• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.296-306
• /
• 1998

Ongoing huge Bakun Hydropower project is including the construction of a 210 m height hydroelectric rockfill dam with an installed capacity of 2,520 MW and a power transmission system connecting to the existing networks between Sarawak and peninsula Malaysia. In order to allow the main dam construction during the dry season, the Ballui river will have to be detoured through 3 concrete lined diversion tunnels with an internal diameter of 12 m and a length of 1,400 m each. The geology of Bakun site belongs to the several thousand meters thick Belaga formation deposited from the late Cteteceous to the early Teriary in the Northwest Borneo geosyncline. The orientation of the bedding plane, strike at N55$^{\circ}$E to N70$^{\circ}$E and dip at 50$^{\circ}$SE to 70$^{\circ}$SE, is developed uniformly in Bakun sedimentary rocks. Rock mechanical characteristics of Bakun site have been classified into 4 rock mass types(RMT) depending on the degree of weathering and the occurrence of rock jointing with RMR. Graywacke(Sandstone) as well as Shale can take place together in the same rock mass type if their rock mass properties are similar. It was summarized the rock support type and support system design of underground diversion tunnels in view of rock mechanics.

• Economic and Environmental Geology
• /
• v.21 no.3
• /
• pp.235-255
• /
• 1988

Talc deposit of pipe-like form occurrs in the lower part of the Hyangsanri Dolomite with a strike of N40 -50 E and a dip of 40 -50 NW which is one formation of the Ogcheon Super Croup. The pipi-like ore body plunge at about $40^{\circ}$ to the west and are parallel to the lineation developed in the area. Structural formulae of tales occurred in this deposit are close to the ieal composition $Mg_6Si_8O_{20}(OH)_4$ showing limited deviation from ideal one. Substitution of Al for Si in tetrahedral site is of little or nothing ranging 0-0.04 and octahedral occupancy is close to six ranging 5.88-5.98 atoms per unit cell. Predominant octahedaral cation is Mg and proportion of divalent cations is generally over 97percent. Calcite -dolomite thermometry is obtained by determining the mol % $MgCO_3$using of EPMA and XRD methods. The peak metamorphic temperature can be estimated at $470{\pm}30^{\circ}C$ in the area whereas carbonates occurred at near talc ore show lower temperature than $400^{\circ}C$ that the calcite solvus limit is not well established. It indicates that the talc deposit was formed at the lower temperature that the metamorphic temperature. Cosequently, the formation of talc by metamorphism is questionable and the alteratin zone developed around the talc ore is very limited. The occurrence of talc ore in the dolomite as well as mineralogy, calcite-dolomite geothermometry, chlorite geothermometry, field and microscopic evidence suggest that siliceous ascending hydrothermal solution along the fracture is responsible for the formation of talc. It was considered that the slight fracturing of dolomite was formed by deformation prior to the mineralization.

• Economic and Environmental Geology
• /
• v.57 no.4
• /
• pp.363-370
• /
• 2024

To analyze the tectonic movements of the Geumwang Fault and its association with development of the Pungam Basin, the distributions of the gravity field and aeromagnetic field were interpreted. The low gravity zone (LGZ) around the Geumwang Fault shows an asymmetrical distribution, indicating sinistral (left-lateral) movement with the left side of the fault moving southeastward. The observed gravity anomaly suggests a displacement of approximately 9.3 km. The aeromagnetic distribution supports this horizontal displacement with very distinct magnetic characteristics. Using Euler deconvolution, the average depth of the Geumwang Fault was calculated to be about 1,000 meters, and it is estimated that the southwest side of the Pungam Basin is approximately 700 meters deeper than the northeast side. This strongly suggests that the Geumwang Fault has moved not only in a strike-slip but also in a dip direction. Such fault movement is characteristic of a hinge fault and has contributed to the formation of the basin through fault margin sag.

