• Journal of Photoscience
• /
• v.3 no.1
• /
• pp.15-21
• /
• 1996

To investigate the chilling sensitivity related injuries in the photosynthetic apparatus of cucumber leaves, the light-chilling induced alterations of chlorophyll fluorescence transients in cucumber leaves were compared with those in pea leaves. As an early effect of light-chilling, an increase in Fp/Fm$^*$ was observed in both pea and cucumber leaves, which was saturated by about 6 h chilling. However, the saturated value of Fp/Fm was almost 1.0 in cucumber, in contrast to about 0.8 in pea. During the recovery period after 24 h chilling, the light-chilling induced changes in pea seemed to be reversed, but those in cucumber leaves were thought to be irreversible, because Fo was increased significantly. Light-chilling caused significant decreases in qQ and qE in cucumber leaves, but qR was increased until 6 h, and decreased thereafter. In both pea and cucumber leaves, Fm was increased by 2 h dark treatment. The Fm from the predarkened pea leaf discs was higher than the value from the preilluminated ones during the whole period of light-chilling (500 $\mu$mol m$^{-2}$s$^{-1}$ PAR). However, the predarkened cucumber leaf discs showed a reduction in Fm and an increase in Fo during the 2 h chilling in the light. These results indicate that the causes of chilling sensitivities in photosynthetic apparatus of cucumber leaves are possibly related with the damage in PSI reaction center and the ability of acidification of lumen by PSII.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.186-195
• /
• 2000

In this paper, partial discharge (PD) measurement was performed to evaluate the quality of the cable joint and termination constructions. The resistive coupling technique for PD detection using resistivity of semiconducting layer of the cable in the accessories, such as joints and terminations. With high frequency PD (HEPD) measurement, an excellent sensitivity below 20pC could be achieved under unshielded condition. The localization of the defects in the accessories could be identified. During heating cycle, PDs were monitored and analyzed. At that time, the PDs were dependent on the temperature of the heating cycle and showed cyclic behaviors, which were attributed to local delamination of the interfaces, between epoxy unit and stress relief cone(SRC) and between SRC and cable, due to the difference of thermal expansion. As a conclusion, HFPD measurement technique was proven to be an effective diagnostic method for qualification of extra high voltage (EHV) cable accessories. With this technique, the optimal design of the components of the accessories could be verified not only in an early stage but also under operating condition. This technique would result in the improvement of the reliability of the EHV cable accessories.

• Structural Engineering and Mechanics
• /
• v.47 no.4
• /
• pp.559-573
• /
• 2013

Geometrically non-linear axisymmetric bending of a shallow spherical shell with a clamped or a simply supported edge under axisymmetric load was investigated numerically. The partial load was introduced by the Heaviside step function, and the solution was obtained by the finite difference and the Newton-Raphson methods. The thickness of the shell was considered to be uniform and the material was assumed to be homogeneous and isotropic. Sensitivity analysis was made for three geometrical parameters. The accuracy of the algorithm was checked by comparing the central deflection, the radial membrane stress at the edge, or the transverse shear force with the solutions of plates and shells in the literature and good agreement was obtained. The main findings of the study can be outlined as follows: (i) If the shell is fully loaded the central deflection of a clamped shell is larger than that of a simply supported shell provided that the shell is not very shallow, (ii) if the shell is partially loaded the central deflection of the shell is sensitive to the parameters of thickness, depth, and partial loading but the influence of the boundary conditions is negligible.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.4
• /
• pp.9-14
• /
• 1985

In this research mass of a plane strain two dimensional elastic concrete dam under gravitational and hydrostatic loads is minimized, through shape optimization of the dam cross section. Cross sectional area of the dam is taken as cost function of the optimization problem while constraints on the principal stress distribution and dam thickness are imposed. Shape of the boundary of the model is chosen as design variable. Variational formulation of the optimization problem, the material derivative idea of continuum mechanics, and an adjoint variable method are employed for the shape design sensitivity calculation. Then the gradient projection algorithm is utilized to obtain an optimum design iteratively. Research results fully demonstrate that the theory and procedure adopted are quite efficient and can be applicable to a wide class of practical elastic structural design problems.

• Journal of the Korean Society of Safety
• /
• v.28 no.6
• /
• pp.11-16
• /
• 2013

This paper presents a study on the analyzing reliability of smoke fire detector using accelerated life test. In general, the smoke fire detector is broken by dust which flow in smoke detection chamber. In order to conduct accelerated life test of smoke fire detector dust is set accelerated factor in this paper. The dust is fly-ash which is test particle 5th regulated by KS A 0090. The dust accelerated level is 60 g, 180 g and 360 g and failure time is measured by smoke sensitivity testing. It is considered to failure of detector if detector don't operate within 30 secconds when subjected to an air stream having a velocity of 20 cm/s~40 cm/s containing smoke with a concentration of 15% of rate of light-response of 1 m. The goodness of fit test and mean life prediction conduct using the failure time. The result show that life distribution fits the weibull distribution for failure time data and the mean lifes calculate 22.5 year in domestic product and 14.7 years in overseas product applied dust stress only.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1369-1375
• /
• 2006

