• Fashion & Textile Research Journal
• /
• v.6 no.3
• /
• pp.399-403
• /
• 2004

Education of clothing and textiles in the university is various according to the purposes. Among that clothing construction and practice is what is needed the most in understanding the process of apparel producing, and is the basic subject of areas from apparel designs to quality management. Producing apparel starts from planning the bodice pattern according to the human body shape. Basic bodice pattern should be highly practical so that production of all items of apparel patterns can be possible. Also, a basic bodice pattern needs to be planned in the way that even beginners can use it by classifying sizes according to each body measurements. Thus in this study. bodice patterns will be produced in way of draping method subjecting university students in early 20s. standardized and classified sizes will be calculated from it and bodice pattern made by studied flat pattern method will be examined and compared so that finally suitability will be compared. As a result of examining and comparing bodice patterns made by draping method and studied flat pattern method on the model of the human body produced by plaster method, sizes were classified into 5 levels. As a result of evaluation of creation. satisfying consequence from various body shape was acquired and it is expected of the beginners who are stating from clothing construction and practice to be educated by using the result of this study.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.950-955
• /
• 2003

The fluid propulsion mechanism of two oscillating flat plates is studied numerically using a discrete vortex method. Presently, the flat plates are assumed to be rigid. To analyze the closely coupled aerodynamic interference between the flat plates, a core addition scheme and a vortex core model are combined together. A calculated wake pattern for a flat plate in heaving oscillation motion is compared with the flow visualization. The effect of wake shapes on the aerodynamic characteristics of the flat plate in pitching oscillation is investigated. The velocity profiles behind the flat plates in pitching oscillations are plotted to investigate the possible thrust generation mechanism.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.548-550
• /
• 2010

The droplet motion on a flat substrate with contact angle hysteresis is studied by solving the equations governing the conservation of mass and momentum. The liquid- gas interface is determined by an level-set method which is based on a sharp-interface representation for accurately imposing the matching or coupling conditions at the interface. The method is modified to treat the dynamic contact angle at the liquid-gas-solid interface. The computations are performed to investigate a droplet impact and merging pattern on a flat substrate to find a optimal condition in a micro-line patterning process. The effects of dynamic contact angles on droplet motion are quantified.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.103-108
• /
• 2009

The droplet impact and merging process on a flat substrate with contact angle hysteresis is numerically studied. The droplet deformation is determined by an improved level-set method employing a sharp-interface technique for the stress condition at the liquid-gas interface and the contact angle condition at the liquid-gas-solid interline. Based on the computations, the droplet impact and merging pattern is investigated to find the optimal condition in manufacturing a micro-line. The effects of dynamic contact angles and droplet spacing on droplet motion are quantified.

• Fisheries and Aquatic Sciences
• /
• v.2 no.2
• /
• pp.210-217
• /
• 1999

Chemical oxygen demand (COD), phytoplankton cell number and chlorophyll-a concentration (Chl-a), sediment mean grain size and ignition loss were studied to determine their temporal trends in the study area. Historical data of COD, cell number and Chl-a were gathered from the late 1960s or early 1980s to 1997, and trends in temporal domain were obtained from a simple regression. Sediments for grain size and ignition loss (as organic contents in sediments) were sampled from the Chokchon macrotidal flat bimonthly from September 1990 to November 1996, and were analyzed using the decomposition method of time series analysis. In general, the first three data showed increasing trends based on regression analysis. The trends of sediment grain size fluctuated in a neutral pathway while those of ignition loss yielded no increasing pattern. In contrast with the suggestions from Ahn and Choi (1998) who reported a coarsening variation in sediment grain size to be a cause of the directional and remarkable changes of macrofaunal communities in this area, we could not find such a corresponding variation pattern from our samples. In diagnosing eutrophication, a paradoxical phenomenon was encountered between the trends in water column (COD, cell number and Chl-a) and sediment (ignition loss) data. In this paper, we inferred the possible processes that produce the discrepancy. Some explanations and biological responses to eutrophication were predicted and discussed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.6
• /
• pp.650-655
• /
• 2011

Analysis of two-dimensional Rayleigh wave scattering pattern by a surface defect is studied through modified boundary element method. BEM proposed in this paper has special treatment at each end of boundary which should have the Rayleigh wave go away without any generation of virtual reflections. It is shown that treatment for truncated boundary which is used to model two-dimensional Rayleigh waves' behavior in an elastic half-space is successfully implemented. To check numerical results' accuracy, time domain IFFT signal of the displacements is presented. Improvement on getting rid of unwanted influence of truncated boundary induced by 2-D Rayleigh waves on a flat surface of an elastic half-infinite medium is shown. As a final goal, the numerical results of Rayleigh wave scattering trend are plotted and they are compared with theoretical curves to prove its accuracy.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.510-520
• /
• 2019

