• 전력전자학회논문지
• /
• 제7권5호
• /
• pp.419-426
• /
• 2002

전류원 하프브릿지 듀얼 컨버터(이하 '듀얼 컨버터')를 위한 새로운 능동형 무손실 스너버가 제안된다. 제안된 능동형 무손실 스너버는 주 스위치의 턴 오프 시 변압기 누설 인덕터로 인해 발생되는 스위치 양단 전압 서지를 흡수해줄 뿐만 아니라 주 스위치 및 부가된 보조스위치의 턴 온 시 영전압 스위칭까지 보장해 주기 때문에 스위칭손실을 거의 무시할 수 있으며, 고 효율 및 고속 스위칭에 매우 유리한 장점을 가져 높은 전력밀도를 가진 고성능승압형 컨버터의 구현을 가능하게 한다. 또한 영전압 스위칭을 위해 별도의 인덕터 없이 변압기의 누설 인덕터만으로 그 구현이 가능하며 보조 스위치의 구동신호가 주 스위치와 교대로(complementary) 온 오프 되므로 별도의 PWM IC가 필요 없는 간단한 구조를 가지며, 제작 시 단가 절감 효과를 얻을 수 있다. 본 논문에서는 기존에 제안된 바 있는 듀얼 컨버터에 제안된 능동형 무손실 스너버를 적용하여 그 동작 원리, 영전압스위칭 조건, 그리고 설계방법 등에 대해 살펴보고 최종적으로 제시된 이론적인 분석결과 및 동작의 유효성 검증을 위해 24V/DC 입력에 200V/DC 출력을 갖는 200W급 축소모델을 제작하여 100kHz로 구동한 실험 결과를 제시한다.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.133-144
• /
• 1999

To fine seam annealer capacity of through thickness seam annealing in terms of through thickness microstructure change with increased toughness and elongation leaving heat trace on it, high strength steel pipes of ERW with different thickness were tested in different seam annealing temperature measured on the outer surface of pipes. Annealing temperature and microstructure of the weld seam were changed through applied seam annealing condition. Toughness and tensile test with hardness and microstructure analysis were done on the annealed weld seam to fine its characteristics as a primary step and annealing characteristics according to different seam annealing condition. Through a study of annealed ERW weld seam characteristics and seam annealing technology, amount of electric power should apply in decreased manner to arranged inductors of annealer in the order of 1st, 2nd, 3rd, so on for proper seam annealing. For example of 15.4mm thick and 610mm outside diameter pipe, applied power for proper seam annealing is 600 -650kw at 1st inductor, 450 - 500kw at 2nd inductor, 200-250 kw at 3rd inductor of annealer during 10 - 12M/minute moving speed of pipe. Also, the penetration depth of heat trace along the thickness direction of weld during seam annealing can be estimated through the equation 17mm/kv$\times$voltage(kv) with the microstructure and hardness analysis of thick weld seam as well as study of seam annealing and comparison of cooling condition to CCT diagram of low carbon high strength steel. From this result, the difference between the technological applicability of full annealing condition based on phase diagram and full penetration of heat trace based on CCT diagram along the thickness of weld seam is discussed.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권1호
• /
• pp.10-13
• /
• 2015

High-temperature superconducting coated conductors (HTS-CCs) are good candidates for resistive superconducting fault current limiter (RSFCL) applications. However, the high current density they can carry and their low thermal diffusivity expose them to the risk of thermal instability. In order to find the best compromise between stability and cost, it is important to study the heat transfer between HTS-CCs and the liquid nitrogen ($LN_2$) bath. This paper presents an experimental method to monitor in real-time the temperature of a quenched HTS-CC during a current pulse. The current and the associated voltage are measured, giving a precise knowledge of the amount of energy dissipated in the tape. These values are compared with an adiabatic numerical thermal model which takes into account heat capacity temperature dependence of the stabilizer and substrate. The result is a precise estimation of the heat transfer to the liquid nitrogen bath at each time step. Measurements were taken on a bare tape and have been repeated using increasing $Kapton^{(R)}$ insulation layers. The different heat exchange regimes can be clearly identified. This experimental method enables us to characterize the recooling process after a quench. Finally, suggestions are done to reduce the temperature increase of the tape, at a rated current and given limitation time, using different thermal insulation thicknesses.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권10호
• /
• pp.438-442
• /
• 2005

Si nanocrystal (Si NC) memory device has several advantages such as better retention, lower operating voltage, reduced punch-through and consequently a smaller cell area, suppressed leakage current. However, the physical and electrical reasons for this behavior are not completely understood but could be related to interface states of Si NCs. In order to find out this effect, we characterized electrical properties of Si NCs embedded in a SiO$_{2}$ layer by scanning probe microscopy (SPM). The Si NCs were generated by the laser ablation method with compressed Si powder and followed by a sharpening oxidation. In this step Si NCs are capped with a thin oxide layer with the thickness of 1$\~$2 nm for isolation and the size control. The size of 51 NCs is in the range of 10$\~$50 m and the density around 10$^{11}$/cm$^{2}$ It also affects the interface states of Si NCs, resulting in the change of electrical properties. Using a conducting tip, the charge was injected directly into each Si NC, and the image contrast change and dC/dV curve shift due to the trapped charges were monitored. The results were compared with C-V characteristics of the conventional MOS capacitor structure.

