• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.563-566
• /
• 2013

We investigated the variation of anion exchange membrane of hydrogen generator of alkaline electrolysis. We detected the variation of elements and change of anion exchange membrane using EDS and FE-SEM. We detected two different sites of membrane because of different structure of membrane. $Sp_1$ shows that the distribution ratio of C, O, Al is 98% very higher than $Sp_2$ of 78%. Especially, the main elements of STS316 which is P, S, Fe, Ni were more detected at $Sp_2$ than $Sp_1$. We think that this result depends on the structure of membrane. This also affect the resistance, lifetime of membrane and decrease the efficiency of hydrogen production. We hope that this article is a foundation of developing of hydrogen production technology.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.3
• /
• pp.265-270
• /
• 2004

Experiment study on a down scaled two-phase catalytic reactor is presented. As a preliminary step for the development of catalytic reactor, nano-particulate catalyst was prepared. Perovskite La$\_$0.8/Sr$\_$0.2/CoO$_3$is chosen and synthesized as a catalyst considering superior catalytic performance in reduction and oxidation process where oxygen is involved among the reagent. Reactor that has a scale of 2${\times}$10${\times}$25mm was made by machining of A1 block as a layered structure considering further extension to micro-machining. Hydrogen peroxide of 70wt% was adopted as reactant and was provided to the reactor loaded with 1.5 g of catalyst. Reactant flow rate was varied by precision pump with a range of 0.15cc/min to 17.2cc/min. Temperature distribution within reactor was recorded by 3 thermocouples and total amount of liquid product was measured. Temperature distribution and factors that affect temperature were observed and relation between temperature distribution and production rate was also analyzed. Relative time scale plays a significant role in the performance of the reactor. To obtain steady state operation, appropriate ratio of flow rate, catalyst mass and reactor geometry is required and furthermore to get more efficient production rate temperature distribution should be evenly distributed. The database obtained by the experiment will be used as a design parameter for micro reactor.

• The Journal of Industrial Distribution & Business
• /
• v.12 no.9
• /
• pp.31-42
• /
• 2021

Purpose: After the reform and opening up, China's overall economic development has entered a new era. From mutual investment and trade transactions between domestic provinces and regions to investment and trade with foreign companies, the continuous supplement of investment funds makes the follow-up development of all aspects of economic development smoother and has played a strong impetus. effect. Foreign direct investment has many influences on the economic development of a country or region. Research design, data and methodology: This article uses the sample data of Shandong Province from 2011 to 2019 to analyze the foreign direct investment in Shandong Province by industry, region, method and other aspects, and study the relationship and influence between foreign direct investment and economic growth. Results: The results show that there is a relatively close relationship between foreign direct investment and economic growth, and it has played a role in promoting economic development in many aspects such as industrial structure, foreign trade, and employment. Conclusions: At the same time, corresponding suggestions are put forward based on the analysis and conclusions drawn.

• Geomechanics and Engineering
• /
• v.29 no.2
• /
• pp.145-154
• /
• 2022

Complex geological conditions have a great influence on the mining of coalbed methane (CBM), which affects the extraction efficiency of CBM. This investigation analyzed the complicated geological conditions in the Liujia CBM block of Fuxin. A geological model of heterogeneities CBM reservoirs was established to study the influence of strike direction of igneous rocks and fault structures on horizontal well layout. Subsequently, the dual-porosity and dual-permeability mathematical model was established, which considers the dynamic changes of porosity and permeability caused by gas adsorption, desorption, pressure change. The results show that the production curve is in good agreement with the actual by considering gas seepage in matrix pores in the model. Complicated geological structures affect the pressure expansion of horizontal wells, especially, the closer to the fault structure, the more significant the effect, the slower the pressure drop, and the smaller the desorption area. When the wellbore extends to the fault, the pressure expansion is blocked by the fault and the productivity is reduced. In the study area, the optimal distance to the fault is 70 m. When the horizontal wellbore is perpendicular to the direction of coal seam igneous rock, the productivity is higher than that of parallel igneous rock, and the horizontal well bore should be perpendicular to the cleat direction. However, the well length is limited due to the dense distribution of igneous rocks in the Liujia CBM block. Therefore, the horizontal well pumping in the study area should be arranged along the direction of igneous rock and parallel plane cleats. It is found that the larger the area surrounded by igneous rock, the more favorable the productivity. In summary, the reasonable layout of horizontal wells should make full use of the advantages of igneous rock, faults and other complex geological conditions to achieve the goal of high and stable production.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.7
• /
• pp.1020-1027
• /
• 2015