• Geophysics and Geophysical Exploration
• /
• v.13 no.1
• /
• pp.40-50
• /
• 2010

The building process of any geological map involves linking sparse lithological outcrop information with equally sparse geometrical measurements, all in a single entity which is the preferred interpretation of the field geologist. The actual veracity of this interpretative map is partially dependent upon the frequency and distribution of geological outcrops compounded by the complexity of the local geology. Geophysics is commonly used as a tool to augment the distribution of data points, however it normally does not have sufficient geometrical constraints due to: a) all geophysical inversion models being inherently non-unique; and b) the lack of knowledge of the physical property contrasts associated with specific lithologies. This contribution proposes the combined use of geophysical edge detection routines and 'three point' solutions from topographic data as a possible approach to obtaining geological contact geometry information (strike and dip), which can be used in the construction of a preliminary geological model. This derived geological information should first be assessed for its compatibility with the scale of the problem, and any directly observed geological data. Once verified it can be used to help constrain the preferred geological map interpretation being developed by the field geologist. The method models the contacts as planar surfaces. Therefore, it must be ensured that this assumption fits the scale and geometry of the problem. Two examples are shown from folded sequences at the Bathurst Mining Camp, New Brunswick, Canada.

• The Journal of Engineering Geology
• /
• v.22 no.1
• /
• pp.59-65
• /
• 2012

The purpose of this study is to analyze the direction of slope sliding that occurred at the highland ${\bigcirc}{\bigcirc}$ district in the Samcheok coalfield, using geological and structural detail surveys. The study area is dominated by the Paleozoic Pyong-an Group, and sliding is concentrated in zones of alternating sandstone and shale beds in the Geumcheon and Jangsung Formations. Discontinuities in the area have a strike of NE-SW and dip at 30~$80^{\circ}$ to the NW and 40~$80^{\circ}$ to the SE. However, some have strikes of NW-SE. In slide area group 1 (P1 to P4), en echelon tension gashes were caused by shearing. The surface in the areas of group 2 (P5 to P7) and group 3 (P8 and P9) is marked by step-type tension cracks that formed due to extension. This phenomenon caused anticlockwise rotation of the sliding slope. Otherwise, the cutting of the road side through the eastern slope of the mountain contributed to surface sliding due to geographical equilibrium loss.

• The Journal of Engineering Geology
• /
• v.24 no.3
• /
• pp.397-409
• /
• 2014

The appearance of faults during tunnel construction is often difficult to predict in terms of strike, dip, scale, and strength, even though this information is essential in determining the strength of the surrounding rock mass. However, the strength and rock mass classification of fault zones are generally determined empirically on the construction site. In this study, 109 specimens were collected from fault of nine area throughout Korea, and direct shear tests were conducted and the particle distribution was analyzed to better characterize the fault zones. Six multiple regression models were established, using 97 of the specimens, to analyze the correlation between the shear strengths and weight rations of these fault materials. A verification of the six models, using the remaining 12 specimens, shows that in all of the models the coefficient of determination yielded $R^2{\geq}0.60$, with two models yielding $R^2{\geq}0.69$. These results provide useful information for determining the shear strength of fault materials in future studies.

• Economic and Environmental Geology
• /
• v.13 no.3
• /
• pp.185-192
• /
• 1980

The rocks exposed in the investigation area are andesite of Late Cretaceous age, and syenite and aplitic granite of Bulgugsa Series of Early Cretaceous Period, which is intruded in the older andesitic rock. The strike and dip of major joint is $N10^{\circ}$ to $60^{\circ}E$, and $70^{\circ}SE$ to vertical respectively. According to seismic exploration, lower velocity zone, deemed to be fractured and/or crushed zone, is appeared along the gully center of east flank of the area. Test drilling shows that andesite bedrock is mostly very hard, massive, and very fine to medium grained and has almost 100 percent RQD and core recovery. In comparision with andesitic bedrock, intruded syenite cores show that it is highly crush especially at the depth from 55m to 63m.

