• Transactions on Electrical and Electronic Materials
• /
• v.5 no.4
• /
• pp.133-137
• /
• 2004

The development of digital x-ray detector has been extensively progressed for the application of various medical modalities. In this study, we introduce a new hybrid-type x-ray detector to improve problems of a conventional direct or indirect digital x-ray image technology, which composed of multi-layer structure using a CaWO$_4$ phosphor and amorphous selenium (a-Se) photoconductor. The leakage current of our detector was found to be ∼180 pA/cm$^2$ at 10 V/m, which was significantly reduced than that of a single a-Se detector. The x-ray sensitivity was measured as the value of 4230 pC/cm$^2$/mR at 10 V/m. We found that the parylene thin film between a CaWO$_4$ phosphor and an a-Se layer acts as an insulator to prevent charge injection from indium thin oxide (ITO) electrode into an a-Se layer under applied bias.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.5
• /
• pp.11-17
• /
• 2012

In this study, a damage detection method that uses sensitivity-based finite (FE) element model updating with the natural frequency and zero frequency was proposed. The stiffness matrix for a structure was modified using the sensitivity-based FE model updating method. A sensitivity analysis was used to update the FE model, and the natural frequencies and zero frequencies were considered as target parameters to supplement the information on the vibration characteristics. The locations and values of the damages were estimated from the modified stiffness matrix. Several numerical examples were considered to verify the performance of the proposed method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.326-332
• /
• 1997

Recently to develop an automobile with better prosperities, many researches and investments have been executed. In this paper we intend to improve the automobile properties by reducing the weights of the engine without changing the dynamic characteristics. At first we perform the vibration analysis by the Substructure Synthesis Method and execute the exciting test for the engine model, and observe the coincidences of two results to confirm the reliability of the analyzing tools used. The weight minimization is performed by the Sensitivities of the Natural frequencies of the engine block. To decrease the engine weight ideally, the parts of the sensitivity zero are to be cut mainly, and the changing quantity of natural frequency by the cut is to be recovered by the structural modification for the parts with the good sensitivity. But, as actually the mathematical solution for the homogeneous problem(i.e. 0 object function) do not exist, we hereby redesign the block with much thinner thickness and recover the natural frequencies and natural modes to original structure's by the sensitivity analysis. And the Frequency Response Functions(FRF) are to be observed for the interesting points. In this analysis, the original thickness of the engine model has 8 mm of thickness, and the thickness redesigned is 5 mm and 6 mm. And we are to try to recover the 1, 2, 4, and 5 lower natural frequencies interested.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3612-3624
• /
• 2021

At present, in the case of pump fast optimization, there is a problem of rapid, accurate and effective prediction of cavitation performance. In "A Cavitation Performance Prediction Method for Pumps PART1-Proposal and Feasibility" [1], a new cavitation performance prediction method is proposed, and the feasibility of this method is demonstrated in combination with experiments of a mixed flow pump. However, whether this method is applicable to vane pumps with different specific speeds and whether the prediction results of this method are accurate is still worthy of further study. Combined with the experimental results, the research evaluates the sensitivity and accuracy at different flow rates. For a certain operating condition, the method has better sensitivity to different flow rates. This is suitable for multi-parameter multi-objective optimization of pump impeller. For the test mixed flow pump, the method is more accurate when the area ratios are 13.718% and 13.826%. The cavitation vortex flow is obtained through high-speed camera, and the correlation between cavitation flow structure and cavitation performance is established to provide more scientific support for cavitation performance prediction. The method is not only suitable for cavitation performance prediction of the mixed flow pump, but also can be expanded to cavitation performance prediction of blade type hydraulic machinery, which will solve the problem of rapid prediction of hydraulic machinery cavitation performance.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.3
• /
• pp.87-93
• /
• 2018

Ground source heat pump(GSHP) system is one of the high efficiency heat source systems which utilizes the constant geothermal energy of a underground water or soil. However, the design of conventional GSHP system in the domestic market is dependent on the experience of the designer and the installer, and it causes increase of initial installation cost or degradation of system performance. Therefore, it is necessary to develop a guideline and the optimal design method to maintain stable performance of the system and reduce installation cost. In this study, in order to optimize the GSHP system, design factors according to ground heat exchanger(GHX) type have been examine by simulation tool. Furthermore, the design factors and the correlation of a single U-tube and a double U-tube were analyzed quantitatively through sensitivity analysis. Results indicated that, the length of the ground heat exchanger was greatly influenced by grout thermal conductivity for single U-tube and pipe spacing for double U-tube.

