• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.661-676
• /
• 2016

This paper presents an elastic/plastic model that neglects strain hardening during loading, but accounts for the Bauschinger effect. These mathematical features of the model represent reasonably well the actual behavior of several materials such as high strength steels. Previous attempts to describe the behavior of this kind of materials have been restricted to a class of boundary value problems in which the state of stress in the plastic region is completely controlled by the yield stress in tension or torsion. In particular, the yield stress is supposed to be constant during loading and the forward plastic strain reduces the yield stress to be used to describe reversed yielding. The new model generalizes this approach on plane stress problems assuming that the material obeys the von Mises yield criterion during loading. Then, the model is adopted to describe reversed yielding in thin hollow discs subject to external pressure.

• 대한조선학회논문집
• /
• 제43권2호
• /
• pp.213-219
• /
• 2006

Low cycle fatigue cracks are mainly detected at discontinuous welded locations with high stresses under repeated cyclic static loads due to cargo leading and unloading. Theoretical and analytical methods have been used for evaluation of local stress and strain which have an effect on a prediction of fatigue life, but those have difficulties of considering stress concentration at notched location and complicated material behavior of welded joint or heat affected zone. Electronic speckle pattern interferometry(ESPI) system is nondestructive and non-contact measurement system which can get the relatively accurate full field strain at critical positions such as welded zone and structural discontinuous location. In this study, local strain was measured on welded cruciform joint by ESPI system and then low cycle fatigue test was performed. Effect of local strain on low cycle fatigue life was examined by measured values using ESPI system. Moreover, experimental fatigue life was compared with established S-N curves using theoretical local strain and stress calculated by Neuber's rule.

• 소성∙가공
• /
• 제15권8호
• /
• pp.544-549
• /
• 2006

In this work, we have employed the strain gradient plasticity theory to investigate the effect of material size on the deformation behavior in metal forming process. Flow stress is expressed in terms of strain, strain gradient (spatial derivative of strain) and intrinsic material length. The least square method coupled with strain gradient plasticity was used to calculate the components of strain gradient at each element of material. For demonstrating the size effect, the proposed approach has been applied to plane compression process and micro rolling process. Results show when the characteristic length of the material comes to the intrinsic material length, the effect of strain gradient is noteworthy. For the microcompression, the additional work hardening at higher strain gradient regions results in uniform distribution of strain. In the case of micro-rolling, the strain gradient is remarkable at the exit section where the actual reduction of the rolling finishes and subsequently strong work hardening take places at the section. This results in a considerable increase in rolling force. Rolling force with the strain gradient plasticity considered in analysis increases by 20% compared to that with conventional plasticity theory.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1992년도 가을 학술발표회 논문집
• /
• pp.111-118
• /
• 1992

The mechanical behaviors related to the strain rate effect and the tensile strength of high-strength concrete were investigated in this study. For this purpose, concrete cylinder specimens with 4 different compressive strengths from 232kg/$\textrm{cm}^2$ to 1113kgf/$\textrm{cm}^2$ were tested and analysed on the mechanical properties(stress-strain relationship, compressive, modulus of elasticity, strain at peak compressive stress). From this experimental and analytical study, it seems that the current prediction model(ACI) for modulus of rupture need to be refined. Therefore, more refined equations for evaluation tensile strength of concrete are proposed.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.171-178
• /
• 1996

DCB(pure mode I) and CLS(mixed mode) tests were performed to investigate the effect of fracture mode on the interlaminar fracture of composite laminate. Mode I critical strain energy release rate was found to be $133J/m^2$ from the DCB test and total strain energy release rate decreased from $1, 270J/m^2$ as thickness ratio(tl/t) varied from 0.333 to 0.667 from the crease from the CLS test. Crack length had no effect on the total strain energy release rate and load was almost constant during the crack growth of the specimen which had the specific thickness ratio. Crack initiated when the stress of the strap ply reached constant stress $42kgf/mm^2$ which was found to be independent of the thickness ratio.

