• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.139-154
• /
• 1998

Under certain circumstance, premixed turbulent flame can be treated as wrinkled thin laminar flame and its motion in a hydrodynamic flow field has been investigated by employing G-equation. Past studies on G-equation successfully described certain aspects of laminar flame propagation such as effects of stretch on flame speed. In those studies, flames were regarded as a passive interface that does not influence the flow field. The experimental evidences, however, indicate that flow field can be significantly modified by the propagation of flames through the volume expansion of burned gas. In the present study, a new method to be used with G -equation is described to include the effect of volume expansion in the flame dynamics. The effect of volume expansion on the flow field is approximated by Biot-Savart law. The newly developed model is validated by comparison with existing analytical solutions of G -equation to predict flames propagating in hydrodynamic flow field without volume expansion. To further investigate the influence of volume expansion, present method was applied to initially wrinkled or planar flame propagating in an imposed velocity field and the average flame speed was evaluated from the ratio of flame surface area and projected area of unburned stream channel. It was observed that the initial wrinkling of flame cannot sustain itself without velocity disturbance and wrinkled structure decays into planar flame as the flame propagates. The rate of decay of the structure increased with volume expansion. The asymptotic change in the average burning speed occurs only with disturbed velocity field. Because volume expansion acts directly on the velocity field, the average burning speed is affected at all time when its effect is included. With relatively small temperature ratio of 3, the average flame speed increased 10%. The combined effect of volume expansion and flame stretch is also considered and the result implied that the effect of stretch is independent of volume release.

• The korean journal of orthodontics
• /
• v.27 no.6 s.65
• /
• pp.943-954
• /
• 1997

Forces needed for orthodontic tooth movement are obtained from various appliances such as orthodontic wires or elastic rubber. Orthodontic elastic rubber is widely used clinically, but permanent deformation and force decay may occur from the environmental changes, time of clinical use and the extent of the stretch, making the Prediction of force being applied difficult. The Present study examined and compared the changes in residual force between three brands of elastomeric chains (Ormco Generation II Power Chains ; brand A, RMO : Energy-Chain ; brand B, Unitek : AlastiK ; brand C) under various environmental conditions, amount of initial force, types of elastomer and the rate of extension. The characteristic physical properies of the elastomeric chains were as follows. 1. In all three brands, the residual force ratio was largest when the chains were stored in air, with no difference between water and saliva. 2. In all three brands, after 24 hours, there was no statistical difference in residual force ratio according to the initial force level. 3. In Brand A and B, the presence of filament had no correlation with the residual force ratio. In Brand C force decay was more severe when the chain contained filament. 4. In each brand, rate of extension had no effect on residual force ratio. 5. Brand B showed relatively higher residual force ratio compared to other brands.

• Korean Journal of Materials Research
• /
• v.22 no.1
• /
• pp.16-23
• /
• 2012

Research into the development of high strength (1 GPa) and superior formability, such as total elongation (10%), and stretch-flangeability (50%) in hot-rolled steel was conducted with a thermomechanically controlled hot-rolling process. To improve the overall mechanical properties simultaneously, low-carbon steel using precipitation hardening of Ti-Nb-V multimicroalloying elements was employed. And, ideal microstructural characteristics for the realization of balanced mechanical properties were determined using SEM, EBSD, and TEM analyses. The developed steel, 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V), consisted of ferrite as the matrix phase and second phase of granular bainite with fine carbides (20-50 nm) in both phases. The significant factor of the microstructural characteristics that affect stretch-flangeability was found to be the microstructural homogeneity. The microstructural homogeneity, manifest in such characteristics as low localization of plastic strain and internally stored energy, was identified by grain average misorientation method, analyzed by electron backscattered diffraction (EBSD) and hardness deviation between the phases. In summar, a hot-rolled steel having a composition 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V) demonstrated a tensile strength of 998 MPa, a total elongation of 19%, and a hole expansion ratio of 65%. The most important factors to satisfy the mechanical property were the presence of fine carbides and the microstructural homogeneity, which provided low hardness deviation between the phases.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.128-132
• /
• 2017

Harmonic structure materials are materials with a core-shell structure having a shell with a small grain size and a core with a relatively large grain size. They are in the spotlight because their mechanical properties reportedly feature strength similar to that of a sintered powder with a fine grain size and elongation similar to that of a sintered powder with a coarse grain size at the same time. In this study, the tensile properties, microstructure, and stretch-flangeability of harmonic structure SUS304L made using powder metallurgy are investigated to check its suitability for automotive applications. The harmonic powders are made by mechanical milling and sintered using a spark plasma sintering method at 1173 K and a pressure of 50 MPa in a cylindrical die. The sintered powders of SUS304L having harmonic structure (harmonic SUS304L) exhibit excellent tensile properties compared with sintered powders of SUS304L having homogeneous microstructure. In addition, the harmonic SUS304L has excellent stretch-flangeability compared with commercial advanced high-strength steels (AHSSs) at a similar strength grade. Thus, the harmonic SUS304L is more suitable for automotive applications than conventional AHSSs because it exhibits both excellent tensile properties and stretch-flangeability.