• Journal of Conservation Science
• /
• v.16 s.16
• /
• pp.39-51
• /
• 2004

The standing Buddha named Taehwa 4 yew in the Jincheon were sculptured with rock cliff of the dark grey shale. Front of the Buddha statue shows $N40^{\circ}W$ strike with nearly vertical dip toward the back side. Rock blocks of the Buddha statue well developed with bedding and laminations whereas rock surface distributed into the various irregular discontinuities. Sculptured lines of the Buddha were uncertain because of degradation and exfoliations on the rock surface. The surface near the Buddha statue is highly contaminated with lichen and mosses, and accelerate physical and biological weathering owing to the roots of weed and bush along the fracture systems. For the conservational treatment, we treated with primary wet cleaning by air gun and secondary cleaning treatment using distilled water. Separated rock surface and fractured parts fasten and/or fill up the boundaries of the rock blocks using epoxy resin for conservation of rock properties. Some brittle surface was treatment with water repellent consolidant of ethyl silicates, and heterogeneous surface carried out color matching by acrylic pigments. Upper part of the Buddha statue dig out small ditch for rain water drainage, and near surface of the Buddha statue treat removal works for lichen, weeds and bush. The duration capacity of the Buddha constituting rocks are degraded by various weathering factors, therefore we suggest that this Buddha statue have need to do long term monitoring and synthetic conservation researches.

• The Journal of the Petrological Society of Korea
• /
• v.3 no.2
• /
• pp.138-155
• /
• 1994

Granitic gneiss containing biotite banded gneiss relict around the Daeheung talc deposit are widely distributed which were formed by regional metamorphism of both epidote-amphibolite and iater greenschist facies and granitization. They were derived from same silico-aluminous rocks of sedimentary origin. The mineral assemblages, which are common in the biotite banded gneiss, formed during regional metamorphisms, are survived in the granitic gneiss. The mineral assemblages of the latter greenschist facies may be formed retrogressively from the first epidote-amphibolite facies. The chemical compositions of biotite, muscovite, and chlorite, the important constituents of the gneisses, were controlled by the bulk composition, the chemical composition of the original mineral, and environment of the regional metamorphisms and granitization. The chemical equilibrium between coexisting'minerals, especially biotite and muscovite, is relatively well established, which was controlled mainly by tschermakitic and phengitic substitutions. Cholrite was formed mainly from either biotite or muscovite by retrogressive alteration or granitization, and have nearly similar chemical compositions regardless of the occurrences. The orientation trend of the foliation, joint and quartz vein developed in the gneisses was analyzed by equal area projection which the latter two show nearly identical trend in the strike and dip. This may suggest that the hydrothermal solution was introduced along joint during wet granitization.

• Economic and Environmental Geology
• /
• v.24 no.4
• /
• pp.421-434
• /
• 1991

Ground magnetic surveys were conducted at four areas where the Yangsan fault, the most prominent lineament in the Kyeongsang basin, appears to be passed through. For data processing, IGRF correction, upward continuation and reduction-to-the-pole were performed. The automatic inversion by using a matrix computation method, which takes the depth to bottom layer of the horizontal two layer structure as the model parameter, has been attempted to delineate the subsurface structure. Upward continuation of the surface magnetic map to the same level of the aeromagnetic survey (KIER, 1989) resulted in very similiar patterns to those of aeromagnetic data. Subsurface modeling of eight profile data show that the strike and dip of the Yangsan fault in study areas are $N6^{\circ}-15^{\circ}E$, and near vertical to somewhat eastward, repectively, despite of the local lithological contrast of each study area. It seems that the magnetic effect of faulting in the study area 1, which locates in the most northern part of the survey areas, is disturbed by that of igneous intrusion. At study area 2, the possibility of volcanic or igneous intrusion, which is 200-300 meters wide along the fault plane was presented. At study area 3, unlike other study areas, distinct fracture zone of 500-700 meters in width was revealed along the surface fault line. The andesitic rocks of the study area 4 have very high susceptibilities and the fault line on surface of this area was shifted about 500 meter eastward, as compared with the inferred fault line by the previous study.