• Korean Journal of Remote Sensing
• /
• v.27 no.6
• /
• pp.761-771
• /
• 2011

The sensitivity of microwave scattering to the dielectric properties and the geometric structure of soil surfaces makes radar remote sensing a challenge for a wide range of environmental issues directly related to the condition of natural surfaces. Especially, the potential for retrieving soil moisture with a high spatial and/or temporal resolution represents a significant contribution to hydrological and ecological modeling. This paper aims to review the current state of the art in SAR technology and methodological issues towards the discovery of a new potential accurate monitoring of soil moisture changes. In this paper, important parameters or constraints significantly affect the sensitivity of the measurements to soil moisture, such as roughness statistics, spatial resolution, and local topography, are discussed to improve the applicability of SAR remote sensing techniques. This study particularly intends to discuss important notes for developing smart and reliable methods capable of retrieving geophysical information.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.244-249
• /
• 1994

The dynamic characteristics of mechanical structure are strongly affected by the properties of joint parameters. In this study, the test structures are constructed with two beam structures which are clamped by bolts, and a bolted joint which is modelled as a lumped stiffness element. To identify the dynamic joint parameters with variance of clamping torque of bolts, the sensitivity analysis and the mode energy analysis methods are investigated experimentally. As a result of these two methods, stiffnesses of bolted joint are experimentally found to increase as the clamping torque increases. These stiffnesses identified from the sensitivity analysis and the mode energy analysis method have some difference.

• Journal of the Korean Magnetic Resonance Society
• /
• v.15 no.2
• /
• pp.157-174
• /
• 2011

Although the use of apodization functions in connection with postprocessing of a 2D NMR spectrum proves improved spectral quality, there is usually a trade-off between resolution enhancement and noise suppression due to a classical "uncertainty principle." In this study, therefore, a mathematical deconvolution technique called "Maximum Likelihood Deconvolution (MLD)" was adopted to achieve the spectral resolution and sensitivity enhancement simultaneously. The MLD technique greatly facilitates visualization and restoration of the genuine spectral information from complex 2D NMR spectra that would be problematic with the conventional apodization/FT processing. In particular, application of the MLD to the 2D-NOE spectrum would be very useful to derive the important proton connectivities, which are essential to achieve elucidating the 3D molecular structure.

• Journal of Sensor Science and Technology
• /
• v.19 no.2
• /
• pp.92-98
• /
• 2010

The capacitive sensor has a simple structure, compact size and low cost, but a small dynamic range. The small range is caused by use of gap variation. If the sensor takes area variation type with one plate moving horizontally, it can have a large measurable range. While the area variation has relatively low sensitivity, some studies have found methods to improve the sensitivity. Even though the methods are effective, parameters of the results are limited and 2 dimensional. This study provides more practical and 3 dimensional analysis and suggests relations between parameters. Using the results, the optimized design parameters of a high dynamic range capacitive sensor can be found.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.256-259
• /
• 2004

In the present study, AZ31B sheets has a bad formability in room temperature, but the formability is improved significantly as increasing the temperature because of rolled magnesium alloy sheet has a hexagonal closed packed structure (HCP) and a plastic anisotropy. In this paper, after tensile test in various temperatures, strain rate, show the tensile mechanical properties, yield and ultimate strength, K-value, work hardening exponent(n), strain rate sensitivity(m). As temperature increased, yield, ultimate strength and K-value, work hardening exponent(n) are decreased but strain rate sensitivity(m) is increased. As cross-head-speed increased, yield, ultimate strength and K-value, work hardening exponent(n) are increased. And according to the temperature, how change the plastic anisotropy factor R. In addition, we observed how temperatures and cross-head-speed effect on microstructure.