• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1460-1462
• /
• 1994

BiCMOS is the newly developed technology that integrates both CMOS and bipolar structures on the same integrated circuit. Improved performance can be obtained from combining the advantages of high density and low power in CMOS with the speed and current capibility advantages by bipolar. However, the major drawbacks to BiCMOS are high cost, long fabrication time and difficulty of merging CMOS with bipolar without degrading of device Performance because CMOS and bipolar share same process step. In this paper, N-Well CMOS oriented BiCMOS process and optimization of device performance are studied when N-Well links CMOS with bipolar process step by 2D process and 3D Device simulation. From the simulation, Constriction of linking process step has been understood and provided to give the method of choosing BiCMOS for various analog design request.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.81-88
• /
• 1999

This paper was carried out to know the influence of advanced austempered ductile cast iron (ADI) on the tool life and mechanical properties of drilling machinability. For manufactured method of ADI, the spheroidal graphite cast iron were austenized at 90$0^{\circ}C$ for 1 hour and then austempered for 2 hour at 37$0^{\circ}C$ in the salt bath. And interrelationship has been investigated between tool life and mechanical characteristics of specimen material on drilling condition when the ordinary and step-feed drilling are carried out to drill holes of specimens. Tensile strength and hardness of ADI decrease and elongation of ADI increases with the increase austempered temperature. It is known that about 2 times of tool life in the case of step-feed decreases compared with ordinary feed due to the high hardness of ADI and hardness ascribed to the fact that retained austenite became to martensite state due to cutting heat in drilling. Under the constant feed rate 0.1mm/rev relation between hardness and length of end tip after drilling can be formularized to Hv=$788.46L^{-0.096}$ for the cutting speed 6.1m/min.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.598-603
• /
• 2007

The active control technique mostly uses the Least-Mean-Square (LMS) algorithm, because the LMS algorithm can easily obtain the complex transfer function in real-time, particularly when the Filtered-X LMS (FXLMS) algorithm is applied to an active noise control (ANC) system. However, FXLMS algorithm has the demerit that stability of the control is decreased when the step size become larger but the convergence speed is faster because the step size of FXLMS algorithm is fixed. As a result, the system has higher probability which the divergence occurs. Thus the Co-FXLMS algorithm was developed to solve this problem. The Co-FXLMS algorithm is realized by using an estimate of the cross correlation between the adaptation error and the filtered input signal to control the step size. In this paper, the performance of the Co-FXLMS algorithm is presented in comparison with the FXLMS algorithm. Simulation results show that active noise control using Co-FXLMS is effective in reducing the noise in duct system.

• Journal of Korean Society of Transportation
• /
• v.26 no.2
• /
• pp.101-107
• /
• 2008

Traffic speed data may be missed due to detector malfunction or network problems. In this paper we have proposed effective methods to estimate the data which could not be collected through loop detectors. Our proposed algorithm has three steps. First step is to find the most similar neighbor data record by coefficient of correlation. Second step is to make some data records which is calculated by the 5 kinds of estimation methods. Third step is to compare the data records with history data record of observation link and thus the best method is selected. The proposed method is useful for estimating travel time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.759-764
• /
• 2009

In this paper designed One-Step mobile shopping system using Multipurpose Visual Language System(MVLS). MVLS is based on braille system, and list this to a square color box. This is can accomplish convenience of use and encipherment of fundamental personal information. Also, this system has advantage to fast communication speed because that has little size packets. Planed system does and fit this in shopping to graft together mobile-phone that the such MVLS and most of internal adult are possessing. User can more fast finish shopping just photographing and press the button that show on TV or PC monitor and printed materials etc. by camera of mobile phone.

• East Asian mathematical journal
• /
• v.22 no.2
• /
• pp.249-257
• /
• 2006

Let n be a 2-step nilpotent Lie algebra which has an inner product <,> and has an orthogonal decomposition $n=\delta{\oplus}\varsigma$ for its center $\delta$ and the orthogonal complement $\varsigma\;of\;\delta$. Then Each element Z of $\delta$ defines a skew symmetric linear map $J_Z:\varsigma{\rightarrow}\varsigma$ given by $=$ for all $X,\;Y{\in}\varsigma$. Let $\gamma$ be a unit speed geodesic in a 2-step nilpotent Lie group H(2, 1) with its Lie algebra n(2, 1) and let its initial velocity ${\gamma}$(0) be given by ${\gamma}(0)=Z_0+X_0{\in}\delta{\oplus}\varsigma=n(2,\;1)$ with its center component $Z_0$ nonzero. Then we showed that $\gamma(0)$ is conjugate to $\gamma(\frac{2n{\pi}}{\theta})$, where n is a nonzero intger and $-{\theta}^2$ is a nonzero eigenvalue of $J^2_{Z_0}$, along $\gamma$ if and only if either $X_0$ is an eigenvector of $J^2_{Z_0}$ or $adX_0:\varsigma{\rightarrow}\delta$ is not surjective.

