• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.118-121
• /
• 2006

Stick-slip of belt-pulley system produces vibration which results in the noise problem. Experimental study was carried out to investigate the phenomenon of stick-slip with simple v-belt system. The optical displacement sensor detected the vibration caused by the stick-slip of which the frequency was significantly dependant on tension of the belt. The rotation speed of putties also affected the frequency and magnitude of the stick-slip vibration. Existence of misalignment between the driven and drive pulleys made some difference in the stick-slip frequency, but not much. Further study is necessary to identify the generation of noise from the stick-slip vibration.

• 한국음향학회지
• /
• 제43권1호
• /
• pp.49-59
• /
• 2024

최근 환경규제가 강화되고 고유가 문제로 인하여 전기차 시장이 점차 커지고 있으며 또한 내연기관 자동차에서도 엔진의 Noise, Vibration, Harshness(NVH) 관련 소음이 저감되고 외부에서 유입되는 소음의 차폐 기술이 발전됨에 따라 Buzz, Squeak, Rattle(BSR) 이음의 민감도가 증가하는 추세이다. 본 연구에서는 자동차의 Panoramic Curved Display(PCD)에서 발생하는 Stick-slip 이음과 고분자 플라스틱의 표면에너지 및 극성 성분과의 상관관계에 대하여 분석하였다. 극성 고분자 소재인 Acrylonitrile Butadiene Styrene(ABS)와 PolyCarbonate-Acrylonitrile Butadiene Styrene(PC-ABS)를 대상으로 컴파운드 소재를 제작하여 평가하였다. 결과적으로 고분자 플라스틱의 극성성분이 3.86 mN/m 이상일 때 Stick-slip 거동이 발생하였으며, 시간에 따른 마찰 거동에서 absolute transition slope가 증가할수록 Stick-slip의 이음 가능성이 증가하고 마찰계수의 값 차이가 클수록 Stick-slip 이음의 세기가 증가하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.250-251
• /
• 2014

This paper investigates the stick-slip phenomena on spinning shaft. The modeling of the shaft is considered only torsional direction with nonlinear friction. The friction is adopted a negative friction-velocity slope. Based on the model, a nonlinear equation of motion is derived and analyze the stick-slip phenomena. In order to analyze the time dependent response, the nonlinear formulations are numerically solved by nonlinear Newmark method. The numerical results reveal the stick-slip phenomena on the spinning shaft system.

• 한국소음진동공학회논문집
• /
• 제23권9호
• /
• pp.781-788
• /
• 2013

Grunt(stick-slip) noise happens between rear lining and drum on braking condition while vehicle is returning to steady position after nose-dive. The study presents a new testing and analysis methods for improving brake grunt noise on vehicle. Grunt noise is called a kind of stick slip noise with below 1 kHz frequency that is caused by the surfaces alternating between sticking to each other and sliding over each other with a corresponding change in friction force. This noise is typically come from that the static friction coefficient of surfaces is much higher than the kinetic friction coefficient. For the identification of the excitation mechanism and improvement of grunt noise, it is necessary to study variable parameters of rear drum brake systems on vehicle and to implement CAE analysis with stick slip model of drum brake. The aim of this study has been to find solution parameters throughout test result on vehicle and dynamo test. As a result of this study, it is generated from stick slip between rear lining and rear drum and it can be solved to reduce contact angle of lining with asymmetric and is effected not only brake drum strength but also rear brake size and brake factor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.743-749
• /
• 2012