In this work, mechanical characteristics of stainless steel diaphragm have been studied as a potential robust substrate and a diaphragm material for micromachined devices. Lamination process techniques combined with traditional micromachining processes have been adopted as suitable fabrication technologies. To illustrate these principles, capacitive pressure sensors based on a stainless steel diaphragm have been designed, fabricated and characterized. The fabrication process for stainless steel micromachined devices keeps the membrane and substrate being at the environment of 8.65MPa pressure and $175^{\circ}C$ for a half hour and then subsequently cooled to $25^{\circ}C$. Each sensor uses a stainless steel substrate, a laminated stainless steel film as a suspended movable plate and a fixed, surface micromachined back electrode of electroplated nickel. The finite element method is adopted to investigate residual stresses formed in the process. Besides, out-of-plane deflections are calculated under pressures on the diaphragm. The sensitivity of the device fabricated using these technologies is 9.03 ppm $kPa^{-1}$ with a net capacitance change of 0.14 pF over a range 0$\sim$180 kPa.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.2 s.41
• /
• pp.7-15
• /
• 2007

A numerical procedure for optimizing the shape of three-dimensional channel with V-shaped ribs extruded on both walls has been carried out to enhance the turbulent heat transfer. The response surface based optimization is used as an optimization technique with Reynolds-averaged Wavier-stoked analysis. Shear stress transport (SST) turbulence model is used as a turbulence closure. Computational results for average heat transfer rate show good agreements with experimental data. The objective function is defined as a linear combination of heat transfer and friction loss-related terms with a weighting factor. Three dimensionless variables such as, rib pitch-to-rib height ratio, rib height-to-channel height ratio, and the attack angle of the rib are chosen as design variables. Nineteen training points obtained by D-optimal designs for three design variables construct a reliable response surface. In the sensitivity analysis, it is found that the objective function is most sensitive to the ratio of rib height-to-channel height ratio. And, optimal values of design variables have been obtained in a range of the weighting factor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.4
• /
• pp.127-135
• /
• 1984

This paper considers the problem of optimum shaping of steel arches subjected to general loading. The weight of arches is considered as the objective function and the appropriate combinations of section forces, material volume, arc length, and closed section area of arches are considered as the stress constraints. The shape optimization problems are formulated in terms of the design variables of sectional areas of each element. First the cost sensitivity of the design is investigated. Then the investigation comprises the search for the optimum arch form as well as the optimum area distribution along the arch. Two spaces of shape optimization algorithm will be treated, the first space corresponding to the section optimization by the Modified Newton Raphson Method, and the second space to the coordinate optimization by the Powell Method. The optimization algorithm is evaluated and the optimum span-rise ratios for the given arches are evaluated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.3
• /
• pp.505-513
• /
• 2002

During heatup and cooldown of pressurized water reactor, thermal stress was generated in the reactor pressure vessel (RPV) because of the temperature gradient. To prevent potential failure of RPV, pressure was required to be maintained below the P-T limit curves. In this paper, several methods for constructing the P-T limit curves including the ASME Sec. XI, App. G method were explained and the results were compared. Then, the effects of the various parameters such as flaw size, flaw orientation, cooldown rate, existence of chad, and reference fracture toughness, were evaluated. It was found that the current ASME Sec. XI App. G method resulted in the most conservative P-T limit curve. As the more accurate fracture mechanics analysis results were used, some of the conservatism can be removed. Among the parameters analysed, reference flaw orientation and reference fracture toughness curve had the greatest effect on the resulting P-T limit curves.

• Journal of Sensor Science and Technology
• /
• v.16 no.1
• /
• pp.62-67
• /
• 2007

This paper presents a novel MEMS condenser microphone with rigid backplate to enhance acoustic characteristics. The MEMS condenser microphone consists of membrane and backplate chips which are bonded together by gold-tin (Au/Sn) eutectic solder bonding. The membrane chip has 2.5 mm${\times}$2.5 mm, $0.5{\mu}m$ thick low stress silicon nitride membrane, 2 mm${\times}$2 mm Au/Ni/Cr membrane electrode, and $3{\mu}m$ thick Au/Sn layer. The backplate chip has 2 mm${\times}$2 mm, $150{\mu}m$ thick single crystal silicon rigid backplate, 1.8 mm${\times}$1.8 mm backplate electrode, and air gap, which is fabricated by bulk micromachining and silicon deep reactive ion etching. Slots and $50-60{\mu}m$ radius circular acoustic holes to reduce air damping are also formed in the backplate chip. The fabricated microphone sensitivity is $39.8{\mu}V/Pa$ (-88 dB re. 1 V/Pa) at 1 kHz and 28 V polarization voltage. The microphone shows flat frequency response within 1 dB between 20 Hz and 5 kHz.