• 한국표면공학회지
• /
• 제46권1호
• /
• pp.29-35
• /
• 2013

The effect of DC bias on the growth of nanocrystalline diamond films on silicon substrate by microwave plasma chemical vapor deposition has been studied varying the substrate temperature (400, 500, 600, and $700^{\circ}C$), deposition time (0.5, 1, and 2h), and bias voltage (-50, -100, -150, and -200 V) at the microwave power of 1.2 kW, working pressure of 110 torr, and gas ratio of Ar/1%$CH_4$. In the case of low negative bias voltages (-50 and -100 V), the diamond particles were observed to grow to thin film slower than the case without bias. Applying the moderate DC bias is believed to induce the bombardment of energetic carbon and argon ions on the substrate to result in etching the surfaces of growing diamond particles or film. In the case of higher negative voltages (-150 and -200 V), the growth rate of diamond film increased with the increasing DC bias. Applying the higher DC bias increased the number of nucleation sites, and, subsequently, enhanced the film growth rate. Under the -150 V bias, the height (h) of diamond films exhibited an $h=k{\sqrt{t}}$ relationship with deposition time (t), where the growth rate constant (k) showed an Arrhenius relationship with the activation energy of 7.19 kcal/mol. The rate determining step is believed to be the surface diffusion of activated carbon species, but the more subtle theoretical treatment is required for the more precise interpretation.

• 한국동물위생학회지
• /
• 제25권1호
• /
• pp.23-29
• /
• 2002

A method was developed to separate, detect and qualify aldicarb, bendiocarb, carbaryl, carbofuran, ethiofencarb, methomyl, methiocarb, propoxur in meats and fruits. Experimental beef and fork samples were fortified with 0.05mg/kg of carbamate pesticides for analysis. Carbamate-detected pear by HPLC fluorescence detector(HPLC/FLS) are extracted with acetonitril and refined by solid phase extraction(SPE) filled with aminopropyl-bonded silca, In the following step, the injected materials into LC/MS are analyzed to result in the fact that bendiocarb, carbaryl, carbofuran, ethiofencarb, methomyl, methiocarb, propoxur presents several sorts of fraction ions following with; [M+H]$^{+}$, [M+Na]$^{+}$,［M-CONH$CH_3$]$^{+}$, [M-OCONH$CH_3$]$^{+}$. In addition, ethiofencarb presents [M-SCH$_2$$CH_3$]$^{+}$ ion distinctive and aldicarb presents [M+Na]$^{+}$ and [M-OCONH$CH_3$]$^{+}$ ion which is the most decisive fraction ion for pesticides such as bendiocarb, carbaryl, carbofuran, ethiofencarb, methiocarb, methomyl, propoxur excluding [M+H]$^{+}$ ion. However, [M-OCONH$CH_3$]$^{+}$ and [M-OCONH$CH_3$]$^{+}$ fraction ion charactering carbamate pesticides are detected most efficiently with fragment voltage 50ev. As a result, for rluantitative analysis, [M+Na]$^{+}$ ion is the most decisive ion for detection of aldicarb and [M+H]$^{+}$ ion is the most decisive fraction ion for Pesticides such as bendiocarb, carbaryl, carbofuran, ethiofencarb, methiocarb, methomyl, propoxur. Carbaryl-detected pear by HPLC/FLS are analyzed by L/MS and the result shows that [M+H]$^{+}$ and [M-CONH$CH_3$]$^{+}$ ions charactering carbaryl are detected.ering carbaryl are detected.

