• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.333-337
• /
• 2003

The use of reactive shearing structural intensity to place small patches of constrained layer damping material in order to achieve the largest reduction in the radiated sound power of Air-conditioner outdoor unit is described. The normal surface velocity of each panel was measured using a laser doppler vibrometer. Experimental results indicated that patches of constrained layer damping material placed over areas of high reactive structural intensity reduced the radiated sound power significantly more than patches of the same area placed over areas of low reactive structural intensity

• International Journal of Aerospace System Engineering
• /
• v.6 no.1
• /
• pp.1-7
• /
• 2019

In the present study, structural safety and stability on the main wing and tail planes of the 1.2 ton WIG(Wing in Ground Effect) flight vehicle, which will be a high speed maritime transportation system for the next generation, was performed. The carbon-epoxy composite material was used in design of wing structure. The skin-spar with skin-stressed structural type was adopted for improvement of lightness and structural stability. As a design procedure for this study, the design load was estimated with maximum flight load. From static strength analysis results using finite element method of the commercial codes. From the stress analysis results of the main wing, it was confirmed that the upper skin structure between the second rib and the third rib was unstable for the buckling load. Therefore in order to solve this problem, three stiffeners at the buckled region were added. After design modification, even though the weight of the wing was a little bit heavier than the target weight, the structural safety and stability was satisfied for design requirements.

• Journal of Aerospace System Engineering
• /
• v.1 no.2
• /
• pp.13-20
• /
• 2007

Structural qualification plan (SQP) for aerospace vehicle is based on material certification methodology, which must be approved by certification authority. It is internationally required to use of statistically based material allowables to design aerospace vehicles with aerospace materials. In order to comply with this regulation, it is necessary to establish relatively large amount of database, which increases test costs and time. Recently NASA/FAA develop the new methodology which results in cost, time, and risk reduction, and satisfies the regulation at the same time. This paper summarizes the certification methodology of materials system as a part of structural qualification plan (SQP) of aerospace vehicles and also thermal management of the vehicle system, like thermal protection materials system and thermally conductive material system. Materials design allowable was determined using this method for a carbon/epoxy composite material.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.529-532
• /
• 2008

Recently the compound material has interested in using the structural material as the bridge member assembly. It is the lighter material against existing construction material and has excellent durability and economy. The existing floor of bridge has its short period to repair and replace compared to other parts of the bridge with the pavement and the shoe. These deteriorations of usage and safety by aging and corrosion are needed frequent maintenance. The use of compound material as a structural member suggests solve these problems. So this thesis evaluates the static and the fatigue performance for whether there are fiber lamination direction and stress concentration section of FRP floor plate, the compound material.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.3
• /
• pp.411-419
• /
• 2023

In this paper, NIMONIC 86 material was tried to apply to exhaust valve for small-sized marine diesel engine. The both structural stability and thermal resistance in high temperature were needed to use the NIMONIC 86 material as exhaust valve for small-sized marine diesel eng ine. The purpose of this study is to investig ate the application of NIMONIC 86 material to exhaust valve of small-sized marine diesel engine by comparing, respectively, SUH 3 and STS 316 materials. As the results, NIMONIC 86 material has intermediate characteristics between SUH 3 and STS 316 materials in terms of the strength in condition of room temperature. Further NIMONIC 86 material was evaluated to have better characteristics than SUH 3 and STS 316 materials in terms of the thermal conductivity.

• Journal of the Korea Furniture Society
• /
• v.20 no.4
• /
• pp.358-373
• /
• 2009

Probability based design(PBD)method has some advantages against current design methods. First, it can provide the quantitative values for the structural safety or capacity through the reliability index, $^{\beta}$. That presented the certainty on the corresponding structure for the designer or user, also that permitted the broad consideration in the safety of structures. In addition, it can give the quantitative lifetime of the related structure in the calculation process of target reliability index. Also, incidental economical efficiency can be expected because decrease of required structural material can be obtained by using the practical material data. Unlikely current deterministic structural design methods, main advantage is the reflection of real condition in the structural design process by application of the data with not small clear specimen but structural size material. Advanced countries, namely America, Canada, Europe, Australia and New Zealand already converted from allowable stress design(ASD) method to PBD method and used as a standard wooden structures code in the late 1980s and 1990s. Other domestic constructions standards such as the steel or concrete constructions accepted and used the PBD methods already. Accordingly, wooden structural design method also should be converted from deterministic ASD to probabilistic LRFD(Load and resistance factor design) in order to keep pace with worldwide demands for PBD. Hence, to suggest the reason of introduction the PBD in domestic wooden structural design and analysis, a brief example was used to show the different reliability index by using the different design methods. Definition, merits and demerits of deterministic ASD and probabilistic LRFD were followed. Also the three examples were presented to show the similarity and differences between ASD and LRFD. Finally, connection problems that might cause a disputation in wooden structural design and analysis were broadly examined.

