• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.28-33
• /
• 2005

A resource recovery technique using sub- and supercritical water hydrolysis was applied to recover amino aicds from waste fish entrails. The effect of reaction parameters such as temperature and time necessary for the control of reaction towards optimum yield of amino acids was investigated using semi-batch and batch reactors. Results showed a maximum yield of total amino acids (137 mg/g-dry entrails) from waste fish entrails at T=$250^{\circ}C$ (P=4 MPa) and reaction time of 60 min in a batch reactor. Under supercritical conditions (e.g., T=$400^{\circ}C$, P=45 MPa), the yield decreased due to rapid decomposition compared to production rate of amino acids. As a result, the low temperature and the short reaction time were needed to produce a maximum yield of amino acids.

• Textile Coloration and Finishing
• /
• v.31 no.1
• /
• pp.48-64
• /
• 2019

With evolution in the production environment of the textile industry, the need for non-water-based dyeing technologies and eco-friendly process facilities in the dyeing and processing stages has increased. In recent years, supercritical fluid dyes have been developed and commercialized in Europe, centering on this demand. However, so far, such dyes have been mainly applied in the processing of PET fibers. Basic research has mainly involved investigation of dyeing by supercritical carbon dioxide or solubility of such dyes, and more in-depth research should be continuously carried out. In this review, we describe the types and characteristics of supercritical fluids that exhibit specific properties at pressures and temperatures over the critical point. In addition, the state of the art in the dyeing and processing technology using supercritical fluids and associated, processing problems, environmental regulation, and wastewater treatment issues are described in detail. We hope this review can contribute to the supercritical fluid technology being further developed as an environment friendly dyeing processing method. Furthermore, we expect that the technique can be used as a means of ensuring different, high-quality dyed products.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.6
• /
• pp.44-50
• /
• 2006

To characterize thermo-chemical feature of su gar conversion of woody biomass poplar wood (Populus alba${\times}$glandulosa ) by sub- and supercritical water was treated for 60s under subcritical (23 MPa, 325 and $350^{\circ}C$) and supercritical (23 MPa, 380, 400, and $425^{\circ}C$) conditions, respectively. Among degradation products undegraded poplar wood solids existed in aqueous products. As the treatment temperature increased, the degradation of poplar wood was enhanced and reached up to 83.1% at $425^{\circ}C$. The monomeric sugars derived from fibers of poplar wood by sub- and supercritical treatment were analyzed by high performance anionic exchange chromatography (HPAEC). Under the subcritical temperature ranges, xylan, main hemicellulose component in poplar wood, was preferentially degraded to xylose, while cellulose degradation started at the transition zone between sub and supercritical conditions and was remarkably accelerated at the supercritical condition. The highest yield of monomeric sugars amounts to ca. 7.3% based on air dried wood weight (MC 10%) at $425^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.220-224
• /
• 2017

In this study, we investigated a new recycling method of phenol resin, which is widely used to make electric insulation boards and adhesives, into carbon particles by using supercritical fluids. Because phenol resin is insoluble and infusible, most of the phenol resin wastes are buried in the ground or incinerated, which leads to environmental pollution. Therefore, development of a new method to recycle phenol resin waste is an urgent issue. In this study, phenol resin waste was treated with four sub/supercritical solvents: ethanol, acetone, water, and methanol. For all the sub/supercritical solvents, the phenol resin wastes were broken down into carbon nano particles at much lower temperatures than that required in the existing carbon particle manufacturing processes. We investigated the difference of morphologies and physical properties of recycled carbon particles according to the use of various solvents. As a result, carbon nano particles with the same amorphous structure were obtained from phenol resin waste with the usage of various sub/supercritical solvents at much lower temperature.

