• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.405-410
• /
• 2002

This paper deals with the flexural behavior of RC hems strengthened with CFRP plate and the estimation on anchorage length of CFRP Plate. Experimental variables included concrete strength, reinforcement ratio, cover thickness of concrete and length ratio of CFRP plate for a pure span. A failure load, failure mode, deflection and strain response at different distances from a cut-off point of CFRP plate were observed and anchorage length was determined through strain distribution of CFRP plate. Herein, anchorage length is defined the length between CFRP plate end and the beginning point of full composite behavior. Also, the anchorage length observed from the experiment was compared with Nguyen's equation and BS specification.

• Proceedings of the KWS Conference
• /
• 2008.05a
• /
• pp.11-11
• /
• 2008

• Structural Engineering and Mechanics
• /
• v.18 no.5
• /
• pp.609-626
• /
• 2004

The Land Transport Authority of Singapore has a continuing program of highway bridge upgrading, to refurbish and strengthen bridges to allow for increasing vehicle traffic and increasing axle loads. One subject of this program has been a short span bridge taking a busy highway across a coastal inlet near a major port facility. Experiment-based structural assessments of the bridge were conducted before and after upgrading works including strengthening. Each assessment exercise comprised two separate components; a strain and acceleration monitoring exercise lasting approximately one month, and a full-scale dynamic test carried out in a single day. This paper reports the application of extreme value statistics to estimate bridge live loads using strain measurements.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.357-360
• /
• 2006

In this study, it was proposed a direct tensile testing machine(DTTM) to be simple and to be applied to High Performance Fiber Reinforced Cementitious Composites(HPFRCCs), and it was examined the tensile properties of HPFRCCs by this machine. As a results, it was confirmed that a direct tensile test of HPFRCCs could be certainly carried out DTTM to be developed in this study. Also, tensile strength and yield strength of HPFRCCs were similar regardless of specimens thickness. And, all specimens revealed the stable strain-hardening behavior and multiple cracking in flexible and tensile loads. But, deviation of strain at ultimate tensile strength increased with the increase of specimen thickness.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.539-544
• /
• 2009

The constraint effect $A_2$ has to be evaluated within plastic region near crack tip front using opening displacement. Plastic boundary and stress or strain conditions in the vicinity of the crack tip using recrystallization heat treatment was represented. It was found that the plastic deformation boundary by recrystallization heat treatment method was the true strain of ${\epsilon}t$ = 0.05mm/mm. With the estimation of constraint effects $A_2$, the region of proper displacement measurement point near crack tip was between 0mm and 1mm distance toward direction of crack propagation, and was between 1mm to 3mm distance toward direction of load line.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.46-51
• /
• 2002

Fatigue life estimation by the theoretical stress concentration factors are, in general, considerably different from test results. And in calculating stress concentration factor, it is very difficult to consider actual geometry and material property which are the notch shapes, imperfections or defects of materials such as porosities inclusions and casting defects, etc. Therefore, the paper deals with the experimental method to find out the more exact stress concentration factors by measuring the strain distributions on each specimen by 3D-ESPI(Electronic Speckle Pattern Interferometry) System. Then the fatigue lives are compared between theoretical calculations using stress concentration factors determined by 3D-ESPI system and fatigue test results.

• Transactions of Materials Processing
• /
• v.4 no.3
• /
• pp.245-256
• /
• 1995

SMC(Sheet Molding Compound), a thermoset composite material which consists of unsaturated polyester resin, fiberglass strands, fillers, and various chemical additives for curing agent, has been widely used in fabrication of structural components. The mechanical properties of molded SMS parts are strongly dependent on material flow results during compression molding process, while such flow in molds is affected by material characteristics. For numerical simulation of SMC molding process, estimation of material property of SMC must be accomplished. In this study, flow resistance of SMC was estimated through a simple compression test using a lubricant with grease oil under the constant strain rate condition at various temperatures and the result was compared with other material data available in the literature. The accuracy of the experimentally determined flow resistance was tested by finite element analyses of compression molding of SMC. Simulation results were compared with experimental results under the plane strain condition.

• Geomechanics and Engineering
• /
• v.14 no.4
• /
• pp.315-324
• /
• 2018

With rapid economic growth, numerous deep excavation projects for high-rise buildings and subway transportation networks have been constructed in the past two decades. Deep excavations particularly in thick deposits of soft clay may cause excessive ground movements and thus result in potential damage to adjacent buildings and supporting utilities. Extensive plane strain finite element analyses considering small strain effect have been carried out to examine the wall deflections for excavations in soft clay deposits supported by diaphragm walls and bracings. The excavation geometrical parameters, soil strength and stiffness properties, soil unit weight, the strut stiffness and wall stiffness were varied to study the wall deflection behaviour. Based on these results, a multivariate adaptive regression splines model was developed for estimating the maximum wall deflection. Parametric analyses were also performed to investigate the influence of the various design variables on wall deflections.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.643-650
• /
• 2002

It is necessary, in the light of the importance of long-term slope stability problem, to develop a simple method or tool which can figure out the possible failure zone resulted from weathering effect and other factors. The FBG sensor system is used to estimate the correlations between the temperature and the slope in Yunhwajae, and to find a failure zone in slopes effectively. This research is to seek for the correlation between the soil temperature distribution and the strain distribution in a active zone by analyzing the data from the in-situ measurement so that the possible failure zone should be well defined based on the correlation. The zone of high temperature fluctuation can be regarded as one of the possible sliding zone due to the weathering effect while the constant temperature depth of the ground, if exists, would not be relatively affected by the weathering process.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.704-707
• /
• 2010

구조 건전성 모니터링에 사용되는 기존 센서들의 문제점을 극복하고 높은 분해능과 동특성 모니터링에 대한 이점을 지닌 FBG센서는 구조물 모니터링에 있어 큰 이점을 지니고 있다. FBG 센서는 점 센서라는 한계 때문에 구조물의 전체적인 변형률 및 응력 평가에 어려움이 있을 수 있다. 본 연구에서는 FBG 센서로부터 계측한 변형률 값들로부터 임의의 하중조건에서 철골 보의 변형률 분포를 추정하는 기법을 제시하였다. 임의의 개별 하중조건에 대해 FBG 센서로 계측된 값을 통해 센서의 부착 위치와 최소 필요 개수를 결정하고 변형률 추정식을 유도함으로써 FBG 센서의 계측 기법에 대한 기준을 세웠다. 나아가 임의의 조합 하중이 작용하는 실제의 경우를 고려하여 철골 보의 변형률 분포를 추정하는 보다 일반화된 수학적 모델을 제시하였다. 그리고 예제를 통하여 본 연구에서 제시한 변형률 분포 추정 모델을 검증하였다.