• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1130-1135
• /
• 2004

The vertical roller mill is the important machine grinding and mixing various crude materials in the manufacturing process of portland cement. Vertical roller mill is subjected to the cyclic bending stress by rollers load. It demands $4{\times}10^7$ cycle but has $4{\times}10^6{\sim}8{\times}10^6$ cycle. It fractures at the edge of grinding path of outside roller. The repair expense for it amounts to 30% of total maintenance. Therefore, this study shows optimal design for vertical roller mill using DOE and neural network.

• Structural Engineering and Mechanics
• /
• v.5 no.6
• /
• pp.743-754
• /
• 1997

A three-dimensional constitutive modeling for reinforced concrete is presented for finite element nonlinear analysis of reinforced concrete. The targets of interest to the authors are columns confined by lateral steel hoops, RC thin shells subjected to combined in-plane and out-of-plane actions and massive structures of three-dimensional (3D) extent in shear. The elasto-plastic and continuum fracture law is applied to pre-cracked solid concrete. For post cracking formulation, fixed multi-directional smeared crack model is adopted for RC domains of 3D geometry subjected to monotonic and reversed cyclic actions. The authors propose a new scheme of decomposing stress strain fields into sub-planes on which 2D constitutive laws can be applied. The proposed model for 3D reinforced concrete is experimentally verified in both member and structural levels under cyclic actions.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1309-1314
• /
• 2014

The measurement of stator core loss for an induction motor at each manufacturing process is carried out in this paper. Iron loss in the stator core of induction motor changes after each manufacturing process due to the mechanical stress, which can cause the deterioration of the magnetic performances. This paper proposes a new iron loss measuring system of the stator core in an induction motor, which can be applied to the case when the distribution of magnetic flux density is not uniform along the magnetic flux path. In the system, the iron loss is calculated based on the induced voltage of the B-search coil and exciting current.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.1
• /
• pp.52-56
• /
• 2006

This paper presents a cross-eye characteristics of multi-path wave scattering. Cross-eye method uses the phase differences of multi signals and is used fur electronic protection. When a signal is propagated from transmitter to receiver on the ground surface, direct wave and reflected wave signals are combined in front of the receiving antenna with different phases. To calculate and control the amplitude and phase of reflected signal, we have developed a cross eye electronic protection method for radar system and studied the variation of electric power density.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.3
• /
• pp.257-260
• /
• 2010

Advancements in the imaging and computing technology have opened the path to digital holography for non-destructive investigations of technical samples, material property measurement, vibration analysis, flow visualization and stress analysis in aerospace industry which has widened the application of digital holography in the above fields. In this paper, we demonstrate the non-destructive investigation and micro-structure measurement application of digital holography to the small particles and a biological sample. This paper gives a brief description of the digital holograms recorded with this system and illustratively demonstrated.

• Computers and Concrete
• /
• v.8 no.4
• /
• pp.473-489
• /
• 2011

In designing a flexural member for structural safety, both the flexural strength and ductility have to be considered. For this purpose, the flexural ductility of reinforced concrete sections has been studied quite extensively. As there have been relatively few studies on the flexural ductility of prestressed concrete sections, it is not well understood how various structural parameters affect the flexural ductility. In the present study, the full-range flexural responses of reinforced and prestressed concrete sections are analyzed taking into account the nonlinearity and stress-path dependence of constitutive materials. From the numerical results, the effects of steel content, yield strength and degree of prestressing on the yield curvature and ultimate curvature are evaluated. It is found that whilst the concept of flexural ductility in terms of the ductility factor works well for reinforced sections, it can be misleading when applied to prestressed concrete sections. For prestressed concrete sections, the concept of flexural deformability in terms of ultimate curvature times overall depth of section may be more appropriate.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.17 no.2
• /
• pp.65-74
• /
• 2021

This study aims to assess the effect of postulated seismic loads on the structural integrity of a spent nuclear fuel dry storage facility. Firstly, three-dimensional modal and response spectrum analyses were carried out. With regard to the latter analysis, the effect of incident angles against two horizontal and one vertical response spectra was also considered. Results showed that even though two critical locations were predicted at the longitudinal axis central part of upper flow path as well as the end discontinuity part of upper and lower flow paths connector, their maximum principal stress values were less than the tensile strength. Moreover, since the influence of vertical angle was 87% higher than that of horizontal angle in particular, which should be carefully handled to demonstrate integrity of the facility.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.6
• /
• pp.135-141
• /
• 1997

Low velocity impact test and compressive residual strength test after impact were performed by using Hercules AS4/3501-6[45/0/-45/90]$_{2s}$ laminated plate to investigate the low velocity impact damage behavior and the post-impact strength degradation on orthotropic composite laminate plate. Due to the lateral impact losd, the load path showed "" shape according to the laminate central deflection. Damage in a laminate occurs by inclined matrix crack at the damage initiation load stage and vertical matrix crack, occurs on the outer surface. Evaluating the compressive residual strength after the low velocty impact test, it could be found that there is a transient range where the compressive residual strength drop suddenly in the initial damage which is in the matrix crack range and the initial delamination area. is in the matrix crack range and the initial delamination area.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.19 no.2
• /
• pp.171-178
• /
• 2023

For the phase boundary crack found in the gasket made of cast austenitic stainless steel in the nuclear power plant, the oxide layers were analyzed through SEM and TEM. The results showed that cracks initiated and propagated along the austenite/δ-ferrite phase boundary, the propagation path was changed to penetrate the inside of the phase. The oxide layer located at the periphery of the crack along the phase boundary was identified as a complex multi-layered spinel structure, and Cr-rich carbides were also detected in the oxide. The cracks that propagated inside the austenite matrix were attributed to the presence of high external stresses and impurities.

• Journal of Digital Convergence
• /
• v.12 no.7
• /
• pp.337-348
• /
• 2014

The purpose of this study was to analyze major factors of turnover intention among job stress, job satisfaction and organizational commitment in hospitals. The data were collected from 2 university hospitals and 2 general hospitals workers in Busan and Gyeongnam area from July. 3 to July. 19, 2013. The main results were summarized as follows. Job stress was a direct impact on job satisfaction, organizational commitment and an indirect impact via job satisfaction. It was a direct impact on employees turnover intention and an indirect impact via job satisfaction, organizational commitment. Job satisfaction was a direct impact on organizational commitment and an indirect impact on employees turnover intention via organizational commitment. Organizational commitment was a direct impact on employees turnover intention. Finally, in order to decrease turnover intention, controling job stress is important. Hospital staffs should develope programs for hospital employees to reduce job stress and enhance their ability.