• 한국수소및신에너지학회논문집
• /
• 제23권4호
• /
• pp.373-381
• /
• 2012

To determine the performance characteristics of motorcycle engine using biogas for practical use, the intake system of a 110 cc motorcycle engine is properly modified to operate with biogas as a fuel. Biogas is a potentially renewable fuel for replacing gasoline in future, but it has high percentage of $CO_2$ that could lead to slow the burning rate of biogas-air mixture and cause instability in combustion. Thus, the performance characteristics of biogas-fueled motorcycle engines could be different from those of gasoline motorcycle engines. In this paper, the important parameters of performance characteristics (such as: power output, thermal efficiency, fuel consumption, exhaust emission,${\cdots}$) of biogas-fueled motorcycle engine are studied and estimated with change of engine speed and load. The obtained results when operating with biogas are used to compare with that of gasoline fuel under the same operating conditions. Engine speed in the experimental is changed from 1500 rpm (idle-mode) up to 3500 rpm by a step of 500 rpm. Engine load is changed from zero to maximum load with the help of an exciting voltage device from generator-type dynamometer. The experimental results show that the tested engine operated with richer biogas-air mixture than that of gasoline-air mixture under the same test conditions. Biogas-fueled engine gives a higher fuel consumption and lower thermal efficiency under the same power output. Brake thermal efficiency of biogas engine is found to be about 3% lower than gasoline-fueled motorcycle engine for whole range of speed. Exhaust emission of biogas-fueled motorcycle engine (such as: CO, HC) is found to be lower than the limitation level of the emission standards of Vietnam for motorcycle engines (CO <4.5% HC <1200 ppm).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 C
• /
• pp.918-922
• /
• 1998

With the development of industry, the qualitical advancement of power is needed. Since it is placed in the end step of power system, the fault at the distribution system causes some users blackout directly. So if the fault occurs, quick restoration is very important subject and, for the reason, induction of the distribution automation system is now being progressed briskly. For the quick restoration of the faulted distribution system, the load shedding of the blackout-area must be followed, and the other problems like the shedded load, faulted voltage and the rest may cause other accident. Accordingly load shedding must be based on the precise calculation technique during the distribution system load flow(dist flow) calculation. In these days because of its superior convergence characteristic the Newton-Raphson method is most widely used. The number of buses in the distribution system amounts to thousands, and if the fault occurs at the distribution system, the speed for the dist flow calculation is to be improved to apply to the On-Line system. However, Newton-Raphson method takes much time relatively because it must calculate the Jacobian matrix and inverse matrix at every iteration, and in the case of huge load, the equation is hard to converge. In this thesis. matrix equation is used to make algebraical expression and then to solve load flow equation and to modify above defects. Then the complex matrix is divided into real part and imaginary part to keep sparcity. As a result time needed for calculation diminished. Application of mentioned algorithm to 302 bus, 700 bus, 1004 bus system led to almost identical result got by Newton-Raphson method and showed constant convergence characteristic. The effect of time reduction showed 88.2%, 86.4%, 85.1% at each case of 302 bus, 700 bus system 86.4%, and 1004 bus system.

• 전자공학회논문지C
• /
• 제35C권10호
• /
• pp.22-29
• /
• 1998

본 논문에서는 휴대용 영상신호처리 시스템에 집적화할 수 있는 전류예측기와 모듈형 기준전류원을 이용한 10비트 저전력 전류구동 CMOS A/D 변환기를 설계하였다. 전류예측기와 모듈형 기준 전류원을 사용함으로써 2단 플래시구조를 갖는 A/D 변환기에 비해 비교기와 기준전류원의 개수를 줄일 수 있게 되었고, 따라서 설계된 A/D변환기의 저전력 동작이 가능하였다. 설계된 10비트 저전력 전류구동 CMOS A/D 변환기는 0.6㎛ n-well single-poly triple metal CMOS 공정을 사용하여 제작되었다. +5V 단일 공급전압하에서 동작할 때 측정된 전력소모는 94.4mW이며, 아날로그 입력 전류범위는 16㎂에서 528㎂로 측정되었으며, INL과 DNL은 각각 ±1LSB, ±0.5LSB이하로 나타났다. 또한 10MSamples/s의 변환속도를 나타내었고, 제작된 10비트 전류구동 CMOS 4/D 변환기의 유효 칩면적은 1.8㎜ x 2.4㎜이다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권1호
• /
• pp.83-91
• /
• 2014

This paper presents a capacitive readout circuit for tri-axes microaccelerometer with sub-fF offset calibration capability. A charge sensitive amplifier (CSA) with correlated double sampling (CDS) and digital to equivalent capacitance converter (DECC) is proposed. The DECC is implemented using 10-bit DAC, charge transfer switches, and a charge-storing capacitor. The DECC circuit can realize the equivalent capacitance of sub-fF range with a smaller area and higher accuracy than previous offset cancelling circuit using series-connected capacitor arrays. The readout circuit and MEMS sensing element are integrated in a single package. The supply voltage and the current consumption of analog blocks are 3.3 V and $230{\mu}A$, respectively. The sensitivities of tri-axes are measured to be 3.87 mg/LSB, 3.87 mg/LSB and 3.90 mg/LSB, respectively. The offset calibration which is controlled by 10-bit DECC has a resolution of 12.4 LSB per step with high linearity. The noise levels of tri-axes are $349{\mu}g$/${\sqrt}$Hz, $341{\mu}g$/${\sqrt}$Hz and $411{\mu}g$/${\sqrt}$Hz, respectively.