• 한국지반공학회논문집
• /
• 제17권6호
• /
• pp.135-148
• /
• 2001

본 연구에서는, 인장력과 이에 수직방향으로 작용하는 압축음력을 동시에 고려한 직교이방성 합성부재의 인장력-변형률 관계식(Bhagwan, Agarwal & Brouoan, 1990)을 응용하여, 토목섬유인발저항력 및 인장력에 미치는 구속응력의 영향을 정량적으로 평가할 수 있는 기법을 제시하였다. 이를 위해서, 국내에서 판매되고 있는 부직포, 직포, 복합포 및 지오그리드 등의 토목섬유를 대상으로 구속신장시험(Confined Extension Test) 및 실내인발시험(Laboratory Pull-out Test)을 수행하였다. 시험결과를 토대로하여 구속응력이 토목섬유의 인장력-변형률 거동에 미치는 영향을 분석하였고, 구속응력에 의한 토목섬유 인장력 및 인발저항력의 변화를 정량적으로 평가하였다. 분석결과, 구속응력의 크기가 증가할수록 토목섬유의 할선계수가 뚜렷이 증가하였으며, 본 연구 제안방법에 의한 토목섬유-흙 사이의 마찰저항각 $\delta\; 및\; 보정계수\; a^2$값이 기존의 인발저항력 평가방법에 비하여 다소 큰 값을 나타내어, 인발저항력 산정시 토목섬유에 가해지는 구속음력의 크기를 고려하는 본 연구 제시방법의 경우에 보다 큰 인발저항력이 얻어짐을 알 수 있었다.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.625-631
• /
• 2006

구조재의 잔류응력(residual stress)은 외부에서 하중이 작용하지 않는 상태에서도 구조물 내부에 존재하는 응력으로 건설현장에서 구조물을 설치, 조립하는 경우에 발생하게 되며 특히 용접이나 과부하에 의한 구조물의 설치 후에도 발생할 수 있다. 이에 본 연구에서는 600MPa급 mega structure용 강관제작 상의 프레스 및 용접에 의한 잔류응력의 영향을 파악하고자 홀드릴링 변형게이지법(Hole-Drilling Strain Gage Method)을 이용하여 용접선 부근을 중심으로 총 59개소를 측정하여 잔류응력의 분포 및 크기를 평가하였다.

• 한국생산제조학회지
• /
• 제8권2호
• /
• pp.27-34
• /
• 1999

The growth-strain method was used for shape optimization, which carries out the optimization by distributing uniformly the distributed parameter such as von Mises stress and shear strain energy density. Shape optimization is carried out by iteration of stress analysis and growth strain analysis. In this study, the effect of growth ratio in the method was investigated and then the range of the adequate value of the growth ratio was determined. Also the growth-strain method was improved by applying the linear PID control theory in order to control volume required by a designer. Finally, an automatic shape optimization system was built up by the improved growth-strain method with a commercial software using finite element method. The effectiveness and practicability of the developed shape optimization system was verified by some examples.

• 대한기계학회논문집A
• /
• 제32권6호
• /
• pp.488-495
• /
• 2008

In order to achieve long fatigue lifetimes for cyclically pressurized thick cylinders, multi-layered compound cylinder has been proposed. Such compound cylinder involves a shrink-fit procedure incorporating a monobloc tube which has previously undergone autofrettage. The basic autofrettage theory assumes elastic-perfectly plastic behaviour. Because of the Bauschinger effect and strain-hardening, most materials do not display elastic-perfectly plastic properties and consequently various autofrettage mo dels are based on different simplified material strain-hardening models, which is assumed that combination of linear strain-hardenig and power strain-hardening model. This approach gives a more accurate prediction than the elastic-perfectly plastic model and is suitable for different strain-hardening materials. In this paper, a general autofrettage model that incorporates the material strain-hardening relationship and the Bauschinger effect, based upon the actual tensile-compressive stress-strain curve of a material was proposed. The model was obtained using the von Mises yield criterion and plane strain condition. The tensile-compressive stress-strain curve was obtained by experiment. The parameters needed in the model were determined by fitting the actual tensile-compressive curve of the material. Finally, strain- hardening model was compared with elastic-perfectly plastic model.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1772-1782
• /
• 1993

The characteristics of metal matrix composite under dynamic tension at high strain rates up to the order of $10^3/sec$ is studied by using newly developed apparatus. The composite material processed in this research is aluminum-alumina metal matrix composites, arid fabricated by compocasting with the fiber volume fraction from 5 to 20%. The whisker and matrix material used in this paper were ${\delta}-Al_2O_3$ and Al-6061, respectively. The mechanical tests performed in this research are low and high strain rate tensile test. At low strain-rate tensile test, the modulus of elasticity and the ultimate tensile strength of the composites were improved about 77 pct. and 55 pct., respectively comparing with the unreinforced materials. At strain-rate from $10^{-3}\;to\;10^3/s$, the effect of strain-rate on the modulus, ultimate strength, flow stress is determined. Also the effect of strain rate on the modulus, ultimate tensile strength, flow stress and elongation to failures were investigated.