed on sidewalks or parking lots to recharge groundwater in case of rain. In addition, the pavement of the permeable block is a fundamental solution to reduce pollution by preventing rainwater from flowing into the stream, and it also has the advantage of easy replacement as well as low replacement costs. Therefore, this study was a basic experiment to produce permeable blocks mixed with TiO2 and diatomite to improve indoor air quality, and intended to analyze the flexural strength and compressive strength of permeable blocks mixed with TiO2.

• 한국산림과학회지
• /
• 제112권3호
• /
• pp.374-381
• /
• 2023

산지하천에서 발생하는 돌발홍수는 특정 지점의 점(Point) 유속보다는 전체 구간의 평균 유속에 따라 이동속도가 결정되며, 구간 평균유속은 하천경사, 하상재료, 수리적 거칠기에 많은 영향을 받는다. 이 연구에서는 하천경사 및 거칠기 높이를 이용하여 산지하천의 구간 평균유속 추정방법을 개발하였다. 염료추적자법(Dye Tracing)을 이용하여 특정 구간의 평균유속을 측정하고, LiDAR 영상으로부터 하천 지형 및 형상을 추출하였다. 거칠기 높이를 산정하기 위해 표면 거칠기 변수(R_a, R_max, R_z )와 하상재료의 크기(D₅₀, D₈₄)를 이용하였다. 현장 계측자료로부터 무차원 접근법을 이용하여 구간 평균유속과 유량과의 관계식 v = 0.5499Q^0.6165 을 도출하였으며, R² =0.77의 설명력을 나타냈다. 이 연구에 이용된 5개의 거칠기 높이 중 평균 거칠기 높이(R_a)의 RMSE가 0.45로서 다른 거칠기 높이의 범위(0.47-1.04)보다 낮게 나타나 평균 거칠기 높이(R_a)가 구간 평균유속 산정을 위한 거칠기 높이 인자로 가장 적합하다고 판단되었다.

• Wind and Structures
• /
• 제30권5호
• /
• pp.533-546
• /
• 2020

Large Eddy Simulation (LES) is used to study the effects of steady slot suction on the aerodynamic forces of and flow around a wall-mounted finite-length square cylinder. The aspect ratio H/d of the tested cylinder is 5, where H and d are the cylinder height and width, respectively. The Reynolds number based on free-stream oncoming flow velocity U_∞ and d is 2.78×10⁴. The suction slot locates near the leading edge of the free end, with a width of 0.025d and a length of 0.9d. The suction coefficient Q (= U_s/U_∞) is varied as Q = 0, 1 and 3, where U_s is the velocity at the entrance of the suction slot. It is found that the free-end steady slot suction can effectively suppress the aerodynamic forces of the model. The maximum reduction of aerodynamic forces occurs at Q = 1, with the time-mean drag, fluctuating drag, and fluctuating lift reduced by 3.75%, 19.08%, 40.91%, respectively. For Q = 3, all aerodynamic forces are still smaller than those for Q = 0 (uncontrolled case), but obviously higher than those for Q = 1. The involved control mechanism is successfully revealed, based on the comparison of the flow around cylinder free end and the near wake for the three tested Q values.

• Korean Chemical Engineering Research
• /
• 제43권4호
• /
• pp.467-473
• /
• 2005

액상의 아산화질소($N_2O$) 혼합물은 주요 불순물로써 공기, 일산화탄소, 수분, 이산화탄소와 NOx 성분을 포함하고 있다. 저온에서 고체화하여 고 순도의 $N_2O$를 얻어내는 것은 위험하다고 알려져 있다. 본 연구에서는 연속식 증류공정에 기초하여 고 순도의 $N_2O$ 제품을 얻어내는 새로운 방법을 소개하였다. 99.999％ 이상의 고 순도의 $N_2O$ 제품을 얻어낼 수 있는 연속식 증류공정을 모델화하기 위하여 intalox wire guaze 타입의 SCH-80S의 충진탑을 사용하였다. Peng-Robinson 상태방정식을 사용하여 연속식 증류탑과 냉동 사이클을 모사하였다. 본 연구에서 수행한 전산모사 결과는 상용성 화학공정모사기인 Aspen Plus로 모사한 결과와 매우 잘 일치함을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제23권6호
• /
• pp.640-646
• /
• 2012

The effect of Ce promotion over 1wt% $Pt/{\gamma}-Al_2O_3$ catalysts on the CO conversion and $CO_2$ selectivity was investigated in preferential CO oxidation (PrOx) to reduce the CO concentration less than 10 ppm in excess $H_2$ stream for polymer electrolyte membrane fuel cell (PEMFC). Ce-promoted 1wt% $Pt/{\gamma}-Al_2O_3$ catalysts were prepared by incipient wetness impregnation method and the loading amount of Pt was fixed at 1wt%. The content of Ce promoter which has excellent oxygen storage and transfer capability due to the redox property was adjusted from 0 to 1.5wt%. Ce-promoted 1wt% $Pt/{\gamma}-Al_2O_3$ catalysts exhibit high CO conversion and $CO_2$ selectivity at low temperatures below $150^{\circ}C$ due to the improvement of reducibility of surface PtOx species compared with the 1wt% $Pt/{\gamma}-Al_2O_3$ catalyst without Ce addition. When Ce content was more than 1wt%, the catalytic activity was decreased at over $160^{\circ}C$ in PrOx because of competitive $H_2$ oxidation. As a result, 0.5wt% Ce is optimal content not only to achieve high catalytic activity and good stability at low temperatures below $150^{\circ}C$ in the presence of $CO_2$ and $H_2O$ but also to minimize the $H_2$ oxidation at high temperatures.