• Structural Engineering and Mechanics
• /
• v.42 no.4
• /
• pp.489-505
• /
• 2012

In this study, it is aim to perform the construction stage analysis of suspension bridges using time dependent material properties. Fatih Sultan Mehmet Suspension Bridge connecting the Europe and Asia in Istanbul is selected as an example. Finite element models of the bridge are modelled using SAP2000 program considering project drawing. Geometric nonlinearities are taken into consideration in the analysis using P-Delta large displacement criterion. The time dependent material strength variations and geometric variations are included in the analysis. Because of the fact that the bridge has steel structural system, only prestressing steel relaxation is considered as time dependent material properties. The structural behaviour of the bridge at different construction stages has been examined. Two different finite element analyses with and without construction stages are carried out and results are compared with each other. As analyses result, variation of the displacement and internal forces such as bending moment, axial forces and shear forces for bridge deck and towers are given with detail. It is seen that construction stage analysis has remarkable effect on the structural behaviour of the bridge.

• Advances in Computational Design
• /
• v.7 no.3
• /
• pp.173-188
• /
• 2022

In modern buildings, glass is considered a structurally unsafe material due to its brittleness and unpredictable failure behavior. The possible use of structural glass elements (i.e., floors, beams and columns) is generally prevented by its poor tensile strength and a frequent occurrence of brittle failures. In this study an innovative modelling based on an equivalent thickness concept of laminated glass beam reinforced with FRP (Fiber Reinforced Polymer) composite material and of glass plates punched is presented. In particular, the novel numerical modelling applied to an embedding Carbon FRP-rod in the interlayer of a laminated structural glass beam is considered in order to increase both its failure strength, together with its post-failure strength and ductility. The proposed equivalent modelling of different specimens enables us to carefully evaluate the effects of this reinforcement. Both the responses of the reinforced beam and un-reinforced one are evaluated, and the corresponding results are compared and discussed. A novel equivalent modelling for reinforced glass beams using FRP composites is presented for FEM analyses in modern material components and proved estimations of the expected performance are provided. Moreover, the new suggested numerical analysis is also applied to laminated glass plates with wide holes at both ends for the technological reasons necessary to connect a glass beam to a structure. Obtained results are compared with an integer specimen. Experimental considerations are reported.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.167-175
• /
• 2018

This research deals, The characteristics of mechanics and behavior of the tube structural systems, It has been investigated and considered conventional theory and case models, It has shown the suitability, The best location, And optimal shape of the unit module system, Considered variables materials of stiffness increase and decrease in hybrid tube structural systems this study carried out adapting analysis of statistical concepts. In a concrete way, This study exams the effect of reducing horizontal displacement and the shear lag phenomenon, Also, The purpose of this study is to utilize the basic data on the design and study of future high-rise hybrid structural system using this research. As a result, The framed- tube structural system does not effectively cope with horizontal behavior of high-rise buildings, The results of using varying material tested resistance factors and lateral loads in hybrid tube structural system, When each material is compared Bracing material is identified as a key factor in lateral behavior. In a ratio of material quantity framed-tube structural system, The level of sensitivity affecting the horizontal displacement is greater then the beam's column, In case of braced tube structural system, Braced appeared to be most sensitive in comparison of material quantity ratio in columns and beams.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.145-152
• /
• 2003

This paper develops a relatively comprehensive and sophisticated constitutive model of concrete for finite element analysis of concrete structures. The present model accounts for the hydrostatic pressure sensitivity and Lode angle dependence behavior of concrete, not only in its strength criterion, but also in its hardening characteristics. The implementation is carried out through incorporating the developed concrete model in User Subroutine Material(UMAT) of the general-purpose FE program ABAQUS(v.5.8). It is found that the model can sufficiently predict the hardening as well as the softening behaviour of concrete under high confining pressure.