• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.694-699
• /
• 2011

This paper compares the performance of lightning shielding analysis methods using the seven striking distance formulae in substation. For comparison, we evaluate the number of expected strikes and exposed area using WinIGS Software. Seven striking distance formulae are compared using the electrogeometric model analysis and the rolling sphere method. Based on the electrogeometric model analysis, the risk of shielding failure in either the whole substation or parts of it is determined. According to the simulation results, one can justify whether the substation satisfies the criterion of shielding design. In particular, according to the rolling sphere method, the exposed areas in substation determine the location of the additional shielding poles or shield wires. Therefore, the installation of the additional shielding poles and shield wires in substation was accepted by shield design at the phase conductors exposed in the larger area.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1288-1293
• /
• 2014

This paper proposes a new method to estimate the striking velocity for ballistic limit velocity in MIL-STD-662F. The method from MIL-STD-662F needs relative air density, drag coefficient, form factor, ballistic coefficient for estimating striking velocity. So precedent studies are essential. However, the new method can estimate striking velocity only using measured velocities and distance between the screen and the target. To prove new method, we compared estimation of striking velocity from both the new method and the method from MIL-STD-662F on the basis of datain PRODAS. The new method shows bigger errors in some velocity ranges. But it could still calculate ballistic limit velocity. It also shows smaller errors in most velocity ranges.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.950-958
• /
• 2017

Viaduct increases the height of subway catenary, namely magnifies lightning attraction scope that lead to higher possibility of suffering lightning stroke. Therefore, it is necessary to analyze performance of lightning striking to catenary of subway in viaduct section and propose an improving lightning protection scheme. In this paper, using ATP-EMTP simulation software to establish an associated model to evaluate lightning withstand level of catenary with existing lightning protection schemes including arrester and grounding point, an improving lightning protection scheme is proposed - every pillar ground earth and arresters are installed with some installing spacing between 200m to 400m based on lightning damage degree and reliability requirements - according to analyzing results: while lightning withstand level is lowest for lightning striking to the neutral pillar, lightning withstand level is greatest for lightning striking to the both-ends pillar that arrester and grounding point are both installed; grounding point could obviously improve lightning withstand level for lightning striking to ground wire while arrester could obviously improve the lightning withstand level for lightning striking to catenary; every pillar ground earth could enhance the lowest lightning withstanding level up to 2.5 times than of that pillar ground earth across every 200m.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2008.10a
• /
• pp.359-363
• /
• 2008

In recent warfare, importance of counter-fire is increased. New weapon system and counter-fire have critical impact on defeating of the enemy. At an initial battle counter-fire, we need to study about striking plan against the enemy mine artillery. In this paper, we studied, using MANA(agent based model), how much cannon's hit probability and UAV-based target acquisition have influence on striking the mine artillery. We constructed MANA model based on the characteristics of a regional database of Korean peninsula. If we develop detail database of the ROK Army, the proposed MANA model can be used as a war-game model for the regimental level of the Army.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.12
• /
• pp.1022-1032
• /
• 1989

King Sejong's Striking Clepsydra was an elaborate timekeeping and annunciating system incorporating biological automata capable of annunciating hours, intervals and night-watches based on Shou-shih calindrical systems automatically. In this paper the author has studied the original manuscripts on the Striking Clepsydra [Sejong sillock, 65: 1a-3b ff` 16th year, 7th month(1434)] from the technical point of view undertaking a close analysis of this monumental clock and aiming to our modern understanding of the full degree of delicate mechanisms and sophisticated controls built into the night-watch and division announcing clockwork(jackwork). Based on the input/output model, timekeeping, ball-rack, ball-relay, and audible time-indicating mechanisms were synthesized reconstructing night-watch annunciating systems. It revealed that the night-watch and division announcing processes were entirely renewed automatically. Historical and philological data concerning the improvements of the proposed model were discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.787-792
• /
• 1996

The method of manipulation by striking a part and letting it slide until it comes to rest, has been very little studied. However, the manipulation method is not uncommon in our daily lives. We analyze the dynamic behavior of a rigid polygonal part being striked and sliding on a horizontal surface under the action of fiction. There are two parts in this problem; one is the impact problem, and the other is the sliding problem. We characterize the impact and sliding dynamics with friction for polygonal parts, and present the possibility of reverse calculation for motion planning of striking operations. Using a high speed video camera, the computer simulation results are experimentally verified.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.702-706
• /
• 1996

The King Sejong's Striking water-clock was named for its distictive day and night time announcing system. Its time announcing system generates acoustic and visual signals for the twelve double hour, and combinations of two different acoustic signals for the five night watches, The mechanism of this signal generation system is triggered by a copper ball which is mechanically digitized time keeping signal, and is generated from the water clock. The time announcing system consisted four parts: 1) the mechanical amplifier which changes small copper to heavy steel ball, 2) day time announcing system, 3) night time announcing system, 4) sounding mechanism. The time announcing system of King Seong's Striking Clepsidra is remotely related to the Arabic clock system, however, it does have world-widely distictive mechanisms of its era, such as mechanical amplifier, self-weight rachet mechanism, and resetable mechanical computer etc.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1161-1168
• /
• 2002

Vibration and sound characteristics of King Song-Dok Bell are measured and the modal property is investigated. The effect of striking position and modal property on the beat characteristics is examined. It is first found that the beat characteristics are quite different according to the position on the bell surface and clear beat is periodically generated on the circumference. It turns out that in King Song-Dok Bell, striking Dangjwa(the present striking position) makes a beat in the first vibration mode, as well as it produces very clear beat in the second vibration mode.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.1
• /
• pp.1-14
• /
• 1997

This paper describes a series of numerical simulations of colision between a 310, 000 DWT double hull VLCC (struck ship) and three 35, 000, 70, 000 and 105, 000 DWT tankers (striking ships) using LS/DYNA3D. Collisions are assumed to occur at the middle of the VLCC with the striking ships moving at right angle to the VLCC centerline. Striking ship speeds are varied to find a critical speed without failure of inner side shell, and the informations of collision force and absorption energy of each case are also reported. The validation of LS/DYNA3D in this study was made by comparing the result of numerical simulation of LS/DYNA3D with that of double hull tanker grounding experiment by the Carderock Division of Navla Surface Warfare Center (CDNSWC).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.708-712
• /
• 2013

The appearance of the Korean bell is exceptional comparing to that of other bells. The sound of the Korean bell is also distinguishable because of its remarkable appearance. The sound of the Korean bell is composed of striking sound and residue sound. This study focuses mainly on the striking sound of the Korean bell. The primary purpose of this study is to suggest a proper sound quality evaluation method for Korean bell. To implement this study, examine the formerly established methods which are method using rating method and method using generally used Psychoacoustics metrics. Also, subjective Sound Quality evaluation was conducted to compare the results of method using rating method and the method using psychoacoustics metrics.