• Korean Journal of Metals and Materials
• /
• v.50 no.7
• /
• pp.487-493
• /
• 2012

To analyze the factors on stretch-flangeability for 980 MPa-grade hot-rolled steels, two types of steels (Fe-Cr and Fe-Mo) were manufactured by hot-rolling. Manufactured steels at the low coiling temperature, such as 400 and $500^{\circ}C$, had poor stretch-flangeability due to un-uniformly distributed carbides and a large deviation of interphase hardness. However, when the coiling temperature was set at $650^{\circ}C$ with Fe-Cr steel, 998 MPa of ultimate tensile strength, 19% of total elongation and 65% of the hole expanding ratio were achieved by microstructural constituents of polygonal ferrite (PF) and granular ferrite (GF) dispersed with fine carbides (<50 nm). Therefore, the material to attain 980 MPa with superior formability was the Fe-Cr steel that was precipitation-hardened in polygonal ferrite and granular ferrite at the coiling temperature $650^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.75-81
• /
• 2006

Lean premixed combustion is a well known method for low $NO_x$ gas turbine combustor. But lean combustion is usually accompanied by flame instability. To overcome this problem, the hydrogen ($H_2$) was added to main fuel methane to increase flammable limit. In this paper, the effects of hydrogen addition on lean premixed combustion of methane ($CH_4$) were investigated numerically. Results showed that the extinction stretch rate increases and the extinction temperature constant with relatively small amount of $H_2$ addition. The flame temperature and NO emission increase with $H_2$ addition at the same stretch rate and equivalence ratio but it could increase the range of lean extinction and extinction equivalence ratio limit. Eventually, the $H_2$ addition case showed almost same or lower NO emission than no addictive $CH_4$ case in the extinction condition.

• Elastomers and Composites
• /
• v.38 no.2
• /
• pp.157-166
• /
• 2003

The Edwards-Vilgis slip-link theory and the Kaliske-Heinrich extended tube theory were tested experimentally using published experimental data on networks of natural and isoprene rubber and on polysiloxane networks. All parameters were adjusted to achieve an optimum fit. The data description obtained with the EV theory is not satisfactory and the parameter values tend to lie outside their reasonably expected range. But for the region of low strains, the Kaliske-Heinrich theory offers a satisfactorily accurate data description which is able to serve for practical purposes. Its crosslink term, however, is based on approximations which lead to a questionable prediction and values determined for the exponent in the entanglement term lie outside the range expected by the KH model. Thus, the title question cannot be given a positive answer. Conclusions published earlier that the trapped entanglements contribute both to the crosslink and constraint (entanglement) term are supported by the present data analysis. Experimental equibiaxial data on hydrocarbon networks do not show any maximum on their stretch ratio dependence, contrary to the predictions of molecular theories. The stretch ratio dependences of relative reduced stresses do not sensitively reflect differences in the chemical nature of the chain backbone (hydrocarbon vs. siloxane) and in the crosslinking method (end-linking vs. random crosslinking).

• Smart Structures and Systems
• /
• v.25 no.3
• /
• pp.311-322
• /
• 2020

This paper studies the influence of parameters of a novel SMA helical spring energy dissipation brace on the seismic resistance of a frame structure. The force-displacement relationship of the SMA springs is established mathematically based on a multilinear constitutive model of the SMA material. Four SMA helical springs are fabricated, and the force-displacement relationship curves of the SMA springs are obtained via tension tests. A numerical dynamic model of a two-floor frame with spring energy dissipation braces is constructed and evaluated via vibration table tests. Then, two spring parameters, namely, the ratio of the helical spring diameter to the wire diameter and the pre-stretch length, are selected to investigate their influences on the seismic responses of the frame structure. The simulation results demonstrate that the optimal ratio of the helical spring diameter to the wire diameter can be found to minimize the absolute acceleration and the relative displacement of the frame structure. Meanwhile, if the pre-stretch length is assigned a suitable value, excellent vibration reduction performance can be realized. Compared with the frame structure without braces, the frames with spring braces exhibit highly satisfactory seismic resistance performance under various earthquake waves. However, it is necessary to select an SMA spring with optimal parameters for realizing optimal vibration reduction performance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.154-157
• /
• 2001

Through this study we investigated the causes of bottom crack. We then redesigned petaloid bottom to prevent bottom crack. We examined the material property variations according to the stretch ratio of PET and analyzed stretches of bottom in blowing processes. We also performed crack test to observe a crack phenomena. The effective stress and maximum principal stress were examined by computer simulation. We concluded that the bottom crack occurs because of not only insufficient strength of material due to the insufficient stretch of PET but also coarse design of petaloid shape. The highest maximum principal stress occurred at valley in petaloid bottom of bottle and this strongly affected the crack in bottom. We redesigned petaloid shape to minimize maximum principal stress, and this result in increasing the crack resistance.

• Textile Coloration and Finishing
• /
• v.13 no.1
• /
• pp.68-75
• /
• 2001

Tensile and shrinkage characteristics of DTY, EDY and Macel were investigated experimentally. The drawn textured yarn(DTY) made by an existing belt type false twist and the elastic drawn textured yarn(EDY) made by non-torque false twist method modified from the belt type one. Macel was the yarn which had drawn and un-drawn arrangements. The tenacity of EDY had lower value than that of DTY. EDY had higher strethch than that of DTY. Especially Macel yarn had higher stretch than that of DTY compared with the same diameter of yarn. With time course behavior the tenacity and elongation of DTY and EDY had stabled tendency without variation. Before scouring Process, the wet and dry shrinkage patio of EDY load higher value than that of DTY. However, they decreased artier the process. At the same time, the stretch characteristic of EDY was significant as the diameter of yarn became higher.