• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.83-89
• /
• 2013

An adaptive blind equalization is a technique using to minimize the Inter-symbol Interference occurred on a communication channel in the transmission of the high speed digital data. In this paper, we propose a blind equalization more improving performance of the conventional MSAGF-MMA adaptive blind equalization algorithm by applying a multiple step size. This algorithm apply a LMS algorithm with a several step size according to each region divided by absolute values of decision-directed error to MSAGF-MMA. By computer simulation, it is confirmed that the proposed algorithm has a performance highly enhanced in terms of a convergence speed, a residual ISI and a residual error and an ensemble averaged MSE in a steady status compared with MMA and MSAGF-MMA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.4C
• /
• pp.305-311
• /
• 2008

In this paper, we proposed an algorithm for adaptive noise cancellation (ANC) using the variable step size normalized least mean square (VSSNLMS) in real-time automobile environment. As a basic algorithm for ANC, the LMS algorithm has been used for its simplicity. However, the LMS algorithm has problems of both convergence speed and estimation accuracy in real-time environment. In order to solve these problems, the VSSLMS algorithm for ANC is considered in nonstationary environment. By computer simulation using real-time data acquisition system(USB 6009), VSSNLMS algorithm turns out to be more effective than the LMS algorithm in both convergence speed and estimation accuracy.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.4
• /
• pp.497-504
• /
• 2017

This paper proposes a method to measure the airburst height by utilizing a high speed camera. This method might be applied to the test of which flight target is alive after the burst. The proposed method consists of four main steps. The first step is to compute the impact point using the sea surface height. The second step is to compute the height of burst (HOB) by using the distance from the camera to the impact point. This could be different from the real explosion height. That is because the distance from the camera to the burst point is not the same as it from the camera to the impact point. Therefore, the third step is to calculate the approach angle of the flight target with respect to the installed camera. Then, the last step is to compensate the computed height by using the approach angle. The result of the proposed method is compared with it from the triangulation. In this paper, the HOB error is also analyzed regarding the approach angle difference. Based on this analysis, the camera position might be suggested for error reduction.

• Journal of Information Processing Systems
• /
• v.16 no.4
• /
• pp.832-844
• /
• 2020

The degree of dispersion of a random variable can be described by the variance, which reflects the distance of the random variable from its mean. However, the time complexity of the traditional variance calculation algorithm is O(n), which results from full calculation of all samples. When the number of samples increases or on the occasion of high speed signal processing, algorithms with O(n) time complexity will cost huge amount of time and that may results in performance degradation of the whole system. A novel multi-step recursive algorithm for variance calculation of the time-varying data series with O(1) time complexity (constant time) is proposed in this paper. Numerical simulation and experiments of the algorithm is presented and the results demonstrate that the proposed multi-step recursive algorithm can effectively decrease computing time and hence significantly improve the variance calculation efficiency for time-varying data, which demonstrates the potential value for time-consumption data analysis or high speed signal processing.

• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.9-16
• /
• 2011

To develop a 6061 aluminum alloy with low residual stress and high tensile strength, a cryogenic treatment process was investigated. Compared to the conventional heat treatment process for precipitation hardening with artificial aging, the cryogenic treatment process has two additional steps. The first step is cryogenic quenching of the sample into liquid nitrogen, the second step is up-hill quenching of the sample into boiling water. The residual stress for the sample was measured by the $sin^2{\psi}$ method with X-ray diffraction. The 6061 aluminum alloy sample showed 67% relief in stress at the cryogenic treatment process with artificial aging at $175^{\circ}C$. From this study, it was found that the optimum cryogenic treatment process for a sample with low residual stress and high tensile strength is relatively low cooling speed in the cryogenic quenching step and a very high heating speed in the up-hill quenching step.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.224-227
• /
• 1993

In this paper, a new LMS algorithm with a variable step size (VVS LMS) is presented. The change of step size .mu. at each iteration, which increases or decreases according to the misadaptation degree, is computed by a proportional fuzzy logic controller. As a result the algorithm has very good convergence speed and low steady-state misadjustment. The norm of the cross correlation between the estimation error and input signal is used. As a measure of the misadaptation degree. Simulation results are presented to compare the performance of the VSS LMS algorithm with the normalized LMS algorithm.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.203-206
• /
• 1998

This paper describes the procedure of getting information about auto-tuning of PID regulator by the injection of high step input, called limited input, during a transient time of control. The key point is that system identification and control could be continuously executed. This means that the system information obtained by limited input despite of system uncertainty can be continuously applied to the PI regulator. Simulation and experiment result of brushless DC motor system having monotone increasing step response demonstrate the usefulness of proposed auto-tuning algorithm.

• Journal of Industrial Technology
• /
• v.13
• /
• pp.33-41
• /
• 1993

In this paper, a new LMS algorithm with a fuzzy variable step size (FVS LMS) is presented. The change of step size ${\mu}$, at each iteration which is increases or decreases according to the misadaptation degree, is computed by a proportional fuzzy logic controller. As a result the algorithm has very good convergence speed and low steady-state misadjustment. As a measure of the misadaptation degree, the norm of the cross correlation between the estimation error and input signal is used. Simulation results are presented to compare the performance of the FVSS LMS algorithm with the normalized LMS algorithm.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.4
• /
• pp.235-240
• /
• 2024

We designed this study because it is necessary to take health care from middle age for to healthy old age. The purpose of this study was to confirm the effect of middle-aged women on the walking mechanism by applying an exercise program that can achieve the maximum effect through simple exercise regardless of time and place. A total of 20 subjects were selected from middle-aged women aged 45 years or older, with 10 calf-enhancing exercise groups and 10 control groups. As a result of comparing before and after exercise in the calf-enhancing exercise group, the step length left and right, and double support, step time, and speed were improved. As a result of comparing the walking mechanisms of the calf-enhancing exercise group and the non-exercise group after exercise, the step length left and right, and step time left and right were improved. The positive effect of the walking mechanism was shown through the calf-enhancing exercise regardless of time and place. In particular, it is judged that the stride was widened, resulting in an increase in the speed of walking due to the strength of the lower extremities and the shortening of the one-foot support section, resulting in meaningful results. In future studies, it is considered desirable to present measurement data for each life cycle by evaluating all ages, such as adolescents and the elderly, and to provide it as basic data for causing social problems due to lack of normal exercise.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.672-675
• /
• 1997

This paper proposes a structure of the control system for the step & scan exposure tool. The step & scan exposure tool is used for the manufacturing process of the semiconductor DRAM memory of giga bit. The control system employs the VME bus instead of the conventional ISA bus so that all control signals and data can be managed separately by the 4 VME-PCs for fast and fault-free flow of signals for multi-tasking. A high speed I/O card is equipped for the real-time monitoring and control of the sub module equipment. Then all the subsystems are integrated and aligned for the operation of the step & scan exposure tool with the VME bus and, I/O card.