The combined effect of tumbling marination methods (vacuum continuous tumbling marination, CT; vacuum intermittent tumbling marination, IT) and effective tumbling time (4, 6, 8, and 10 h) on the water status and protein properties of prepared pork chops was investigated. Results showed that regardless of tumbling time, CT method significantly decreased the muscle fiber diameter (MD) and significantly increased the total moisture content, product yield, salt soluble proteins (SSP) solubility, immobilized water component (p<0.05) compared with IT method. With the effective tumbling time increased from 4 h to 10 h, the fat content and the MD were significantly decreased (p<0.05), whereas the SSP solubility of prepared pork chops increased firstly and then decreased. Besides, an interactive effect between CT method and effective tumbling time was also observed for the chemical composition and proportion of immobilized water (p<0.05). These results demonstrated that CT method of 8 h was the most beneficial for improving the muscle structure and water distribution status, increasing the water-binding capacity and accelerating the marinade efficiency of pork chops; and thus, it should be chosen as the most optimal treatment method for the processing production of prepared pork chops.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.2
• /
• pp.232-242
• /
• 2017

The objective of this study was to examine changes in the porosity and internal structure of wood as it goes through the process of saccharification (extraction of fermentable sugars). This study also examined the use of different drying methods to prepare samples for characterization of internal pores, with particular emphasis on the partially disrupted cell wall. Aspen wood flour samples after dilute acid pretreatment followed by enzymatic hydrolysis were examined for nitrogen adsorption. The resulting isotherms were analyzed for surface area, pore size distribution, and total pore volume. Results showed that freeze drying (with sample pre-freezing) maintains the cell wall structure, allowing for examination of saccharification effects. Acid pretreatment (hemicellulose removal) doubled the surface area and tripled the total volume of pores, which were mostly 10-20 nm wide. Subsequent enzymatic hydrolysis (cellulose removal) caused a 5-fold increase in the surface area and a ~ 11-fold increase in the total volume of pores, which ranged from 5 to 100 nm in width. These results indicate that nitrogen adsorption analysis is a feasible technique to examine the internal pore structure of lignocellulosic residues after saccharification. The information on the pore structure will be useful when considering value-adding options for utilizing the solid waste for biofuel production.

• Journal of Industrial Technology
• /
• v.37 no.1
• /
• pp.32-36
• /
• 2017

In this study, as part of a research on the development of economical high-performance concrete with high strength and high quality, the physical properties of high-performance concrete were analyzed by substituting a certain amount of low-cost domestic silica fume exempted from the re-importation type distribution structure of the domestic production and the existing high-priced silica fume distribution structure. Performing tests to identify the physical properties of the fresh and hardened concrete and durability analogy of the concrete which use low-cost domestic silica fume and imported silica fume, the chloride ion penetration resistance test result showed that the strength difference between the low-cost silica fume and the imported silica fume is not big but the strength of the low-cost silica fume was measured higher than the imported silica fume. The chloride ion penetration resistance of all variables was measured as "very low". Since the low-cost domestic silica fume can be used as a high-performance admixture of concrete, the results suggest that it is possible to produce a more economical high-performance concrete.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2154-2159
• /
• 2007

The potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes was evaluated experimentally and computationally. With nitrogen-diluted premixed ethylene-air flames established on the Nickel-coated stainless steel double-faced wall, the propensities of carbon nanotube formation were experimentally determined using SEM and FE-TEM images and Raman spectroscopy, while the flame structure was computationally predicted using a 3-dimensional CFD code with a reduced reaction mechanism. The uniformity and yields of synthesized carbon nanotubes were evaluated in terms of the flame stretch rates. Results show substantial increase of area on the wall surface where uniform carbon nanotubes are synthesized with using the double-faced wall stagnation flow burner due to enhanced uniformity of temperature distribution along the wall surface and support the potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes.

• Journal of Distribution Science
• /
• v.13 no.4
• /
• pp.35-43
• /
• 2015

Purpose - This study aims to seek various plans to maintain the advancement of the overseas and domestic employment scenario through a case analysis of the Japanese industry, which maintains domestic employment while promoting the overseas advancement of companies despite having a similar industrial structure as Korea. The study further intends to derive insightful implications for Japanese manufacturing companies and government policies. Research design, data, and methodology - We selected four companies from the Japanese manufacturing industry. Being companies that were successful in increasing the domestic employment scenario while advancing in overseas markets. We utilized several secondary data sources including Japanese newspapers and report literature. Results - Previous studies have shown a negative relationship between Foreign Direct Investment (FDI) or offshoring and domestic employment. However, our results showed this relationship with respect to the Japanese manufacturing industry as follows: 1. FDI for developing overseas markets does not decrease domestic production. If Japanese companies change their strategy from exports to overseas production, there will be a consequent decrease in domestic employment of Multinational Enterprises (MNEs). However, the local production that plans the sales expansion of a foreign market does not substitute domestic production. 2. Several case studies illustrate that, as the production of final goods is expanded in foreign countries, there is a corresponding increase in the export of intermediary goods from Japan. In this case, if the production process of Japanese companies is promoted in foreign markets, the amount of exported material and parts from Japan will consequently increase. 3. It is difficult to consider that the establishment of subsidiary companies in foreign countries by manufacturing companies for wholesale, retail, and services decreases domestic employment. This is because the international development of these industries needs expatriates, expatriate training organizations, and research and development (R&D) activities. 4. When there is overseas demand, the growth of local management activities is expected to increase the work of the overseas business department in the head office in Japan, if competitiveness can be secured for better localization and management speed. 5. The conversion of the domestic manufacturing industry into high value-added production is necessary. The relocation of domestic production to foreign markets decreases domestic employment. To prevent this, the upgradation of domestic production bases, including high value-added production, and R&D capability need to be strengthened. Technology-based companies must develop new technology, patents, processes, and so forth, which require extensive human resources for R&D. Conclusions - Domestic medium-sized companies that are capable of consistently supplying high value-added products should be actively encouraged to deploy into and develop overseas markets. Further, this paper considers the necessity of a guidance policy that provides suggestions for overseas deployment, by the initiation of the government, to companies that cannot do so due to the lack of foreign experience or decisions by the CEO, despite having the relevant capability and technologies to supply high value-added products.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.101-106
• /
• 2002

Requirements to fabrication processes for arc welding of highly loaded thick-walled joint and problems of research and development in term s of the tendency for the modern aircraft structure development are outlined. A justified, choice of the development line of the new promising welding processes for solution of these problems is presented. A complex of new welding processes and technologies for making highly reliable joints with different thickness (up to 120 mm and more) and length of weld (up to 0.1 m; 0.1-0.5 m and more than 0.5 m) has bee developed. It is shown that the possibility to control the heat flow distribution over the groove surface of the welded joints provides for improved reliability. The new welding processes are equipment are effectively used in serial production of the Mykoyan md Sukhoi supersonic aircrafts as well as in AN-124 Ruslan and AN-225 Mriya wide body aircrafts.