• Steel and Composite Structures
• /
• v.15 no.3
• /
• pp.281-298
• /
• 2013

Composite special moment frame is one of the systems that are utilized in areas with low to high seismicity to deal with earthquake forces. Composite moment frames are composed of reinforced concrete columns (RC) and steel beams (S); therefore, the connection region is a combination of steel and concrete materials. In current study, a three dimensional finite element model of composite connections is developed. These connections are used in special composite moment frame, between reinforced concrete columns and steel beams (RCS). Finite element model is discussed as a most reliable and low cost method versus experimental procedures. Based on a tested connection model by Cheng and Chen (2005), the finite element model has been developed under cyclic loading and is verified with experimental results. A good agreement between finite element model and experimental results was observed. The connection configuration contains Face Bearing Plates (FBPs), Steel Band Plates (SBPs) enveloping around the RC column just above and below the steel beam. Longitudinal column bars pass through the connection with square ties around them. The finite element model represented a stable response up to the first cycles equal to 4.0% drift, with moderately pinched hysteresis loops and then showed a significant buckling in upper flange of beam, as the in test model.

• Computers and Concrete
• /
• v.20 no.1
• /
• pp.11-22
• /
• 2017

There are two methods to model the plastification of members comprising lumped and distributed plasticity. When a reinforced concrete member experiences inelastic deformations, cracks tend to spread from the joint interface resulting in a curvature distribution; therefore, the lumped plasticity methods assuming plasticity is concentrated at a zero-length plastic hinge section at the ends of the elements, cannot model the actual behavior of reinforced concrete members. Some spread plasticity models including uniform, linear and recently power have been developed to take extended inelastic zone into account. In the aforementioned models, the extended inelastic zones in proximity of critical sections assumed close to connections are considered. Although the mentioned assumption is proper for the buildings simply imposed lateral loads, it is not appropriate for the gravity load effects. The gravity load effects can influence the inelastic zones in structural elements; therefore, the plasticity models presenting the flexibility distribution along the member merely based on lateral loads apart from the gravity load effects can bring about incorrect stiffness matrix for structure. In this study, the linear flexibility distribution model is improved to account for the distributed plasticity of members subjected to both gravity and lateral load effects. To do so, a new model in which, each member is taken as one structural element into account is proposed. Some numerical examples from previous studies are assessed and outcomes confirm the accuracy of proposed model. Also comparing the results of the proposed model with other spread plasticity models illustrates glaring error produced due to neglecting the gravity load effects.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.2 no.2
• /
• pp.67-74
• /
• 1990

A numerical model is developed to predict the shoreline change by the coastal structures constructed. In order to describe the wave deformation at the shadow zone of the structure, the present model employs the mild-slope equation in steady state and the wave ray method using the coefficients of wave refraction, diffraction and shoaling. In the model results of shoreline changes for the various structures. it showed a qualitative agreement with the findings observed in the field such as tombolo, and the response of this model was found to be very sensitive to the longshore distribution of wave heights. It was also applied to a field area. From the results of the application this model is proved to be useful around the complex coastal structures and bottom topography.

• Earthquakes and Structures
• /
• v.23 no.6
• /
• pp.549-580
• /
• 2022

This paper assesses the influences of modeling assumptions and uncertainties on the performance of the non-linear finite element (FE) model updating procedure and model clustering method. The results of a shaking table test on a four-story steel moment-resisting frame are employed for both calibrations and clustering of the FE models. In the first part, simple to detailed non-linear FE models of the test frame is calibrated to minimize the difference between the various data features of the models and the structure. To investigate the effect of the specified data feature, four of which include the acceleration, displacement, hysteretic energy, and instantaneous features of responses, have been considered. In the last part of the work, a model-based clustering approach to group models of a four-story frame with similar behavior is introduced to detect abnormal ones. The approach is a composition of property derivation, outlier removal based on k-Nearest neighbors, and a K-means clustering approach using specified data features. The clustering results showed correlations among similar models. Moreover, it also helped to detect the best strategy for modeling different structural components.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.192-200
• /
• 2010