Grunt (Stick-slip) noise happens between rear lining and drum on braking condition while vehicle is returning to steady position after nose-dive. The study presents a new testing and analysis methods for improving brake grunt noise on vehicle. Grunt noise is called a kind of stick slip noise with below 1kHz frequency that is caused by the surfaces alternating between sticking to each other and sliding over each other with a corresponding change in friction force. This noise is typically come from that the static friction coefficient of surfaces is much higher than the kinetic friction coefficient. For the identification of the excitation mechanism and improvement of grunt noise, it is necessary to study variable parameters of rear drum brake systems on vehicle and to implement CAE analysis with stick slip model of drum brake. The aim of this study has been to find solution parameters throughout test result on vehicle and dynamo test. As a result of this study, it is generated from stick slip between rear lining and rear drum and it can be solved to reduce contact angle of lining with asymmetric and is effected not only brake drum strength but also rear brake size and brake factor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.214-215
• /
• 2009

The friction is inevitable and unpredictable phenomena, so most mechanical systems are designed to low friction effect by using bearings and lubricants. However, the slip-stick actuator applies the friction force to its movement. The slip-stick mechanism is applied the piezoelectric actuator to overcome short displacement. Fast response of piezoelectric actuator is also good characteristic for the slip-stick mechanism. However, the piezoelectric actuator with slip-stick mechanism isn't common, because its cost and driving voltage are too high. In this paper, a voice-coil actuator with slip-stick mechanism is introduced. The cost and the driving voltage of a voice-coil actuator are much less than the piezoelectric actuator. And a dynamic vibration amplifier is proposed to adjust the dynamic performance of the actuator. By the results of numerical analysis, the feasibility of a dynamic vibration amplifier is verified.

• 한국소음진동공학회논문집
• /
• 제19권1호
• /
• pp.85-93
• /
• 2009

There are many curves in Seoul subway system. Therefore, the noise from subway system in curved line gives displeasure to passenger. The subway noise in curved line is affected not only by rail condition but also wheel condition and dynamic characteristics. The railway curving noise can be divided into 2 categories. The first is the noise due to stick-slip between wheel tread and rail head, and the second is one by wheel flange contact on rail side. Because of these phenomena - stick-slip and wheel flange contact - wheels are worn seriously. In this study the curving noise was reviewed by using eigen-mode of wheel and waterfall plot which shows noise level in time-frequency domain. And also those were reviewed in viewpoint of stick-slip noise and wheel flange contact noise. Finally, the relationship between curving noise and wheel wear was studied.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.296-303
• /
• 2002

Tribology, in other words, interacting surfaces in relative motion, is essential in life. The relative motion on surfaces may cause some problems with heat, vibration, noise, and so on. Unwanted vibrations by friction, which may arise during the operation of machines, are costly in terms of reduction of performance and service life. All these phenomena inolve stick-slip. The telescopic boom operations involves stick-slip oscillations like slideways. Unwanted stick-slip oscillations on telescopic boom operations cannot achieve smooth sliding and many developers of that machine makes a lot of effort to remove or reduce it. So this paper presents stick-slip oscillation with pressure of the hydraulic cylinder which drives booms, and attempts a theoretical approach for the numerical analysis for its stick-slip condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.690-693
• /
• 2006

As the silence of vehicle is more important, noise reduction of tire is more required. Noise of tire is divided into structure home noise and air borne noise. Tire tread has the property such as Hardness. Pattern Noise is caused by changing of tread hardness. This property has influence on the mechanisms which are Block Impact & Stick-slip sound. In the study, we found that the effect of Hardness is related to more Stick-Slip than Impact.

• 소음진동
• /
• 제10권3호
• /
• pp.451-456
• /
• 2000

In this paper a discrete time model for the identification of nonlinear vibration system with stick-slip friction is proposed. The proposed model can handle the highly nonlinear behavior of the friction such as stick-slip phenomenon and Stribeck effect. The basic idea of the proposed model is as follows : If the nonlinearity of the system can be predicted as a simple function then this nonlinear function term cab be directly used in the discrete time model. By doing this the number of nonlinear terms in the model can be much less than those of NARMAX model which is widely used nonlinear discrete model. The simulation result shows that the proposed model can estimate the response of the nonlinear vibration system with stick-slip friction very well with less computational effort.