To investigate the morphology characteristics of air layer in the air cavity, a numerical method with the combination of RANS equations and VOF two-phase-flow model is proposed for a plate with air cavity. Based on the model above, the dynamic and developmental process of air layer in the air cavity is studied. Numerical results indicate that the air layer in the plate's air cavity exhibits the dynamic state of morphology and the wavelength of air layer becomes larger with the increasing speed. The morphology of air layer agrees with the Froude similarity law and the formation of the air layer is not affected by the parameters of the cavity, however, the wave pattern of the air layer is influenced by the parameters of the cavity. The stable air layer under the air cavity is important for the resistance reduction for the air layer drag reduction.

• Steel and Composite Structures
• /
• v.13 no.4
• /
• pp.367-382
• /
• 2012

This paper is dedicated to the buckling behaviors of strengthened perforated plates under edge shear loading, which is a typical load pattern of steel plates in civil engineering, especially in plate and box girders. The square plates considered each has a centric circular hole and is simply supported on four edges in the out-of-plane direction. Three types of strengthening stiffeners named ringed stiffener (RS), flat stiffener (FSA and FSB) and strip stiffener (SSA, SSB and SSC) are mainly discussed. The finite element method (FEM) has been employed to analyse the elastic and elasto-plastic buckling behavior of unstrengthened and strengthened perforated plates. Results show that most of the strengthened perforated plates behave higher buckling strengths than the unstrengthened ones, while the enhancements in elastic buckling stress and elasto-plastic ultimate strength are closely related to stiffener types as well as plate geometric parameters including plate slenderness ratio and hole diameter to plate width ratio. The critical slenderness ratios of shear loaded strengthened perforated plates, which determine the practical buckling pattern (i.e., elastic or elasto-plastic buckling) of the plates, are also studied. Based on the contrastive analyses of strengthening efficiency considering the influence of stiffener consumption, the most efficient cutout-strengthening methods for shear loaded perforated square plates with different slenderness ratios and circular hole diameter to plate width ratios are preliminarily identified.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.432-432
• /
• 2007

We studied optical simulation method for ultra slim backlight system. We designed 0.7mm thickness light guide plate and combined 48 white color LEDs for 12 inch wide size TFT-LCD. We designed flat shape PMMA light guide plate with both side patterned. It have vertical prism shape on upper side and ellipse dot pattern on the other side. We targeted 4500 nit brightness and uniform emission characteristic without hot spot or dark area. At first, we designed uniform emission area with more high brightness in center area and then, debugged light entering hot spot zone and direction of outgoing light flux. Although it was designing step, we obtained good result with reverse prism optical sheet and it had good repeatability because it was based on the stamper method in injection process without laser engraving or micro groove engraving method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.3
• /
• pp.346-359
• /
• 2012

This study provides basic guidelines to enrich lecture content and teaching methods for university lecturers about basic clothing construction (flat pattern making). The survey was conducted from October $13^{th}$ to December $20^{th}$ 2010 by mail and e-mail on 96 selected clothing departments in Korean universities to investigate the content, method and condition of the course of basic pattern making. A total of 63.3% of survey respondents were PhD graduates, 80 percent majored 'Apparel Science and Technology', average of total teaching experience was 12.84 years and 40 percent had studied abroad. The surveyed universities were 4 year universities (70%), 2-3 year tenure colleges (27%), and Cyber Universities (3%). The average number of students in a class was 28.08 and the lab space and equipment was evaluated positively only when the number of students was 20 or less. The type of measurements for basic pattern drafting were 'individual student's sizes' (62%), 'ready-made clothes sizing system' (25%), 'professor's experiential sizes' (5%), 'dress form sizes' (3%). In addition, the percentage of using 'ready-made clothes sizing system' increased 13% over the previous study (Lee, 2000). At a basic pattern drafting stage, 'the error of body measurements' in the case of using individual student's sizes, 'the poor results of fitting for students who deviate from standard body size' in the case of using ready-made clothes sizing system, 'the lack of education about fitting' in the case of using dress form sizes had been pointed out as shortcomings. A total of 66% of survey respondents carried out muslin fitting; however, a lack of students and teacher feedback about fitting & alteration of paper patterns remained a problem.