Korea is part of a region of low or moderate seismic zone in which few earthquakes have been monitored, so it is difficult to approve design ground motions and seismic responses on structures from response spectrum. In this study, a series of dynamic centrifuge model tests for demonstrating seismic amplification characteristics in soil-foundation-structure system were performed using electro-hydraulic shaking table mounted on the KOCED 5.0 m radius beam centrifuge at KAIST in Korea. The soil model were prepared by raining dry sand and $V_S$ profiles were determined by performing bender element tests before shaking. The foundation types used in this study are shallow embedded foundation and deep basement fixed on the bottom. Total 7 building structures were used and the response of building structures were compared with response spectrum from the acceleration records on surface.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.2
• /
• pp.100-108
• /
• 1995

Heat transfer plays a critical role in determining interface location and shape in ZMR process, which is used for the fabrication of silicon - on - insulator structure. In this work, the two - dimensional pseudo - steady - state ZMR model has been developed that can simulate the heat transfer process during ZMR process. It contains the radiation, convection and conduction heat transfer and determines the interface shapes. Numerical solutions from the model include flow field in the molten zone, temperature field in the full SOl structure and the location of solid/liquid interface in the silicon thin film and silicon substrate. We examined the effects of the various system parameters on the temperature profiles and the interface shape.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.3
• /
• pp.578-588
• /
• 1992

In order to predict the effect of swirl on the structure of concentric laminar jet diffusion flame, present study examined the effect of swirl on the flame characteristics by numerical numerical analysis through theoretical model. The theoretical model has been developed for the co-axial laminar jet flame such that the fuel and air are supplying with swirl through inner and outer co-axial tube respectively. For the parametric study, swirl number, Reynolds number of fuel and air and directions of swirl are chosen as important parametes. The results of study show that the flame with width and shorter length is formed by larger swirl number. The important factor of the flame shape is the recirculating zone formed around jet axis near the exit of nozzle. In case of weak swirl, the effect of directions of swirl is not appeared. However, for the strong swirl, the flame with shorter length are appeared in case of counter-swirl compared with the case of co-swirl.

• The Journal of the Petrological Society of Korea
• /
• v.10 no.2
• /
• pp.106-120
• /
• 2001

The Busan area in the northeastern part of the Ogcheon metamorphic zone, Korea, consists mainly of Precambrian Busan and Bakdallyeong gneiss complexes, Ogcheon metamorphic rocks and Mesozoic granitoids. The Busan gneiss complex shows Heart-shaped distribution laying down eastward, and is surrounded by the Ogcheon metamorphic rocks in the central part of the Busan area. In this study structural examination on the main constituent rocks (Busan gneiss complex and Ogcheon metamorphic rocks) was conducted to clarify the geological structure of the Ogcheon metamorphic zone in the Busan area. It indicates that the geological structure was formed at least by three phases of deformation. (1) Dl deformation: the formative period of the structural units of WNW trend (Sanjeoteo, Busan-II, Busan-I, and Chungiu nappes) and the mylonitic foliations related to the compression of NNE-SSW direction, (2) D2 deformation: the differential E-W shortening and N-S extension period of the structural units of WNW trend related to the compression of E-W or WNW-ESE directions, (3) D3 deformation: the formative period of the kink or open folds of E-W trend related to the compression of N-S direction in the eastern and southern parts of Busan area where the structural units of N-S or NNE trends reoriented owing to the intense D2 deformation were developed. These three phases of deformation are closely connected with the distribution of the structural units and the Heart-shaped Busan gneiss complex laying down eastward, and in this paper a new geodynamic model to the Heart-shaped Busan gneiss complex is suggested: Dl deformation-the zonal distribution of WNW trend with a constant width, D2 deformation - the formation of convex wedges northeastward and southward, D3 deformation - the formation of concave wedge westward.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.2
• /
• pp.184-193
• /
• 2008

The gate expansion was planed to increase discharge capacity of gate structure at sea dike in Asan Bay. So it was estimated for changing of hydraulic states in Pyeongteak Harbor Zone caused by gate expansion, using Delft3D, FLOW-3D and hydraulic physical scale model testing. In result, the influence of gate expansion was indicated to be weak.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.38-41
• /
• 2009

Debonding behavior of symmetric tilt bicrystal interfaces with <100> misorientation axis is investigated through molecular dynamics simulations. FCC single crystal copper is considered in each grain and the model is idealized as a grain boundary under mechanical loading. Embedded-Atom Method potential is chosen to calculate the interatomic forces between atoms. Constrained tensile deformations are applied to a variety of misorientation angles in order to estimate the effect of grain boundary angle on local peak stress. A new parameter of symmetric grain-boundary structure is introduced and refines the correlation between grain boundary angle and local peak stress.