• Journal of Life Science
• /
• v.18 no.2
• /
• pp.213-219
• /
• 2008

Flavonoids in pine needles are known to be effective scavengers of free radical. Especially, proanthocyanidin, a kind of flavonoids possesses cardiovascular protection and antioxidative activities. Here, we evaluated proanthocyanidin contents in total polyphenolic compounds of pine needle extracts prepared by using hot water, ethanol, hexane or sub-supercritical $CO_2$. Analyses of total polyphenolic compounds and proanthocyanidin in each extracts indicated that hot water extract contained the highest concentrations, but sub-supercritical extract contained the lowest concentrations. On the other hand, evaluation of proanthocyanidin contents in total polyphenolic compounds in each extracts showed that sub-supercritical extract possessed the highest content, but hot water extract possessed the lowest content. These results indicate that extracts containing high concentrations of both total polyphenolic compounds and proanthocyanidin could be obtained by using hot water or ethanol extractions. Furthermore, extract containing high content of proanthocyanidin out of total polyphenolic compounds could be achieved by using sub-supercritical extraction. Measurement of antioxidative activities of extracts showed that hot water extract possessed the highest activity. In this study, we prepared extracts from pine needles by four different methods and evaluated the antioxidative compounds in extracts that could be used for effective components of functional food products.

• The Korean Journal of Food And Nutrition
• /
• v.36 no.4
• /
• pp.264-273
• /
• 2023

Physicochemical properties and storage stability of plant-based alternative meat prepared with low-fat soybean powder (LPAM) treated by supercritical-CO₂ and those of full-fat soybean powder (FPAM) were compared. Ash and crude protein contents were higher in LPAM than in FRAM. Water absorption capacity and oil absorption capacity were significantly higher in LPAM than in FPAM. Water binding capacity was higher in LPAM than in FPAM during a 20 days storage period at 5℃ and pH was significantly lower in LPAM than in FPAM after a 5~10 days storage period. Hardness, gumminess and chewiness significantly increased with the increase in the storage period, and the three were significantly higher in LPAM than in FPAM after 10 days and 20 days of storage. The acid value showed no remarkable difference according to the storage period in LPAM; however, it was significantly higher in FPAM than in LPAM after 20 days of storage. The peroxide value and TBA value were significantly increased according to the storage period, and were significantly lower iin LPAM than in FPAM during all the storage periods. Therefore, the use of low-fat soybean powder may be effective in improving oxidative stability during storage in the production of plant-based alternative meat.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.292-295
• /
• 2008

In a SCWR (SuperCritical pressure Water cooled Reactor), the coolant temperature initially at below the pseudo-critical temperature at the bottom of a reactor core increases as the coolant flows upward through the sub-channels of the fuel assemblies, and it finally becomes higher than the pseudo-critical temperature when it leaves the reactor core. At certain conditions, heat transfer deterioration occurs near the pseudo-critical temperature and it may cause a drastic rise of the fuel surface temperature resulting a fuel failure. Therefore, an accurate estimation of the heat transfer coefficient is very important for the thermal-hydraulic design of a reactor core. An experiment on heat transfer to the vertically upward flowing $CO_2$ at a supercritical pressure in a circular tube were performed at KAERI. The internal diameter of the test section is 6.32 mm, which corresponds to the hydraulic diameter of a sub-channel in the conceptional design proposed by KAERI. The test range of the mass flux is 285 to 1200 kg/m$^2$s and the maximum heat flux is 170 kW/m$^2$. The inlet pressure is maintained at 8.12 MPa, which is 1.1 times the critical pressure. A new correlation, which covers both the normal and deterioration heat transfer regimes was proposed and compared with the estimations by exiting correlations.

• Korean Journal of Food Science and Technology
• /
• v.52 no.5
• /
• pp.516-523
• /
• 2020

Supercritical carbon dioxide (_SCO2) extraction was applied for the defatting of mealworm to prepare defatted powder (DP) and protein isolate (PI) and compare the process to press and hexane extraction, with respect to DP and PI physicochemical properties. _SCO2 DP was obtained by extracting 34.40% oil at 41.37 MPa, 40℃ for 180 min, and the product contained 71.66% crude protein, which is similar to that of hexane DP and higher than that of press DP. In using alkali protein extraction to prepare PI from DP, _SCO2 was as effective as hexane and better than press. _SCO2 produced brighter DP and PI than press, but not as much as hexane. Protein solubility was similar in all DP, with minimum values at pH 5. The highest water adsorption capacity was noticeable for _SCO2 PI, and _SCO2 DP showed an oil adsorption capacity comparable to that of hexane DP. _SCO2 DP and PI had better foaming capacity than press DP and PI and showed superior emulsion activity compared to others.