• 한국재료학회지
• /
• 제20권3호
• /
• pp.111-116
• /
• 2010

Chloride-based fluxes such as NaCl-KCl are used in the refining of Al melt. The vapor pressure of the chloride is one of the fundamental pieces of information required for such processes, and is generally high at elevated temperatures. In order to measure the vapor pressure for chlorides, the apparatus for the transpiration method was assembled in the present study. The vapor pressure of $ZnCl_2$ and $FeCl_2$, which is related with the process of aluminum refining and the recovery of useful elements from iron and steel industry by-products, was also measured. In the measurement of vapor pressure by the transpiration method, the powder of $ZnCl_2$ or $FeCl_2$ in a alumina boat was loaded in the uniform zone of the furnace with a stream of Ar. The weight loss of $ZnCl_2$ and $FeCl_2$ after holding was measured by changing the flow rate of Ar gas (10 sccm -230 sccm), and the partial pressures of $ZnCl_2$ and $FeCl_2$ were calculated. The partial pressures within a certain range were found to be independent of the flow rate of Ar at different temperatures. The vapor pressures were measured in the temperature range of 758-901K for $ZnCl_2$ and 963-983K for $FeCl_2$. The measured results agreed well with those in the literature.

• The Korean Journal of Ecology
• /
• 제22권3호
• /
• pp.101-108
• /
• 1999

지형요인이 어떻게 수질에 영향을 주는가를 연구하고자 1993년 3월 부터 1998년 3월까지 조사를 실시하였다. 조사지는 충북 옥천군 이원면의 경작지가 주류를 이루는 개심저수지와 산지유역으로 특성지워지는 장찬저수지 유역을 대상으로 하였다. 조사유역을 11개 소집수역으로 세분하고 지형학적 특성과 하천수질과의 상관성, 하천 유역의 오염원 동태를 생태학적 관점에서 규명하고자 조사를 실시하였다. 개심저수지 유역의 형상계수는 0.030∼0.210(평균 0.090), 장찬저수지 유역의 형상계수는 0.217∼0.452 (평균 0.325)로 장찬저수지 유역의 형상계수가 3.61배 더 높다. 개심저수지의 E(지정리와 미동리), F(윤정리) 소집수역은 금강유역 전체의 형상계수 0.063과 비슷하여 홍수유속시간이 금강과 유사하였다. 하천길이와 유역면적의 관계식은 L=1.44A/sup 0.06/로 보정되었다. 환상율은 개심저수지 유역 17.114, 장찬저수지 유역 7.444로, 강수도달시간은 금강 전체 유역보다 5배 빠른 것으로 추정되었다. 세장율은 개심저수지 유역 0.357 (금강 0.282), 장찬저수지 0.636으로 나타나 장찬저수지 유역에서 강수집합시간이 1.54배 더 빠른 것으로 나타났다. 각 집수역별 강수도달시간은 장찬저수지 유역의 A' 소집수역이 337.53 min.로 가장 느렸으며 개심저수지 유역의 H 소집수역은 49.26 min.로 가장 빠른 것으로 나타났는데, 대체적으로 하류로 갈수록 강수집합시간이 빠른 것으로 나타났다. 곡의 밀도는 0.500∼l.337범위에 있었으며 강수침투와는 역의 상관을 나타낸다. 따라서 인위적으로 하천을 막거나 개절(開切), 직선배수로화는 홍수를 유발할 가능성이 많고, 하천의 자정능력을 떨어뜨리는 결과를 낳을 것으로 판단되었다. 개심저수지와 장찬저수지의 수계빈도(Df)와 곡의 밀도(Dd)의 관계는 개심저수지 유역 Df=0.023Dd², 장찬저수지유역 Df=0.189Dd²으로 산정되었다. 평균경사는 개심 14.03, 장찬 16.9로서 장찬저수지가 유량이 많아지기 쉬운 것으로 조사 되었다. 경사가 증가하면 용존산소량은 증가하지만, 증가폭은 크질 않은 것으로 나타났다. COD와 평균경사는 유의한 상관이 없었으나 BOD는 평균경사와 유의한 상관이 있는 것으로 조사되었다. 형상계수와 환상률 및 총질소와의 관계는 형상계수(Y/sub TKN/=0.7271X＋0.0967)와 환상률이 커질수록 TKN이 증가하였다. (Y/sub TKN/=0.1577X-0.1501). BOD와 COD는 1BOD/l.2COD의 관계가 있었다.