• Physical Therapy Korea
• /
• v.10 no.4
• /
• pp.77-83
• /
• 2003

본 연구는 발가락 벌림 보조기(toe spreader)가 긴장성 발가락 굽힘 반사(Tonic Toe Flexion Reflex: TTFR)가 있는 양하지 뇌성마비 아동의 보행에 미치는 영향을 알아보고자 하였다. 12명의 TTFR이 있는 양하지 뇌성마비 아동을 대상으로 같은 날에 맨발과 발가락 벌림 보조기를 착용한 상태에서 보행분석을 실시하였다. 시간 거리 보행변수로 활보장(step length), 보장(step length), 보폭(step width), 발가락 외전각도(toe out angle), 활보시간(stride), 입각기(stance phase), 유각기(swing phase), 분속수(cadence), 보행속도(speed)를 측정하였다. 발가락 벌림 보조기 착용 시 시간 거리 보행변수는 통계적으로는 유의한 차이가 없었다(p>.05). 양하지 뇌성마비 아동에서 TTFR을 억제하기 위한 발가락 벌림 보조기의 즉시적인 효과는 유의하지 않다고 볼 수 있으며, 추후연구로 장기간 일상생활에서의 지속적인 착용을 통한 연구가 필요하다고 본다.

• International Journal of CAD/CAM
• /
• v.3 no.1_2
• /
• pp.51-60
• /
• 2003

The growth of the World Wide Web and the advances in high-speed network access have greatly changed existing CAD/CAE environment. The WWW has enabled us to share various distributed product data and to collaborate in the design process. An international standard for the product model data, STEP, and a standard for the distributed object technology, CORBA, are very important technological components for the interoperability in the advanced design and manufacturing environment. These two technologies provide background for the sharing of product data and the integration of applications on the network. This paper describes a distributed CAD/CAE environment that is integrated on the network by CORBA and product model data standard STEP. Several prototype application modules were implemented to verify the proposed concept and the test result is discussed. Finite element analysis server are further distributed into several frontal servers for the implementation of distributed parallel solution of finite element system equations. Distributed computation of analysis server is also implemented by using CORBA for the generalization of the proposed method.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.51-53
• /
• 2006

This paper proposes a portable ECG monitoring system, which integrates uptodate PDA and RF communication technology. The aim of the study is to acquire the subject's biomedical signal without any constraint. It has two types of transmission mode, which are total signal transmission mode and HR(heart rate)/SC(step count) transmission mode. In audition, wireless communication technology uses Zigbee Wireless PAN and can work in low-power mode, which is one of the advantages of ZiBbee communication technology. The developed system is composed of a transmitter and a receiver. The transmitter has three-axial acceleration sensor. ECG amplifier and Zigbee communication controller. In total signal transmission mode, it can send data 50 packets per second whose transmission speed corresponds to 300 ECG samples and 60 acceleration samples. In HR/SG transmission mode, it can calculate heart rate from EEG data with 216 samples per second and step count from acceleration data and send a packet every cardiac cycle. The receiver forwards the received data to PDA, where the data can be stored and displayed. Therefore, the developed device enables to continuous monitoring for Activities of Daily Living(ADL). Also, this method will reduce medical costs in the aged society.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.464-469
• /
• 1999

Recently, the need for designing multi-stage gear drive has been increased as the hear drives are used more in the applications with high-speed and small volume. The design of multi-stage gear drives includes not only dimensional design but also configuration design of various machine elements. Until now, however, the researches on the design of gear drives are mainly focused on the single-stage gear drives and the design practices for multi-stage gear drives, especially in configuration design activity, mainly depend on the experiences and 'sense' of the designer by trial and error. We propose a design algorithm to automate the dimension design and the configuration design of multi-stage gear drives. The design process consists of four steps. The number of stage should be determined in the first step. In second step, the gear ratios of each reduction stage are determined using random search, and the ratios are basic input for the dimension design of gears, which is performed by the exhaustive search in third step. The designs of gears are guaranteed by the pitting resistance and bending strength rating practices by AGMA rating formulas. In configuration design, the positions of gears are determined to minimize the volume of gearbox using simulated annealing algorithm. The effectiveness of the algorithm is assured by the design example of a 4-stage gear drive.