• Journal of Soil and Groundwater Environment
• /
• v.21 no.3
• /
• pp.35-48
• /
• 2016

A micromodel was applied to estimate the effects of geological conditions and injection methods on displacement of resident porewater by injecting scCO₂ in the pore scale. Binary images from image analysis were used to distinguish scCO₂-filled-pores from other pore structure. CO₂ flooding followed by porewater displacement, fingering migration, preferential flow and bypassing were observed during scCO₂ injection experiments. Effects of pressure, temperature, salinity, flow rate, and injection methods on storage efficiency in micromodels were represented and examined in terms of areal displacement efficiency. The measurements revealed that the areal displacement efficiency at equilibrium decreases as the salinity increases, whereas it increases as the pressure and temperature increases. It may result from that the overburden pressure and porewater salinity can affect the CO₂ solubility in water and the hydrophilicity of silica surfaces, while the neighboring temperature has a significant effect on viscosity of scCO₂. Increased flow rate could create more preferential flow paths and decrease the areal displacement efficiency. Compared to the continuous injection of scCO₂, the pulse-type injection reduced the probability for occurrence of fingering, subsequently preferential flow paths, and recorded higher areal displacement efficiency. More detailed explanation may need further studies based on closer experimental observations.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.842-848
• /
• 2022

Parametric studies of heat transfer and fluid flow are very important research of interest because the design and operation of fluid flow and heat transfer systems are guided by these parametric studies. The safety of the system operation and system optimization can be determined by decreasing or increasing particular fluid flow and heat transfer parameter while keeping other parameters constant. The parameters that can be varied in order to determine safe and optimized system include system pressure, mass flow rate, heat flux and coolant inlet temperature among other parameters. The fluid flow and heat transfer systems can also be enhanced by the presence of or without the presence of particular effects including gravity effect among others. The advanced Generation IV reactors to be deployed for large electricity production, have proven to be more thermally efficient (approximately 45% thermal efficiency) than the current light water reactors with a thermal efficiency of approximately 33 ℃. SCWR is one of the Generation IV reactors intended for electricity generation. High Performance Light Water Reactor (HPLWR) is a SCWR type which is under consideration in this study. One-eighth of a proposed fuel assembly design for HPLWR consisting of 7 fuel/rod bundles with 9 coolant sub-channels was the geometry considered in this study to examine the effects of system pressure and mass flow rate on wall and fluid temperatures. Gravity effect on wall and fluid temperatures were also examined on this one-eighth fuel assembly geometry. Computational Fluid Dynamics (CFD) code, STAR-CCM+, was used to obtain the results of the numerical simulations. Based on the parametric analysis carried out, sub-channel 4 performed better in terms of heat transfer because temperatures predicted in sub-channel 9 (corner subchannel) were higher than the ones obtained in sub-channel 4 (central sub-channel). The influence of system mass flow rate, pressure and gravity seem similar in both sub-channels 4 and 9 with temperature distributions higher in sub-channel 9 than in sub-channel 4. In most of the cases considered, temperature distributions (for both fluid and wall) obtained at 25 MPa are higher than those obtained at 23 MPa, temperature distributions obtained at 601.2 kg/h are higher than those obtained at 561.2 kg/h, and temperature distributions obtained without gravity effect are higher than those obtained with gravity effect. The results show that effects of system pressure, mass flowrate and gravity on fluid flow and heat transfer are significant and therefore parametric studies need to be performed to determine safe and optimum operating conditions of fluid flow and heat transfer systems.